Throttle Body Cleaning - Nissan Micra
ฝัง
- เผยแพร่เมื่อ 14 ก.ค. 2022
- How to remove, clean and replace the throttle body on a 2003 to 2010 Nissan Micra K12 with 1.0, 1.2 and 1.4 liter petrol engines. The O-ring part number is 16175AX000. If you need to calibrate the throttle body you use the method in this video: • Throttle Body Calibrat...
Thanks for watching. Please comment, like and subscribe !.
~~~~ Part Links ~~~~
As an Amazon Associate I earn from qualifying purchases.
Throttle Body ~ amzn.to/3OjBw0Z
Throttle Cleaner ~ amzn.to/3BfqJ4K
Fluid Drain Pan ~ amzn.to/3yZe0At
Disclaimer: Screwsnutsandbolts is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to www.amazon.co.uk
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2023
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts. - ยานยนต์และพาหนะ
If you need to calibrate the throttle body, watch this video: th-cam.com/video/ZGwqOl7osi4/w-d-xo.html
Thanks for watching my video. If you found this or any of my other videos helpful, maybe you could consider supporting my channel by using the ‘♡ Thanks’ button below each of my videos. Your support would be greatly appreciated, thank you ! 👍
Screwsnutsandbolts
thanks man. one of the most informative micra k12 vids
You're welcome, thanks for watching !
Thanks again. Useful information to know.
You're very welcome !
Thank you. Like your video's!
Thank you too!
Cheers mate. I may actually attempt to do it myself now!
Thanks for watching !
Just bought one. It needs touch. Your videos are class! Thank you very much man!
You're very welcome, thanks for watching !
Thanks so much good clear video
You're welcome !
I wonder why the air intake snorkle have that hole and the bulb at top... Is it to create some sort of vortex to avoid moist or particles geting in to the filter and going up the bulb? I removed mine and the car ran better.
Hey pal, nice video!
Can i ask you something? Could you please make a complete video about replacing the TIMING BELT and CLUTCH from a PEUGEOT 206? Using the same vehicld you have?. I really need it!
Thanks. I don't have the 206 any more, sorry.
Could a dirty throttle body cause excessive fuel consumption and higher idling? My K12 1400 idles at about 1500 and comes down to the lowest of about 1000-1100rpm. I have replaced MAP sensor as Diag showed it was faulty and car was heavy on fuel (16L/100km). Car computer currently gives fuel consumption at 12,7L/100km for town driving. BTW love your informative channel as I've only had my K12 for about 5 months now and very helpful to see how the car works.
Thanks for watching. A dirty throttle body could possibly cause higher fuel consumption and/or high idle but so could many other issues. It's probably worth checking the throttle plate to see if it's dirty.
Good day sir, what is the purpose of that 2 screw on the side of the throttle body? Is that for adjustment? Thank you
I think their the idle adjuster screws.
Have any video about outlet gaskit change
I don't, sorry
Getting p3000 multiple cylinder misfire. Changed spark plugs and cleaned throttle body as per video. Noticed my throttle body flap is slightly open, is this normal?
Car stalled yesterday and wouldn't start, flooded engine.
Any ideas? Thanks.
When you turn the key to the 'on' position, whithout starting the engine, can you hear the throttle body motor moving the flap ?
Would it not be abvisable to disconnect the battery ? Will this aleviate the need to perform a throttle body relearn ? After carefully following your instructions, this is the position I find myself in. Regards
You could disconnect the battery and it will relearn after you reconnect it and drive for a while if you prefer not to carry out the throttle learning procedure. It might just take a bit longer.
@@screwsnutsandbolts Thanks
Can I use ultrasonic cleaner to do this job?
Just covering the metal parts, not top half black electronics.
I wouldn't advise doing that
@@screwsnutsandbolts ok. Thanks
I have followed each step an cleaned my K12 Micra trottle body and map sensor. After running the engine i get a check engine light. When i drove it down 500 meters down the neighbourhood i noticed that the idling was bad too. Break pedal was softening up at some moments. Do you make relearning of the trottle body and map sensor after the clean up?
No I didn't need to relearn the throttle or map sensor after cleaning them. I don't know how this cleaning could affect your brakes ?
The first hose disconnected is the brake servo hose - could that have any relevance? To learn the closed throttle body position you’re supposed to turn the ignition on for 10s then off for at least 10s, but then you also have a few more learning steps for the idle and accelerator positions.
Ahh you're right. It might not be reconnected properly, or leaking somewhere
@@screwsnutsandbolts It turned out the trottle body needs relearning. My micra is the K12E automatic version. I drove it to a shop and they did a computer relearning. Everything is fine now. I would appreciate if you make a video and show how to replace the aerial console.
That's good news. I hope to get around to doing the aerial some stage soon if I can.
Hi, do the throttle valve positions need to be recalibrated after the cleaning?
You can calibrate the throttle using this method: th-cam.com/video/ZGwqOl7osi4/w-d-xo.html
@@screwsnutsandboltsThank you
You're welcome
My 2005 K12 (1.4 automatic) won't always start, and sometimes it starts and cuts off a split second later. If I do get it going it works fine throughout the journey. I have an engine light and the diagnostic device said P0340 Camshaft position sessor. I've changed both Crankshaft and Map sensors but no luck.
Could it be the throttle body that needs cleaning? Or something else?
It could be the wiring to the camshaft sensor is damaged or possibly the timing chain could be stretched among other things. Is there high mileage on the car ?
@@screwsnutsandbolts Thanks for your response, the mileage is 89k, the problem came on suddenly. Going to clean the throttle body to see if that helps.
Let me know if that helps
@@screwsnutsandbolts Turns out the new Crankshaft sensor I bought was dodgy, I got another one and the problem is fixed, i'm really glad it's not the timing chain and thanks for your response.
However, I now have an air leak and need to inspect all the pipes, I've been advised to check the vacuum hose ...Not sure which one that it, is the vacuum hose one pipe or is it referred to more than one pipe? I understand it's linked to the breaking system and my car did rev up when I'm breaking to stop at a junction (and then cuts off). Your input will be greatly appreciated.
Btw, not driving the vehicle to prevent further damage.
I have a problem with a 2006 Nissan Note 1.4. 226,342 km. In the morning, my car shuts off when I start. Then I stop it for a while, the car starts and drives all day.
Does anyone have any advice. They gave spark plugs or should I clean the throttle valve.
thank you
If you open the bonnet and turn the ignition key to the 'on' position can you hear the throttle body motor activating ?. It's usually a high pitch followed by a clicking sound
1:56 what sensor is that?
That's the EVAP purge valve solenoid: th-cam.com/video/zBWi9J1rWHE/w-d-xo.html
How can i change the throttle position sensor have problem with that 😔
The TPS is integral with this throttle body so you'll probably have to swap the entire throttle body unit.
Hi, Where can I buy O-ring? 9:15
The original part number is 16175AX000. If you search for that you should be able to find one on ebay or amazon
Oring code ? Thanks
The original part number is 16175AX000
This is definitely not k11 micra , could you please specify body model in the title?
It's all in the video description