The Problem with 9G Servo & How to Fix it - Creator Fix
ฝัง
- เผยแพร่เมื่อ 3 ต.ค. 2020
- The9G servos that are used worldwide by hobbyists have a problem which can be be due to 'n' reasons. The only way to fix the problem is discussed in this video.
Links in Description :
1. What are SERVOS ? : bit.ly/servo-know
2. Servo Calibration Circuit & Sketch : bit.ly/super-knob
Creator Page : bit.ly/creator-page
Creator THIS Post : bit.ly/servo-prob-post - วิทยาศาสตร์และเทคโนโลยี
Nice presentation and well thought through, useful as well. Subscribed now. Thank you, nice job.
i baught 20 micro servos and all were bad thank god i did't threw them away i will calibrate them now
Please let me know how to know the minimum and maximum values of my servo motor
Your explanation 🔥🔥🔥🔥
Great work💐
Great job bro! This made my project to work in precise...
Thanks man. Glad this helped.
Good one Pavish!!! Good to go..... Keep rocking 👍🏽😊🔥
Thank you Saranya
Thank you sooo much bro!!!
Thank you! Couldn't figure out why my sweep example was only using about 90°
Glad this helped !
Awesome 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻 thanks for the solution..
Hey Great going da pavish👍
Excellent, thank you!
Your Welcome
Hi do u hv code for multiple servo rotate at same time with different angle and different speed. Thanks for help😊
Did u get what you were searching for?
Good work da😊
Thanks da
Cool video, and I like your delivery... but man, was that extra super complicated way of seeing the turn angle xD just hold it upside down in place and mark the position at the angles you want to measure and you are done
Thanks for the suggestion 👍🏻
nice one
Hi bro, Have been testing with flysky fs i6x, ch4 able to rotate one servo, on the same channel another servo not working. tried with ch1 & ch2 with other servos not working. But using a servo tester it can be able to rotate servos.
Hi there, are you saying that your able to control one servi in a channel, but the other servis do not work in any channel?
@@PaulPavish yes , one servo works on ch4 when test with others not working on ch4 & cch1 ,ch2
Good !
I used IDE 2.0 version it fixed this issue and my problem is servo is not continuously rotating (not keep in loop) after 2 minutes servo stop rotating why it happens I don't know
Check if the servo is still powered or the pwm sweep for loops are running.
What do you say at 10:49? "That's the maximum this servo can go right now because ...?" Good video thanks
"Because I have burned the rest", means I messed up the servo's feedback/ic trying to test it beyond its range of pwm microseconds in either direction.. Happened for quite a few servos😅...Wow... U listened to that very extent in that video.. Thank you😊
My servos are rotating continuosly, as per the code it as to rotate 180 ° but they are not. Is there any solution for this? Plzs help me
Check the servo with the servo example sketch in arduino ide along with mentioned pin connections... If the servo still didn't respond, it might be the servo.
awesome bro 😎
Thanks man
I am your 300 th subscriber
Thankyou 😅
This is not really a fix... You just supplied the Servo library values you omitted the first time and thus the Servo library uses default values.
None the less, not everyone know about these "extra" arguments.
But my serwo dont move smooth it move like steps.
Reduce the time step (delay) and reduce the increment value; if both didn't work, check with a different servo. Might be that the other servos have some burned out angles.
avoid the salute
will do 👍. Thankyou for the suggestion.
Useless because they canna no speka Englis
good sir, kind sir, the thing is, its pointless....if my airplane goes at 90 degrees with just a small deflection of 24 degrees, i don't thing there is a need for my servo to go all the way 180...plus, we have this extra 20% deflection end point function in transmitters...so, what you just did was, practically of no use to the average hobbyist.....
Sure. It was meant for people who might have wondered or faced an issue regarding this. Just a share of knowledge and a possible workaround. That's all.
avrdude: ser_open(): can't set com-state for "\\.\COM3"
Failed uploading: uploading error: exit status 1
I'm getting like this what can i do
CH340 driver install it bro