Nice video Albert and ordered a couple of those after I saw it. Tested it today after a month waiting. Works with Syma X8GH flight board with the new X5 protocol. Bare in mind if you assign SwD for throttle hold and move ch1 or 2 stick will trigger the flip mode. Also you could limit the lower end point on the throttle (ch3) to 85% so it wont cut the motors off in mid-flight just as it does with the Syma controller when hold it down for 3 seconds. Adjusting the exponential curve also gives you quite precise moves. Nice kit overall, range would be a concern but in Ireland, where I am, regulations forbid flying unregistered UAV more than 300m away and 15m high, which doesn't really bother me as we're just buzzing around the back yard with the kids. Learned the hard way bringing X8 for landing from a hight can be a bit of a challenge sometimes. Well, comes down really quick if you hold the throttle down for 3 sec :-)
I’ve heard you use the term “toy” a couple of times... does it only work with the small transmitters of the micro quads? Or does it work well with a, let’s say spectrum receiver as well?
@@thelongranger55no, I mean how to connect the power from the tx to the module. Do you solder it to a specific pad on the board or just straight to the battery?
Hey Albert, what flight times do you get with your E010 w Fpv cam ? Thinking of getting the more pwrful E011, adding the eachine Tx01 and the range multi protocol module as well.
Hi. My multiprotocol module (i use with Flysky i6x) not connected to Eachine e010? Why? But i good condition to Floureon H101. For contacting to Eachine e010 use this combination: left and right stick move to position down+right and power up . Please help me.
Hi Thanks for your reply. Followed your video but cant get the light to go green after setting as arming list not sure why? Using Eachine i6 Don't get green light on irange x irx6 tx module. When battery is connected.
Albert Kim, do you know if this works with the cx stars? After watching your video I odered one as well as a cx10 older version and a hard to find dhd d1 which I believe is the same as the cx stars. However in the list I see the dhd d1 and the fx 10 no mention of the cx stars?
I have a question. How do you trim the quad if it drifts to a certain direction just like its toy transmitter? Also, have you tried flipping or is there a way to assign a flip and roll button? Thanks
I have a doubt, I bought the multiprotocol and the eachine e011, it worked very well, suddenly I stopped synchronizing the flysky and the original transmitter , the dron turns on the led fast when detects the transmitter but does not finish synchronizing, you know which could be the mistake, thank you, excuse my English
ok looks good do you put the tx on a unused model or will it mess up a configured model? also will the i6 store each 1r6x bound quad? or do you have to bind each quad every time you want to fly it? thanks
do you have to keep the battery plugged into the module at all times while flying or just for the binding process? if so how long does a battery last on a single charge? thank you
Hi Albert, I just bought the JJRC pro T1 mini quadcopter and also have the IrangeX transmittter. Do you think that this little module should fix my bind problem as well?
Albert Kim thanks. One last question, I also have a Furibee F36 that I tried to bind, is it not the same as the E010? Of course in the process the module stopped lighting up at all so now I think it might have a problem.
I got a B03 Pro and E011 for Christmas and am having a ball flying with a real transmitter. Do you find that using this setup decreases the Range? It’s a pretty tiny antenna.
Thanks for nice video, up and running I6 and module. Question on Bayang and H8 mini, they both work with module. Flip is setup on channel 6, that works. I set channel five to a 2 position switch for rates, however, does not seem to support, no rate change, I looked at many threads and have not found how you control rates if possible. Tnx in advance
I got one purchased Sep 09 2017 and it works with i6s. And you even do not need external battery when used with i6s if you bridge two pads. Module comes with instruction sheet where all of this is explained. Too bad Bangood do not have this manual sheet for download.
My i6s has a trainer port, but there seems to be some mis-information around if this module works, depending on which radio you have. Do you know a way to tell if the module will work?
