How To Replace Headlight Assembly 2007-2014 Cadillac Escalade
ฝัง
- เผยแพร่เมื่อ 23 ส.ค. 2024
- Buy Now!
New Headlight Set from 1AAuto.com 1aau.to/ia/1ALH...
Over time, headlight lenses become dull and hazy. You'd be surprised how much that affects your night time visibility! Replacing your headlight assembly is an easy way to improve safety and appearance on your vehicle. This video shows you how to install new, quality, TRQ headlight assemblies on your 2007-2014 Cadillac Escalade.
• Check here for more videos on the 2007-14 Cadillac Escalade: • Cadillac Escalade 2007...
This process should be similar on the following vehicles:
2007 Cadillac Escalade
2008 Cadillac Escalade
2009 Cadillac Escalade
2010 Cadillac Escalade
2011 Cadillac Escalade
2012 Cadillac Escalade
2013 Cadillac Escalade
2014 Cadillac Escalade
Tools you will need:
• Pry Bar 1aau.to/oac/1AX...
• 10mm Socket 1aau.to/obE/1AX...
• 22mm Socket 1aau.to/ov/1AXA...
• 7mm Socket 1aau.to/obE/1AX...
• Trim Tool Set 1aau.to/oas/1AX...
• Ratchet 1aau.to/ocA/1AX...
Subscribe: / @trq
Check out our playlist:
Cadillac Escalade 2007-14 3rd Gen: • Cadillac Escalade 2007...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
I like how they edited out the struggle of getting the light assembly in and out.
That's a jump cut. Headlight doesn't slide in that easy
Thank you for the quality video, no crazy background music or annoying dribble just a high quality video with concise information.
Please note and edit this video, the lower tang (in the fenderwell) on the headlight module was reinstalled on the wrong side of it;s support bracket. The bolt was replaced and tightened against the bracket only, the headlight module support tang was behind the bracket and the lower part of the tang was bent perpendicular to the bracket by the tightening bolt. This is all quite visible if the video is watched on full screen. TRQ, you might want to retrain both your installer and video editor. IMHO
Bottom bolt was not aligned correctly
Obvious edit at point of pulling it out.
Mine was impossible without loosening bumper cover to fender attachment.
Exactly!! I had to loosen front bumper assembly.
I tried to do this following the instructions in the video but the headlight assembly will not pull out. I removed everything just like in the video. I then removed the antiquated battery tray, the windshield washer solvent bottle, loosened the bumper, grill and fender and it still won’t come out even with some gentle prying. I’m an experienced mechanic and I’ve never had such a difficult time replacing a burned out headlight. I’m about ready to break out the BFH. When you slid the headlight assembly back in you missed getting the bottom into the proper location. It went behind instead of being on the outside where the bolt could be installed so it would clamp down with the washer and hold it in place. Your bottom bolt was doing nothing to hold it, at best it would help with the alignment for the proper location.
Love the headlight aim addition at the end.
It’s a good video but it’s funny how you skip taking the headlight out and putting it back in.
Why did you cut the video at the part where the headlight actually comes out? Does it come straight out or do you tip it one way or the other? Also, how hard do you have to pull to get it out? Very disappointed I wasted my time watching this.
So why are people taking off the front bumper?
Done but I hate removing these headlights lol
So how’s the fitment? Since the video fails to show a final product.
Crazy that you just cut the hardest part out, getting the headlight out. Why??????
Looks nice where you get the grill and how much you pay
It's not as easy show how you slided out without cut in video.
BEST ViD On You Tube On The Caddie Head Lamp Removal ❤❤
Thanks for video. Its helped me.
This youtube video titled: "2008 Cadillac Escalade Ballast Completely Eliminated, Watch". This video that I made days ago, will allow you to totally Eliminate the ballast. You can also Google the title.
bro, you completely put the bottom bolt in with the headlight tab on the wrong side of the nut, lmfao wow
Why didn’t you show the full video you taking off that cover and all that extra grill pieces
Excellent
Definitely not that easy on my 2013 Escalade Platinum.
You cut the part that we probably need to see the most. If you had a hard time with it, we're going to have a hard time with it. WTH
Yall need to show the real way to do this because you have to remove the front bumper on these vehicle's