This is really amazing!! Thanks for showing us how to build that little transformer... I hope I'm lucky and find an old computer source of my own! :) A question I have, though... I have exactly what I need at the exit: 35.0.35, but how powerful this is? In watts, I mean...
Hi dear I did all the steps according to the video. But the 3300 micro capacitor in the negative line gets very hot and bursts. Is the direction of the 9-turn coil correct? Shouldn't both be wrapped in one side? please help me to fix this problem. thanks
@@dhtproject7022 I found the circuit fault. The negative line uses a common anode diode and I mistakenly used a common cathode. The project is very good. thank you
use two transistor seld oscillating ccfl inverter to drive transformer and drop ic of ka3525. change and add windings to output windings of ccfl inverter for output voltages you need
Çok güzel ama devre şeması nerede? Devre şeması olmadan bir işe yaramaz ki video? En azından el ile devre şeması çizip açıklama bölümünden paylaşsanız olmaz mı?
@@dhtproject7022 Tekrar çizip açıklama kısmında link olarak paylaşamaz mısınız? Güzel olmuş devre çünkü ama şema yok, parça isimleri yok. Bu haliyle çok işlevsiz olmuş.
@@dhtproject7022 eu adorei esse projeto eu fiz ele e coloquei pra funcionar meu amplificador e fiz uma caixa de som para eu levar para a praia e ficou muito bom
can some one please explain to me induction coil turns and polarity how is it calculated? The problem starts whe I use HV cenemic capacitors on me E core type ignition coil I take multipel 3kw ceramic capacitors and solder them together 1 side of capacitor goes to + ignition coil terminal the other side I ground out to baterry negative terminal. Evry thing is fine and great starter motor turns faster who I like be the way ,smuther engine ,brighter lights but there is tiny problem that acured And that problem has some thing to do with the delco 12 si alternator it opel car from the 80s some where some how its constantly back chargeing true the alternator light I noticed diode is bypassed true the engine warning light unless I rev me engine to around 3-4000 rpm then the light go off and alternator charges baterry. So I hoppe peopel understand me here me problem capacitor types and their voltage farad rating has some thing to do with alternator starting charge rpm this alternator that I have is around 1000-1200rpm starts to charge but when I add those hv ceramic capacitors the starting charge icreasing meaning I need higher engine rpm to charge baterrys . Baterry voltage fluctuate around 15.5 volts and climes litel on higher rpm 16-17v the baterry oddly enough doesnt seam to be bothered be it . The baterry actualy holding charge longer when car does not work for longer time. So can some one explain to me how do I stop alternator to interact with that capacitor? Are there some ground potential stabiliser circuets? Dual charge systems ? What can I do to programe that alternators starting charge if indead capacitors can manipulate its rpm range . Im with out kiding totaly confused . And out of curiosety watched lot peopel use automotive dual 5 pin relays they culd latch,change polarity and what not it look to me nearly identical functions like the delco 12si voltage regulator . The original voltage regulator has only 1 ic chip inside and 1 singel small capacitor . So for years I have problems finding corect circuet that can prevent external circuets to interact with baterry and alternator. If some one has similar circuet please share how that look like wire shematic .
thanks for sharing this project... im not an electronics but i want this circuit for my tda8954th class d amplifier... uhm, by the way... how much is the input capacity...? can i use 17v as its source?
Hi Friend! sorry for the long wait. This circuit has a capacity of ~150-200w. please wait patiently, we are designing a 110v/220v to (+/- 30v ) - (+/-60v) converter circuit. Thanks a lot!
@@dhtproject7022 thanks for the reply... i have a plan to make this project... i have here a 220v to (+/- 17v) transformer... can i use this transformer as my input source for this build...?
Es la primera vez que aprendo tanto en un solo video, felicidades y gracias !! 🥳🎉
If I want to use an EE 42 ferrite, what gauge should I use in the primary and secondary, thank you
Exit, full sine or square sine, which one. If it is a square sine, there will be noise and static sound in car amplifiers.
This is really amazing!! Thanks for showing us how to build that little transformer... I hope I'm lucky and find an old computer source of my own! :) A question I have, though... I have exactly what I need at the exit: 35.0.35, but how powerful this is? In watts, I mean...
