Laser Duct Fan Upgrade | AC Infinity A6

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 18

  • @pcvanvliet
    @pcvanvliet 10 หลายเดือนก่อน +1

    Looking good Jerry, good airquality is important in your makerspace when you spend a lot of time there.

  • @mikedoyle5362
    @mikedoyle5362 10 หลายเดือนก่อน +1

    Great start! Always good to have a laugh!

  • @mikedoyle5362
    @mikedoyle5362 10 หลายเดือนก่อน +1

    Really like the ac infinity. I use the 6in hose up until the last 5 in and have a reducer for 6 to 4.

  • @LSEngraving
    @LSEngraving 10 หลายเดือนก่อน +1

    Looking good Jerry as always I love that unboxing knife

  • @KRich408
    @KRich408 10 หลายเดือนก่อน +2

    I might upgrade the Hon&Guan 130 CFM it's Junk for my Roly 20w , I just etched a bunch of mirrors today. my basement smells like a plastic factory.

    • @3DHP
      @3DHP  10 หลายเดือนก่อน +1

      Well that's no good.You don't want to be breathing in anything that might have harmful chemicals in it.

  • @mikedoyle5362
    @mikedoyle5362 10 หลายเดือนก่อน +2

    Do you use a window to vent

    • @3DHP
      @3DHP  10 หลายเดือนก่อน +4

      lol,,you didn't watch the video.

  • @chrislmink
    @chrislmink 10 หลายเดือนก่อน +1

    Make sure you keep that back door locked if you have a waste gate open it sticks out past the door when open lol. I didnt think it was that loud at all.

    • @3DHP
      @3DHP  10 หลายเดือนก่อน +1

      It easily turns at the Y. Thought about when I screwed to the wall.Louder than the smaller one,but ok.

  • @BLUEMOONENTERPRISES
    @BLUEMOONENTERPRISES 10 หลายเดือนก่อน +1

    When you removed the fan, were you able to continue to use the same exit fitting minus the fan to attach the hose? Was it difficult to remove the fan? My Lasermatic should arrive soon and I'm trying to sort out an exhaust for it, which is going to be very similar to yours. Thanks.

    • @3DHP
      @3DHP  10 หลายเดือนก่อน

      I just used shorter bolts and put the duct back on. Once you unplug fan,wire with connector will slide out of the aluminum channel,no reason to try and pry it off.Its very easy to do.I also left the fan screen on the inside.

    • @BLUEMOONENTERPRISES
      @BLUEMOONENTERPRISES 10 หลายเดือนก่อน +1

      @@3DHP Thanks! Great explanation!

  • @mgl_angel0542
    @mgl_angel0542 4 หลายเดือนก่อน +1

    Great System set up! 🫡

  • @TheLouisianaHobbyGuy
    @TheLouisianaHobbyGuy 10 หลายเดือนก่อน +2

    I had one of these, and it seemed the only settings that worked were the last two. Should just be High/Low.

  • @KRich408
    @KRich408 9 หลายเดือนก่อน +1

    I just purchased this fan its great! 👍 im still trying to figure out how to remove the factory fan without cutting the wires or damage the condit or orange plastic? The fans cord won't fit through the Condit Roly used.

    • @3DHP
      @3DHP  9 หลายเดือนก่อน +1

      Unclip the fan,the wire is like 6 inches long.Do not remove the silver metal duct.The wire and connector will slide through it.Then use shorter bolts for duct with grate. Save fan and screws,if you ever sell it,you can put back to stock.

    • @KRich408
      @KRich408 9 หลายเดือนก่อน +1

      @@3DHP ok thanks 👍👍👍👍👍