Dillon DA3000 Unboxing , Overview, Converting 223 to 300BLK
ฝัง
- เผยแพร่เมื่อ 23 ส.ค. 2024
- *NOTE: If you are setting up a DA3000 with CP2000 and plan to convert or trim 300 BLK brass, it is best to swap the swaging station to the right-hand side before installing the DA3000 crankshaft/sprocket
Full Story: bit.ly/3hj33VC
UR on RUMBLE: rumble.com/ult...
UR T-Shirts: bit.ly/2UEAkgW
UR on Patreon: / ultimatereloader
Today we’re unboxing the new Dillon DA 3000 Autodrive. We’ll combine it with the CP2000 case processing press and give you all the details as we prepare for bulk conversion of 223 brass to 300 blackout brass.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Disclaimer:
You alone are responsible for the safety of yourself and your property.
Check local and state laws before undertaking any activity involving possessing, transporting, and shooting firearms. Check local and state laws before attempting to load ammunition or perform any modifications to a firearm. Always abide by the law. Always practice gun safety.
The content on this channel (including videos, ammunition reloading data, technical data, comments, and any other information contained within) is for demonstration purposes only.
Do not attempt any of the processes or procedures shown or described in this video or on this TH-cam channel (gavintoobe).
Any reloading data supplied on this TH-cam channel (gavintoobe) or in this video, including any comments from viewers and readers must be assumed to be in error.
Always consult at least three sources of manufacturer's ammunition reloading data before reloading your own ammunition.
Do not attempt to repair or modify any firearms based on information found on this TH-cam channel or in this video.
Gunsmithing procedures should only be performed only by a licensed gunsmith.
Ultimate Reloader, LLC can not be held liable for any harm caused to any individual or any personal property related to activities, procedures, techniques, or practices described in whole or part on this TH-cam channel (gavintoobe) or in this video.
By watching this video in whole or in part, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this TH-cam channel (gavintoobe) or in this video.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Material Connection Notice:
The following Ultimate Reloader partners are featured in this video:
- Dillon Precision
Ultimate Reloader partnerships involve one or more of the following:
Product supplied for evaluation + testing + features in videos/articles, paid advertising and promotions, engineering and product development services, scientific testing and evaluation, external media production and related marketing services.
Ultimate Reloader LLC is committed to publishing subjective and data-driven information+insights related to products whether it be favorable or unfavorable or both.
For more information about Ultimate Reloader partnerships, please visit: ultimatereload...
![fellow fellow - PROUD feat. INK WARUNTORN [STRING QUARTET]](http://i.ytimg.com/vi/BQrVkMPTdHE/mqdefault.jpg)
*NOTE: If you are setting up a DA3000 with CP2000 and plan to convert or trim 300 BLK brass, it is best to swap the swaging station to the right-hand side before installing the DA3000 crankshaft/sprocket
To think about when you started your channel and to see where you are now👏👏👏 ... thanks for sharing your experience with us Brother 😉👊👍🇺🇸
Just finished loading up some Starline 300 BLK with CFE BLK and Hornadys 125’s and 150’s. You guys were right about how well CFE BLK meters
Really dirty to shoot though.
Man, your shop is a dream come true.
Really enjoyed this video. I was surprised at how fast this trimed the cases to length. Great machine and looking forward to final load and shooting of those loads.
Going first class there Gavin.
Excellent production!
I do my conversion on a 650. I have an RT1200 trimmer and a ch4d 300blk trim die. I run a dedicated trim tool head for processing. Universal deprime like you do, then into the trim die. I found the ch4d must not be forming the brass right as I had chambering issues. So I picked up a spare Lee sizing die and run that after the trim die. Zero issues once I started doing that. Can’t swage on the press, so all brass still gets run through the Super Swage after being formed. Swap my tool head over to my loading tool head and toss that converted brass back in the case feed and start loading.
Good vid! Im in the process of debugging 3 of these. Vids of the challenges you come across with indexing and breaking in would be a great topic. Get a honey badger from FFB. The bosch is a monster trimmer.