Do you have to change anything in rx settings like the ppm on/off? Also does switching between AFHDS or AFHDS2 make a difference? The one I ordered does not power on consistently, does yours? It will work for a couple flights then stop working, a couple days later it might work again. I have tried different batteries and checked all connections and it looks fine. I can't trust it so I just bought another one.
Bound my i range 7 up to my Syma x11 (with flysky TX) but the pitch is way deeper fwds than back, like its flying backwards almost. The instructions say make sure its AETR order. How do you input that on your transmitter ?
It's iRangeX iRX6 I watched your review and noted your paper addressing how to bind many different models. I'm not sure if the paper comes with the part. Does it? Thanks for your time.
Hello Albert I purchased one of these modules and am able to bind it to my e010 and my x11 but when I give it too much right stick in any direction they do a flip. Any suggestions?
Albert Kim yea, can't really find any info anywhere, only one banggood comment that said its working. But i might check the board inside the TX for a 3.3V pin, one YT video said that there are some and try to power from that. Cause i think the banggood description says that only to tell us to use a 1S lipo
@@AlbertKimTV hello and thank you for getting back to me. Much appreciated. Sorry I mean what position do I need to move the gimbles in order to activate the v761 protocol? Thank you.
Albert Kim Do you mean some models will respond to expo changes and others won't? Why? Is it how the firmware was written or is it a piece of hardware on the board? How can I tell before I buy a model or can I ? Sorry for all the questions, I am slow when it comes to this stuff. You have been so helpful with your rad vids thanks a million man.
It depends on what protocol those toys are using. That is sometimes hard to determine. This particular module is somewhat limited. I think this one will have more model support... bit.ly/2SHRd8F
@@AlbertKimTV thanks man, but the irange6x and flysky 6 channels dont have module bays do they? Making a decision on transmitter today. The TX's are starting to pile up..lol. Plus I want to do some PNP/BNF stuff. I'm addicted. All fix wing so far. Picked up the Xk A100 based on your review for beginners, as well as the XK a800 and sky king 959..lol. Maybe I should just get the jumper t8sg?
depends on the model. usually channel 5/6 do those things. You'll need to consult the RCgroups thread with your specific model ... someone might know over there.
Salut.... J'ai le fsi6, le irangex IRX6, et aucunes connections, idem avec n'importe quel autres types de drones... 😳😳☹️☹️☹️ Je respecte les diverses manips, et.... RIEN.... 😭😭😭😭 J'ai maj la radio en 10 voies, est ce cela qui beug ?? J'espère trouver de l'aide, svp.. Marci
Hello! I connected the E010 to my FS-i6X equipment, through the iRX6 module. The equipment has a new model "3" with the output signal PPM. And it doesn’t work for me correctly. That turns the motors, then no. Tell me, maybe there are some other settings? Thanks! drive.google.com/file/d/1eLeeuWImHyvYW26UeWcKCTMmyujomKRa/view?usp=sharing
Hi Albert, can I use this to bind my Flysky to a Devo RX2637H-D receiver? The Devo receiver came installed on my Walkera Master CP heli, and now I dont have the Devo 7E transmitter. But I do have the Flysky one. Could you please help.
the range has now been extended dramatically by doing this mod. on a E011 range increased from 30m to 275m www.rcgroups.com/forums/showthread.php?2905531-iRangeX-iRX6-Multiprotocol-TX-Module-for-Flysky-FS-i6-i6x-Transmitter-FREE-TEST/page8#post39102851
Nice video Albert and ordered a couple of those after I saw it. Tested it today after a month waiting. Works with Syma X8GH flight board with the new X5 protocol. Bare in mind if you assign SwD for throttle hold and move ch1 or 2 stick will trigger the flip mode. Also you could limit the lower end point on the throttle (ch3) to 85% so it wont cut the motors off in mid-flight just as it does with the Syma controller when hold it down for 3 seconds. Adjusting the exponential curve also gives you quite precise moves. Nice kit overall, range would be a concern but in Ireland, where I am, regulations forbid flying unregistered UAV more than 300m away and 15m high, which doesn't really bother me as we're just buzzing around the back yard with the kids. Learned the hard way bringing X8 for landing from a hight can be a bit of a challenge sometimes. Well, comes down really quick if you hold the throttle down for 3 sec :-)
solution of the year for micro quad toys. great!!
