DHANYAWAAD SIR JI AAPNE BEST JAANKARI DI.SIR HUM IS MODULE KE INPUT MAIN MAXIMUM KITANE VOLT AUR AMP DE SAKTE HAI.AUR SIR KYA YEH 4 VOLT KI BATTERY KO CHARGE KAREGA.PLEASE BATAYE.
@@sumitnarkhede.3105 4v ki battery bhi charge karna chahiye. Maine Kiya nahin ha lekin shayad Voltage ki setting 4v ke anusaar setting karne par ho jaayega Aapko video pasand aaya uske liye Dhanyvaad.
Relay not working probably, like tik-kit -tik because reaching voltage 14.30v cut supply and when supply cut voltage go down 13.60v so again on the charging relay this process is continue 😂😂😂😂😂 Sounds like tirrrrrrrrr tirrrrrrrr😂😂😂😂❤
Hello. nice video, well explained. Can you tell me, please, what are the adjustment limits of this circuit? I would like the relay to connect at a voltage of 13.5 volts and disconnect at 16-17 volts. I want this because I want to use it for an application with a car. When the engine is off, the battery has approximately 12-12.5 V. After starting the engine, the voltage increases because the alternator starts charging and when 13.5 volts are reached, the relay will engage. The upper value of 17 volts is chosen so that the relay remains connected as long as the engine is running, because in fact under normal conditions this value of 17V cannot be reached with an alternator in a 12V car. After you stop the engine, the value of the battery will drop below the cut-off threshold of the relay. This is what I would like to do... do you think that the circuit falls within these limits?
When connected with battery and the battery discharges and drains to 9volts then the led on the pcb glows but relay doesn't work due to 9v. Under this situation what can be the solution.
@@CSTech2024🙏🙏🙏🙏 Sir, please tell me how to get this output using the same module xh m601... Relay OFF when car battery voltage is from 0V to 13V. Relay ON when battery voltage is from 13.1V to 15V.
Can I get the reverse output as mentioned below??? Simply as.... Relay should be OFF when car battery voltage is from 0V to 13V. Relay ON when battery voltage is from 13.1V to 15V. Please help how to achieve this output.😊
Yes u can try this as the relay's another one path connected when relay is off and it disconnected when relay powered on By setting lower 13v and upper 15v When voltage between 0-13 that another path as I said is disconnected and the main charging path is connected as the relay is on and when voltage>13 the relay goes of and that another path will connected. I mean basically relays have two switches and everytime one of them is conductive
This video was very helpful! I have power cut off module and input source switcher in one module! Slightly different in structure of this one... Plz can you make a video for my module? I don't know how adjust it! Kindly share your email address, i will send you pictures and instruction guide! Plz adjust it for me.
Wate of money. Don't use this. If you don't keep ac on , this circuit consumes heavy power and finally battery will be discharged below recovering point. Also you cannot use less amps power supply
Tnx vaiya.... module ta onek age kinesilam...... setup korte parini ......aap ka video dekh kar hogaya.....tnx
Excellent, thank you !! 👍
🙂Welcome !!
it is a very good video. thank you very much you should good luck.
Thank you so much.
DHANYAWAAD SIR JI AAPNE BEST JAANKARI DI.SIR HUM IS MODULE KE INPUT MAIN MAXIMUM KITANE VOLT AUR AMP DE SAKTE HAI.AUR SIR KYA YEH 4 VOLT KI BATTERY KO CHARGE KAREGA.PLEASE BATAYE.
@@sumitnarkhede.3105 4v ki battery bhi charge karna chahiye. Maine Kiya nahin ha lekin shayad Voltage ki setting 4v ke anusaar setting karne par ho jaayega
Aapko video pasand aaya uske liye Dhanyvaad.
@@CSTech2024 DHANYAWAAD SIR JI.
Very nice video sir
Thank you so much.
Thanks vaiya
Relay not working probably, like tik-kit -tik because reaching voltage 14.30v cut supply and when supply cut voltage go down 13.60v so again on the charging relay this process is continue 😂😂😂😂😂
Sounds like tirrrrrrrrr tirrrrrrrr😂😂😂😂❤
Solar panel se connect kar sakte hai kya
@@ramtilwani3904 Yes
input is DC or AC?
The charging input is AC given to the battery charger.
