check that out guys .. hope you like it ... if so give us an like and share ... stay tuned for our next Project.. how to install an elektric-junkys LED Strip IR TOUCH SENSOR ... enjoy...
Unfortunately this video only shows one difference between the two chips. Another significant difference is the 2812b runs at a 400 hz refresh rate while the 2813 runs at 2000 hz.
Thank you for posting this video. I do have a question at Min. 1:40 you only cut one lead (right one) on the WS2813 and you cut both leads on the WS2812B at Min. 2:00. Why did you not cut both lead on the WS2813 ?... Cutting both leads on both tapes be a more accurate???
hi we have different Chipsets also Newest Addressable LED Strip with Highest Refresh Rates. Get in Touch we are Located in Shenzhen China elektric-junkys.com
You can easily cut out the dead LED and solder the two half's together. Yes, buying the more expensive WS2813 is less of a hassle but just having a dead LED would drive me crazy!
hi, that is right .. if you build a Flexible Screen like we do over and over again is pretty annoying as if you roll the screen you can imagine what happens with the cheapest aliexpress WS2812b .. as cheaper the LED Light Strips you can imagine the Quality Level dump .. less Layer of copper on pcb, less solder, less time in the oven and so on ...check out our website for more infos
hi, actually pretty often if you not care it well .. step on it overbend it or mistakenly break it, based on the quality and layer of pcb the LED´s may break even when you roll it ...
i use ws 2812b a lot for room decor. Luckily, i have never encountered dead leds. But a common problem is the driver/controller, not the strip. many different drivers i used use to go crazy after sometimes
Hi, can you tell me how to do it, if i want for the ws2813, to be turned on anytime on red? Or yellow? If i connect a power source of 12v, from the car, i need a controler to lock the led strip on red or yellow? Thank you
I am installing RBGW on my boat. Underneath the rub rail. I want a nice contoller that has music sync and or like DMX sync type contoller. Via remote or and Iphone. Lights I want is the waterproof IP65. What strip and what controller do you rccomend?
thank´s for comment Each RGB LED draws approximately 50 mA when it is set to full brightness and powered at 5 V. This means that for every 30 LEDs you turn on, your LED strip could be drawing as much as 1.5 A.
4:58 for that tiny bit of info... is a waste of video time slot. Perhaps more information using texts aince you've already using them in the video anyway...
check that out guys .. hope you like it ... if so give us an like and share ... stay tuned for our next Project.. how to install an elektric-junkys LED Strip IR TOUCH SENSOR ... enjoy...
Unfortunately this video only shows one difference between the two chips. Another significant difference is the 2812b runs at a 400 hz refresh rate while the 2813 runs at 2000 hz.
thank´s for comment visit our website elektric-junkys.com
Thank you for posting this video. I do have a question at Min. 1:40 you only cut one lead (right one) on the WS2813 and you cut both leads on the WS2812B at Min. 2:00. Why did you not cut both lead on the WS2813 ?... Cutting both leads on both tapes be a more accurate???
hi thanks for comment .. that was just an example to explain how the strips react if 1 LED is dead !
Cutting one makes the LED just as non-functional as cutting both.
WS2813 --- 5V with powerbank?
yes exactly please stay tuned we are coming up with a 5V Powerbank Project soon, thank´s for comment Friend !
Very helpful demo. Thanks
Thanks for comment mate !
What led controller are you using?
hi, WS2813 controller check our website for more infos elektric-junkys.com
I got 20m of 5050 are they still compatible?
How is refresh rate. Which is faster to animate on?
hi we have different Chipsets also Newest Addressable LED Strip with Highest Refresh Rates. Get in Touch we are Located in Shenzhen China elektric-junkys.com
Do all WS2813 has 4 end connectors?
hi, depends on the Voltage.. please check it on our website elektric-junkys.com you will find more infos
@@ejunky66
Seen it. So WS2813 has a 5v option. Interesting. How is the heat on it? Does it run hotter than WS2812b?
You can easily cut out the dead LED and solder the two half's together. Yes, buying the more expensive WS2813 is less of a hassle but just having a dead LED would drive me crazy!
hi, that is right .. if you build a Flexible Screen like we do over and over again is pretty annoying as if you roll the screen you can imagine what happens with the cheapest aliexpress WS2812b .. as cheaper the LED Light Strips you can imagine the Quality Level dump .. less Layer of copper on pcb, less solder, less time in the oven and so on ...check out our website for more infos
What model is the universal controller?