Super exelint great information
Hi Friend! Thank you very much!
Very nice and very good and beautiful
Hi Friend! Thank you very much!
Very nice video
J'adore ce que vous faites 👍
Quel est le nom du logiciel que vous utilisez pour faire les circuits imprimés ?
Muito bom!
Great, thank you! Can you suggest some manufactured module which will do the same from 12v to 20v 2-5A? Thanks
Sar muze 100+100what car tep banana hai bass trabel bhi chalana hain chal payega Ripley pliz
thanks for this great stepup but is there any chance for the circuit diagram for it please i will be very great ful to u keep it up always
Hello, my friend! I regret drawing the PCB without a Schematic
Sir pdf file rar dika raha hai
@@dhtproject7022 I think your mean was Forget not regret.
سلام من این مدار بستم ولی اون مولتی ترن عمل نمیکنه ولتاژ خروجی ثابته
Hi dear
I did all the steps according to the video. But the 3300 micro capacitor in the negative line gets very hot and bursts. Is the direction of the 9-turn coil correct? Shouldn't both be wrapped in one side? please help me to fix this problem. thanks
Hi Bro! How many volts are you using?
@@dhtproject7022 I found the circuit fault. The negative line uses a common anode diode and I mistakenly used a common cathode. The project is very good. thank you
@@invisibleman6330Help me where is the mistake, I am also in the process of making this
use two transistor seld oscillating ccfl inverter to drive transformer and drop ic of ka3525. change and add windings to output windings of ccfl inverter for output voltages you need
nice project
👍👍👍
Çok güzel ama devre şeması nerede? Devre şeması olmadan bir işe yaramaz ki video? En azından el ile devre şeması çizip açıklama bölümünden paylaşsanız olmaz mı?
PCB'yi devre şeması olmadan çizdim.
@@dhtproject7022 Tekrar çizip açıklama kısmında link olarak paylaşamaz mısınız? Güzel olmuş devre çünkü ama şema yok, parça isimleri yok. Bu haliyle çok işlevsiz olmuş.
Dear SiS,
IC right side all resistors are 10K?
❣️❣️❣️❣️
eu gostei muito parabéns
obrigada!
@@dhtproject7022 eu adorei esse projeto eu fiz ele e coloquei pra funcionar meu amplificador e fiz uma caixa de som para eu levar para a praia e ficou muito bom
@@FabioJunior-bn6pz vc tem o esquema elétrico
🎂💝🌷thank you v m
Kolay gelsin
Teşekkürler! iyi şanslar
Top
Ok thank you
جميل ♥
❤️
Where's the daigram
Do you have trhe schematics?
Could you share it?
Atx transformar frequency???? Khz????
❤❤❤❤
can some one please explain to me induction coil turns and polarity how is it calculated?
The problem starts whe I use HV cenemic capacitors on me E core type ignition coil I take multipel 3kw ceramic capacitors and solder them together 1 side of capacitor goes to + ignition coil terminal the other side I ground out to baterry negative terminal.
Evry thing is fine and great starter motor turns faster who I like be the way ,smuther engine ,brighter lights but there is tiny problem that acured
And that problem has some thing to do with the delco 12 si alternator it opel car from the 80s some where some how its constantly back chargeing true the alternator light I noticed diode is bypassed true the engine warning light unless I rev me engine to around 3-4000 rpm then the light go off and alternator charges baterry.
So I hoppe peopel understand me here me problem capacitor types and their voltage farad rating has some thing to do with alternator starting charge rpm this alternator that I have is around 1000-1200rpm starts to charge but when I add those hv ceramic capacitors the starting charge icreasing meaning I need higher engine rpm to charge baterrys .
Baterry voltage fluctuate around 15.5 volts and climes litel on higher rpm 16-17v the baterry oddly enough doesnt seam to be bothered be it .
The baterry actualy holding charge longer when car does not work for longer time.
So can some one explain to me how do I stop alternator to interact with that capacitor? Are there some ground potential stabiliser circuets?
Dual charge systems ?
What can I do to programe that alternators starting charge if indead capacitors can manipulate its rpm range .