I live in Washington state Iona Dylan 750 introverted a lot 300 blackout. One thing to remember if you do a lot 300 blackout order a new cutter for your case trimmer head Tesco fast especially do thousands it’s good to have a spare
Nice
@gavin.. you are gonna want hornady lock ring or similar on those dies because as you use it there gonna walk on you. Found out many times the hard way lol. I'm sure you know that by now.. anything automated those bad boys are mandatory
I use 2in harbor freight saw with jig, rcbs small base die and trim with frankford arsenal case prep center.
Thanks, Gavin 😁
Always heard it was better to size 90% with the full length sizing die (no expander/decap pin) then finish with the trim die. Mandrel is a good idea, instead of an M die. Now you just need to get an AMP mate and install it on a Giraud trimmer.
Where would a guy find enough primers to make it worthwhile to own that thing????????????????????
As an FFL we get much better odds and first shot to purchase
@@luckyshotammunitiongunsllc2369 HUH???
Federal firearms licensed dealers can buy wholesale at places other cant.. they usually get stock befor the consumers..
@@luckyshotammunitiongunsllc2369 do you think gunsmithing worth it?
Always.. you also need an FFL for that.. or they have one for that anyway
hi, i use a dillon 1050 and a mark7 autodrive, i use for prepping my brass
Thanks for the video
It’s like watching Heisenberg set up lab equipment 😂
I just received a large package of 223/556 cases this week, It is my first time with that caliber. I am in the process of a lot cleaning and prep work on them..... i was thinking of doing half in 223/556 and the other half in 300BO. I do not own any kind of AR though. I need to get something some day.....
i can fully process any brass you want fyi
This is great when you could find the reloading supplies such as primers and powders but these days it’s still hard to find these things. I still don’t understand why primers and powders are still hard to find!!
I use a chop saw with a fancy bracket for the round... this of course WAY faster... but my setup cost ~100$ and I have done 1000s of rounds... but again not this fast lol
Great video. Curious as to how long a cutter head lasts with that much cutting. Is heat generation a concern on the cutting blade?
Sure beats my harbor freight chop saw and jig 🤣
Kinda like 1980's compared to Mark 7 machines. I would still like one though
Though everything measures fine, with a progressive IMHO it wouldn’t be a bad idea to load and fire a handful of that processed brass before you make thousands. You’d have to really like 300 blackout to make that machine pay, but if you do I’m sure it’ll be awesome.
selling converted brass will pay for this machine in no time.....but id say Dillion sent it to him....either way for his business it makes sense...
What would be a better option this Dillon or the new Genesis automation press?
I have a CP2000 with a mark 7 autodrive
shoulda went mark7 drive.. i run 2 dillon drives and 4 mark7 drives and would NOT get another dillon drive again
Which one do you prefer? The M7 or the Dillon?
WE RUN 14- MARK 7 , 5 WITH CP2000 ON THEM,2 ON 1100 AND 7 REVS AND 1 AMMO BOT. WE ARE A DILLON DEALER I THINK THEY MISS THE MARK ON THE 3000.NO WAY WOULD I REPLACE A MARK 7 DRIVE FOR THE DA3000
Any chance of a comparison (pro/cons) between the Mk7 and DA3000 without...ahem...getting any blowback?
Anyone know what expander mandrel and size being used
Gavin, how is the finished edge after trimming? Is chamfering required?
Of course it is required. Everbody seems to forget it
I thought the trimmer did it.
thats wow! l have 1050 that's good nuff, gunoil here.
If i send you my 5.56 brass, will you convert it for me for a fee?
Check out 300 HAM'R!
Its no wonder no one can find any primers!!
I'm confused... swedging after decaping makes no sense... did I miss understand?
Yes- you misunderstood. You can’t swage with a spent primer in place :)
Why don't people just buy 300BLK brass haha, such an expensive endeavour to save some cents per case on 300.
We will be converting THOUSANDS of these :)
He is an FFL07. The license allows him to load and sell commercially if he chooses. Automated is the only way to make money as a commercial loader/reloader.
😀👍‼️
сколько стоит такое чудо техники?
💰💰💰💰💰
I can buy about 4 lifetimes of prepped brass for what these 2 machines cost. Interesting to watch, but no way in hell am I spending thousands of dollars just to make brass.
nice but expensive
🤤