I’ve heard you use the term “toy” a couple of times... does it only work with the small transmitters of the micro quads? Or does it work well with a, let’s say spectrum receiver as well?
Hey Albert Kim, thanks for the review! Will you possibly do a review on the Hawkeye Firefly 7s? It looks like a great camera, I am saving to get one!
It is a great camera! I reviewed it about a year ago... th-cam.com/video/HGJFh4b4nB4/w-d-xo.html
@@thelongranger55 Could you please explain how you connect the module to the tx?
@@thelongranger55no, I mean how to connect the power from the tx to the module. Do you solder it to a specific pad on the board or just straight to the battery?
@@thelongranger55 I see. Thank you very much
Hi, did you notice an increase range using that transmitter compare to the stock toy transmitter?
not really
hey albert i just saw you on andyrc's channel but i have one question do you still use the diatone crusader gt2 200
+just drew yes still use.and have it
Hey Albert, what flight times do you get with your E010 w Fpv cam ? Thinking of getting the more pwrful E011, adding the eachine Tx01 and the range multi protocol module as well.
Does this use your flysky's antennas or is there an antenna built on this chip? Thanks for the video!
+Matt Jones antenna on chip
Very good. Does it also work with the FS-i6S radio? Thankful.
I don't think the i6S has the same port on the back so it won't work.
Hi. My multiprotocol module (i use with Flysky i6x) not connected to Eachine e010? Why? But i good condition to Floureon H101. For contacting to Eachine e010 use this combination: left and right stick move to position down+right and power up . Please help me.
Hi Thanks for your reply. Followed your video but cant get the light to go green after setting as arming list not sure why?
Using Eachine i6 Don't get green light on irange x irx6 tx module. When battery is connected.
Which light? What drone? Which transmitter? Need a lot more info... kinda lost with what you gave....
Sorry new to this. I am using a Eachine i6 Not getting green light on the irange x irx6 Module after powering with battery
Albert Kim, do you know if this works with the cx stars? After watching your video I odered one as well as a cx10 older version and a hard to find dhd d1 which I believe is the same as the cx stars. However in the list I see the dhd d1 and the fx 10 no mention of the cx stars?
Your tx says i6x but u say it doesnt work with module i want to connect. Bo3 pro which tx do i need fs i6 or. Thanks
I have a question. How do you trim the quad if it drifts to a certain direction just like its toy transmitter? Also, have you tried flipping or is there a way to assign a flip and roll button? Thanks
I have a doubt, I bought the multiprotocol and the eachine e011, it worked very well, suddenly I stopped synchronizing the flysky and the original transmitter , the dron turns on the led fast when detects the transmitter but does not finish synchronizing, you know which could be the mistake, thank you, excuse my English
Sorry, I'm not sure. Perhaps the order of the bind sequence it incorrect. Try switching the order around and see if it makes a difference.
maybe I'll try, thank you very much
ok looks good
do you put the tx on a unused model or will it mess up a configured model?
also will the i6 store each 1r6x bound quad? or do you have to bind each quad
every time you want to fly it?
thanks
The i6 is just a dumb interface... it doesn't store anything from the multiprotocol module. You have to rebind for every model.
do you have to keep the battery plugged into the module at all times while flying or just for the binding process? if so how long does a battery last on a single charge? thank you
battery must stay plugged in
Hi, I have Fs-i6 and just bought a quad with DSM2 integrated receiver - will this module bind to DSM2 or I have look for another solution?
This one doesn't have DSM2. You'll need to find something else however, I'm not aware of anything that will do DSM2 and work with the FS-i6 radio.