Contact us elektric-junkys.com we are manufacturing Controllers and Striplights Shipping World Wide with DHL Express
How often did a ws2812b LED die on you?
hi, actually pretty often if you not care it well .. step on it overbend it or mistakenly break it, based on the quality and layer of pcb the LED´s may break even when you roll it ...
i use ws 2812b a lot for room decor. Luckily, i have never encountered dead leds. But a common problem is the driver/controller, not the strip. many different drivers i used use to go crazy after sometimes
I can't find these seperate I need 8 but they need to be further apart, is this possible ?
hi, simply get the KIT from us .. we help you to find the Best Solution for you ! thanks for comment
Is this similar to the old dream color 133 pattern lights I have with the big tan control box? If so, will the tan control box work these strips?
no not going to work .. special controllers are necc. you can find on elektric-junkys.com
I cannot find that universal controller 4:03 on your website. Help?
hi, checkout the controller section on our website .. we will update it soon ..
Do you sell the bottom strip of that assembly line? I have lots of 2812b strips and this would allow me to use them all up in a set up like this?
hi .. sure .. send us an email elektric-junkys.com
What controller you use?
elektric-junkys controller, can be found on our website
@@ejunky66 what model was used in this video?
Can I control WS2812 over DMX directly from Artnet using Data + output?
hi, yes should be possible .. send us an email for more infos elektric-junkys.com
What controllers are available now for ws2813? Need to play video on ws2813 display.
hi we have a bunch of controllers on our website .. check it out www.elektric-junkys.com/index.php?route=product/category&path=60_70
Nice, significant improvement. What’s the difference in price?
hi, about 3$ Meter thanks for comment !
Nice one,greeting from indonesia
thank´s mate greeting back from China !
Hi, can you tell me how to do it, if i want for the ws2813, to be turned on anytime on red? Or yellow? If i connect a power source of 12v, from the car, i need a controler to lock the led strip on red or yellow? Thank you
Hi Mate sure .. send us an email we will guide you on how to use our Material ...
ejunky66 Hi mate, can you leave your e-mail please? I have some questions for you for my tail lights project. Thank you
t300k and ws2812b sreen diy 'can?
sure can just send us an email .. check out our new Video th-cam.com/video/IgSmokI1yy0/w-d-xo.html
Can you tell me, please if exist somewhere addressable LED chain, similar to WS2823B, but white and not RGB?.
hi, we assemble all existing Flex pcb´s just send us an email and we will quote you quickly .. cheers elektric-junkys.com
Where on your site is info about the flex screen system?
hi .. check it out ... www.elektric-junkys.com/index.php?route=product/product&product_id=57
Very great, nice Greetings from germany
thanks mate ;) greetz to you too
awsome explaination,i can understand the difference clearly.thank you so much for this video.thumbs up ejunky66,very simple and to the point setup.
Thanks very much mister Swan please get in touch with us .. maybe we can start a Project togheter elektric-junkys.com contact us
I am installing RBGW on my boat. Underneath the rub rail. I want a nice contoller that has music sync and or like DMX sync type contoller. Via remote or and Iphone. Lights I want is the waterproof IP65. What strip and what controller do you rccomend?
hi jeff thanks for comment .. please send us an email for clear out your project elektric-junkys.com see ya ...
mate send us an email not add your email address here :) ... ... use contact form on our website
I did that,
that´s great
How much voltage does it need in power supply?
hi Happy New Year .. we have 5V/12V/24V Light Sources .. check it out elektric-junkys.com
So ws2812b is still same like ws2811? I want buy addressable led with 12v power
yes thats the same not to advice .. send us an email for an KIT Price
@@ejunky66 btw can i get 12v with 4pin? I see there only have 3pin right now..
can you tell us than which is better 1-6803 or 2-WS2813 ?
hi, just send us an email we will guide you on your Project .. we are Manufacturer in Shenzhen China !
Wa2812b ripper kese kare please videos banado na bhai
Thank you so much for comment my friend shot us an email for more infos
@@ejunky66 okay
@@zed_one6704 thanks so much, i advice you not to use WS2812 anymore... get in touch we have way better solutions
what is the power consumption of the 2813 vs the 2812b?
thank´s for comment Each RGB LED draws approximately 50 mA when it is set to full brightness and powered at 5 V. This means that for every 30 LEDs you turn on, your LED strip could be drawing as much as 1.5 A.
Can Led run Visual effect?
hi, yes you can run everything, videos, text Animations !
Not realted to this video
But do you have any idea what does it mean when a led strip specifications says : 88D/M ??
hi, it should be 88LED/M
Nice to know
thank´s for comment mate ;)
So the moral is: if there is a stupid guy arround you and they cut your led strip you have no light anymore....
haha kind of ;) thanks for comment !
Top
thank´s for comment visit our website and join our affiliate Program, earn honest Cash with us elektric-junkys.com
4:58 for that tiny bit of info... is a waste of video time slot. Perhaps more information using texts aince you've already using them in the video anyway...
thanks for your opinion & comment mate ..
Name of soundtrack please :)?
hi guys .. have a look at the Description box the songs are Listed from start to the end .. enjoy ;) share the Vid if you Like ...
Lost in the night - Thbd
Why no voice instructions ???
because .. best regards and thanks for comment mate !
@@ejunky66 LOL.........
;) have a nice sunday mate !