When I can connect the divices to use the batery at rhe same time?
You can connect the charger and battery as well together.
Can it be used for 20v 3.5 or4.7 amp in put what will be a period of the module.
Can I charge a Gel Battery with this?
I cannot understand the Gel Battery but as per my experience, any type of batteries can be connected.
@CSTech2024 thanks
Is it possible to do the settings without using dc to dc buck converter if so then please reply
Thanks for watching video. Actually for calibration, we need a variable power supply. We can use 317 based variable power supply also.
@@CSTech2024 Pls suggest battery or any other method as buying a dc to dc converter increases the cost
We can use 317 based variable power supply also in place of dc to dc converter
Hello. nice video, well explained. Can you tell me, please, what are the adjustment limits of this circuit? I would like the relay to connect at a voltage of 13.5 volts and disconnect at 16-17 volts. I want this because I want to use it for an application with a car. When the engine is off, the battery has approximately 12-12.5 V. After starting the engine, the voltage increases because the alternator starts charging and when 13.5 volts are reached, the relay will engage. The upper value of 17 volts is chosen so that the relay remains connected as long as the engine is running, because in fact under normal conditions this value of 17V cannot be reached with an alternator in a 12V car. After you stop the engine, the value of the battery will drop below the cut-off threshold of the relay. This is what I would like to do... do you think that the circuit falls within these limits?
Thank you so much sir. I will try to solve your problem. Till now I used this setup in my home with 7AH battery only.
When connected with battery and the battery discharges and drains to 9volts then the led on the pcb glows but relay doesn't work due to 9v. Under this situation what can be the solution.
We can set the minimum charging voltage to a little bit higher so that the relay can be operated.
@@CSTech2024🙏🙏🙏🙏 Sir, please tell me how to get this output using the same module xh m601...
Relay OFF when car battery voltage is from 0V to 13V.
Relay ON when battery voltage is from 13.1V to 15V.
555ic jeat while using charger why??
Battery charger contotler module circuit diagram ?
I purchased the module online. Don't have the circuit diagram.
Can I get the reverse output as mentioned below???
Simply as....
Relay should be OFF when car battery voltage is from 0V to 13V.
Relay ON when battery voltage is from 13.1V to 15V.
Please help how to achieve this output.😊
Yes u can try this as the relay's another one path connected when relay is off and it disconnected when relay powered on
By setting lower 13v and upper 15v
When voltage between 0-13 that another path as I said is disconnected and the main charging path is connected as the relay is on and when voltage>13 the relay goes of and that another path will connected.
I mean basically relays have two switches and everytime one of them is conductive
How use it with DC input (From solar 12v) ,not using 220v ac charger please reply
Got any ideas ?
@@gauravsinghsays nope, it's worthless
Last steps led off nehi ho raha hai , anti clock wise ghumakar last tak jane ke bad bhi
An ACDC fan can be run with this circuit
It depends upon your battery, not upon the module.
Nickel Cadmium Battery Charging and discharging procedure and connection diagram
how buy
You can buy from robu.in
Ye circuit maine without 555ic ke bina banaya hai 3 relay ko use karke😂🤣🤣
Circuit Diagram?
Hi, thanks for watching the video.
xh m601 module can be purchased online. The setup circuit is already given in video.
Low voltage 12v need to on pcb below 12v. Please prepaid video sir
Thanks for watching the video sir.
Please clarify your message. I am unable to understand.
अरे संदीप भाई शिक्षा देने वाला वीडियो मे बैकग्राउंड म्यूजिक नहीं दिया जाता है. इस से समझने मे कठिनाई होती है
धन्यवाद भाई। आगे से इस बात का ध्यान रखूंगा।
Music ki awaz tu band kar do
Next video men...
This video was very helpful! I have power cut off module and input source switcher in one module! Slightly different in structure of this one... Plz can you make a video for my module? I don't know how adjust it!
Kindly share your email address, i will send you pictures and instruction guide! Plz adjust it for me.
Sorry for answering too late. My email - sandeep.upa@gmail.com
It is not so good module .
Wate of money. Don't use this. If you don't keep ac on , this circuit consumes heavy power and finally battery will be discharged below recovering point. Also you cannot use less amps power supply
Yes, you are correct. This is not for heavy load.
Wate don't buy