@@AlbertKimTV Thanks for quick response and confirming :)
Hey Albert, I don't have one of the newer FlySky radios, but I do have an old T6 and a 9x. Would this work with either of those?
+Tsnafu does it have the same trainer port?
Hi Albert, I just bought the JJRC pro T1 mini quadcopter and also have the IrangeX transmittter. Do you think that this little module should fix my bind problem as well?
Nice review, went ahead and go one. Wondering if it will work for the Boldclash B03? Did not see that on the list.
B03 Pro will work. B03 has centered throttle, so not sure that one will work.
Albert Kim thanks for the reply. Yeah I’m figuring that out seeing other vids about the non-pro. Does it use the Bayang protocol?
+Dean Hallal yes bayang
Albert Kim thanks. One last question, I also have a Furibee F36 that I tried to bind, is it not the same as the E010? Of course in the process the module stopped lighting up at all so now I think it might have a problem.
I got a B03 Pro and E011 for Christmas and am having a ball flying with a real transmitter. Do you find that using this setup decreases the Range? It’s a pretty tiny antenna.
Great video thank you. One question. What rate will it be in? How do you change from the slow to fast rate? Or can you even do that?
+Dale Jump Jr. It depends on the model it varies greatly so experimentation will be required.
Albert Kim ok thanks..will try to figure it out when it comes in.
Do you know if this will control the JJRC 37 elfie? I hate flight controlling with a phone
Hi kim what is the name of the battery that you used for the module and where did you buy it
battery is here - bit.ly/3ehUlR0
Will this multi-protocol work with the mjx bugs 3 drone and for my FlySky i6s
Thanks for nice video, up and running I6 and module. Question on Bayang and H8 mini, they both work with module. Flip is setup on channel 6, that works. I set channel five to a 2 position switch for rates, however, does not seem to support, no rate change, I looked at many threads and have not found how you control rates if possible. Tnx in advance
How would this work with the different modes and so on?
Hi Albert Do you know if this will work with the Eachine i6 transmitter ?
Yes, it will.
Everyone uses that transmiter. Im assuming not for the FS-I6s?
+Mark does not work for i6s
Albert Kim thanks was I was hoping it would work also
I got one purchased Sep 09 2017 and it works with i6s. And you even do not need external battery when used with i6s if you bridge two pads. Module comes with instruction sheet where all of this is explained. Too bad Bangood do not have this manual sheet for download.
My i6s has a trainer port, but there seems to be some mis-information around if this module works, depending on which radio you have. Do you know a way to tell if the module will work?
What difference between fs i6 and fs i6x? And can It bind with every toy drones like syma x5?
i6X doesn't work with the multiprotocol module. This module does not bind with everything. List is discussed in the video.
Albert Kim ah ha! I found it thankyou..I didnt know it!
@@AlbertKimTV if i6x doesn't work if this multiprotocol....whats another option for i6x able to bind with eachine010 or jjrc h36?...please advice tq
Do you have to change anything in rx settings like the ppm on/off? Also does switching between AFHDS or AFHDS2 make a difference? The one I ordered does not power on consistently, does yours? It will work for a couple flights then stop working, a couple days later it might work again. I have tried different batteries and checked all connections and it looks fine. I can't trust it so I just bought another one.
+DroneXFun I didn't have to change any settings... I'm also not having the power issue you are describing. Sounds like yours might be defective.
If the buy the fa i6 radio and install that module and bind it is it ready to fly or needs programming? and can you change rates?
Bound my i range 7 up to my Syma x11 (with flysky TX) but the pitch is way deeper fwds than back, like its flying backwards almost. The instructions say make sure its AETR order. How do you input that on your transmitter ?
Those instructions are referring to the OpenTX version which this one is not. I think your issue is something else but I'm not sure what it is.
OK, would reversing any of the channels help at all ?
It's iRangeX iRX6 I watched your review and noted your paper addressing how to bind many different models. I'm not sure if the paper comes with the part.
Does it? Thanks for your time.
I think it should. I'm not sure if this is still sold anymore.
Hello Albert
I purchased one of these modules and am able to bind it to my e010 and my x11 but when I give it too much right stick in any direction they do a flip.
Any suggestions?
The channel for flips is active. You need to reverse that channel in the radio.
Thankyou Albert
Hello Albert
Im somewhat new to RC and the problem you helped me with turned out to be a broken three way switch on my tx
thank you again
Do these instructions come with the iRangeX?
Which iRangeX?
I sont have to use a lipo and can just solder it to the 5V of the controller right?
According to the specs the max voltage is 4.2v so 5v might fry it.
Albert Kim yea, can't really find any info anywhere, only one banggood comment that said its working. But i might check the board inside the TX for a 3.3V pin, one YT video said that there are some and try to power from that. Cause i think the banggood description says that only to tell us to use a 1S lipo
@Ruxys Have you tried/fried it? :)
Pokornz oh no, i ended up using a 18650 batterry from and old laptop. Which has the same voltage as a 1s lipo
Does this work for bayang protocol?can I use this for betafpv 65s lite?
Hi. Can i use iRangeX for syma x5c board?
Yes
This so helpful for me!
The module includes the battery or you have to buy it?
Thank you for your video much appreciated.
Do you know the stick configuration for the Eachine V761 protocol?
Thank you.
All the details are on the website here... www.multi-module.org/using-the-module/protocol-details/v761
@@AlbertKimTV hello and thank you for getting back to me. Much appreciated.
Sorry I mean what position do I need to move the gimbles in order to activate the v761 protocol?
Thank you.
hey does work with frsky receiver and other stuff or just micro quads
This one is just for the toys
Will adjusting expos have an effect? I put ch1 and ch2 expo at 50 but I'm not sure if there is difference. Thanks for sharing.
It depends on the model.
Albert Kim Do you mean some models will respond to expo changes and others won't? Why? Is it how the firmware was written or is it a piece of hardware on the board? How can I tell before I buy a model or can I ? Sorry for all the questions, I am slow when it comes to this stuff. You have been so helpful with your rad vids thanks a million man.
Can the iRangeX iRX6 Multiprotocol Module be made to work with the FuriBee F36?
I think that's a clone of the E010? I'd ask over in the RCgroups thread to make sure.
Mine already upgraded to 10 channel, can I use this irx6? Thanks
could you tell me if it is compatible with Realacc R11, please?
Not sure. I think the protocol on the R11 is proprietary. You may want to go ask in the RCgroups forum.
hi, i have a jjrc h67 santa claus, i can not connect it. How should I do?
Use the Bayangtoys protocol.
Albert Kim ,it's not the same, can you explain the procedure well?
The white model with blue props in the video uses the same protocol as the H67. Just duplicate what I did in the video and it will bind.
Hey man, thanks for these great reviews. Will support and buy from your links. Will this module work with fixed wing toys as well?
It depends on what protocol those toys are using. That is sometimes hard to determine. This particular module is somewhat limited. I think this one will have more model support... bit.ly/2SHRd8F
@@AlbertKimTV thanks man, but the irange6x and flysky 6 channels dont have module bays do they? Making a decision on transmitter today. The TX's are starting to pile up..lol. Plus I want to do some PNP/BNF stuff. I'm addicted. All fix wing so far. Picked up the Xk A100 based on your review for beginners, as well as the XK a800 and sky king 959..lol.
Maybe I should just get the jumper t8sg?
Are you able to change rates of the E010 with the Flysky transmitter? I want a E010, but only if I can throw the stock transmitter in the garbage lol.
+osheathedj yes
Thanks! Enough range for backyard fun? 50 meters?
+osheathedj i think 50m is OK
cool! I think a E010 or E011 is in my future.
currently having issues with this module and flysky fs-i6s, by my understanding it should work, a search find one working and one not. any ideas?
Sorry, I have no idea... maybe make sure your model is setup to work in PPM mode?
Hey I tried binding it to my e011 & it won't bind.
Have the same problem !! does not work, light not blink.. I have the i6 10 channels mod, maybe that's why ?
Choose another model in the i6 settings!
Do you think I can use this for the maker fire blue shark?
IDK
Can we bind syma x8g with this protocol
What about the Furibee F36?
+SubatomicMD I don't know what that is, sorry
Same thing as the E010 but made by Furibee with better motors
+SubatomicMD the E010 protocol should work
Will it work on the eachine e013?
I don't think it will.
Albert Kim ok, thank you
wow- TYVM
Bro how can I get a lay out sheet like that to do my binding for my toy drones
PDF file download on the product page?
Don't understand how do I download the list I don't have the item so I was thinking can u sen me a link please
Good Morning. Does it work with Eachine e013? thankful.
AFAIK it does not.
Hi I'm not getting mine connected to my hubsan x4 107c
Does anyone know if the unit works with an echine e013 small pepper
it does not currently but might in the future with a firmware upgrade... check the RCgroups thread for more info.
How to change speed level and acro mode??
depends on the model. usually channel 5/6 do those things. You'll need to consult the RCgroups thread with your specific model ... someone might know over there.
Thank a lot bro. One more question. Does the module use the signal from the remote antenna? Or the module have own antenna?? Sorry for my bad english.
hi, what is the range?
How about the range?
+Fikri Khoirurohman limited to indoors ... not very far
Salut....
J'ai le fsi6, le irangex IRX6, et aucunes connections, idem avec n'importe quel autres types de drones... 😳😳☹️☹️☹️
Je respecte les diverses manips, et.... RIEN.... 😭😭😭😭
J'ai maj la radio en 10 voies, est ce cela qui beug ?? J'espère trouver de l'aide, svp.. Marci
Can i use this to bind flysky transmitter to frsky receiver
Not this one... you need a 4-in-1 but none are made for Flysky radios.
@@AlbertKimTV is there any ways to use a flysky radios?
@@AlbertKimTV because in my country frsky transmitter is not available
@@AlbertKimTV Can i use any multiprotocol module to use FRSKY receiver and using flysky radios?how about Irangex IrangeX6
The problem is, usually when i have new model my old one broken for no reason.
Batery 7v ?
does anyone know if this works with the newer E013?
Did yo find a way to bind to the E013?
This will work with the bugs6 ?
I don't think it will
@@AlbertKimTV tnx Albert
Hello! I connected the E010 to my FS-i6X equipment, through the iRX6 module. The equipment has a new model "3" with the output signal PPM. And it doesn’t work for me correctly. That turns the motors, then no. Tell me, maybe there are some other settings? Thanks!
drive.google.com/file/d/1eLeeuWImHyvYW26UeWcKCTMmyujomKRa/view?usp=sharing
Hi Albert, can I use this to bind my Flysky to a Devo RX2637H-D receiver? The Devo receiver came installed on my Walkera Master CP heli, and now I dont have the Devo 7E transmitter. But I do have the Flysky one. Could you please help.
Sorry, I don't know anything about that receiver.
can you bind traxxas link 2.4 ghz receiver with IrangerX multi protocol module
Sorry, I don't know but you can check out the website to do your own research... www.multi-module.org/
If only it could do DSM2!!!
FYI - github.com/goebish/nrf24_multipro , the source code...
the range has now been extended dramatically by doing this mod.
on a E011 range increased from 30m to 275m
www.rcgroups.com/forums/showthread.php?2905531-iRangeX-iRX6-Multiprotocol-TX-Module-for-Flysky-FS-i6-i6x-Transmitter-FREE-TEST/page8#post39102851