Im with out kiding totaly confused .
And out of curiosety watched lot peopel use automotive dual 5 pin relays they culd latch,change polarity and what not it look to me nearly identical functions like the delco 12si voltage regulator .
The original voltage regulator has only 1 ic chip inside and 1 singel small capacitor .
So for years I have problems finding corect circuet that can prevent external circuets to interact with baterry and alternator.
If some one has similar circuet please share how that look like wire shematic .
thanks for sharing this project... im not an electronics but i want this circuit for my tda8954th class d amplifier... uhm, by the way... how much is the input capacity...? can i use 17v as its source?
Hi Friend! sorry for the long wait. This circuit has a capacity of ~150-200w. please wait patiently, we are designing a 110v/220v to (+/- 30v ) - (+/-60v) converter circuit. Thanks a lot!
@@dhtproject7022 thanks for the reply... i have a plan to make this project... i have here a 220v to (+/- 17v) transformer... can i use this transformer as my input source for this build...?
if you already have a transformer you can rebuild it by removing the 17v coil and rewinding the new coil +/- 35v without this circuitry
you need to determine your transformer capacity. If the power is not enough, you cannot use it
@@dhtproject7022 thanks a lot friend... but i need this circuit to boost my 12v DC... ☺️☺️
Gostei vou fazer um
Hay
👌👌👌👍👍👍🙏🙏
i can,t undrestand pcb file 😐plz give me full curcuit diagram plz 🙏i need this curcuit only jpg file link send full diagram 🥺
sorry. I just draw PCB. I don't use Schematic
ohh its ok 😊 thank you dear god bless you
Ingeniero buenos días sí quisiera subir un poco más el voltaje a 40 a 45 voltios qué haría
Necesita aumentar el número de vueltas en la bobina secundaria. y ajustar la resistencia de retroalimentación
@@dhtproject7022 gracias por la respuesta
Disculpa cuál sería la resistencia de retroalimentación aumentaría yo su valor o la bajaría gracias
Pwmnya yang pakai 7500 atau tl494 kak
7500 dengan tl494 itu bisa saling menggantikan
your circuit diagram is wrong on output diode...please check...its make Xplosion capacitor if anyone build...😅😂
Sar muze car tep and tractor ke liye banana hai pliz Ripley
haan main ek naya veediyo banaoonga!
How to increase its ampere.
Hi Friend! sorry for the long wait. You can add more mosfets and with bigger transformer. Thank you very much!
Possible 12v to 18v 10A?
Hi! you need to change the number of turns of the secondary coil. and feedback resistor
❤Sir componits details or pdf file
Hai ,dimana saya dapat membelinya
Hai. Anda bisa melakukannya sendiri. Download yang saya lampirkan ada di deskripsi.
Sir pagawa po ako power supply 12v to 70 v asap po sir
Sir pdf file rar dika raha hai
fir se upload kardo pdf file
Sar 0.7mm swg geas batao pliz
Hi Bro! 22swg ~ 0.7mm
Sar ye kitne amp ka hain
Load kitna chalana hain
ما هوا رمز المقاومه المرموزه برقم 10فقط
باید چکار کنم
Plz PDF
Hi Friend! You can find the attachment in the description
Pbc size bro
how i can make boost converter 12v to 180 volt 10 amper
you need to increase the number of MOSFETs and the capacity of the transformer. you also need to change the turn ratio of the secondary
Hi , instead of battery (12 volts 8 amps ) can I use ATX POWER SUPPLY ( 12 VOLTS ,15 AMPS) as input??
Yes
Top
Hay
Please make SMPS that makes +45 0 - 45 for using it in Audio amplifier circuits thank you.
Winding lng nmn idagdag jan. Sa output imbes 9 0 9 turns 12 0 12 turns gawin mo
Hola. No puedo descargar el diagrama. Por favor una ayuda
Ragang kristian
Eufg ti aakan aantakan
لو سمحت كم تتحمل امبير الدائره
واريد عمل دائره 60 فولت و25 امبير
هذه الدائرة 300 واط فقط. تحتاج 1.5kw؟
اريد منك دائره تتحمل 25 امبير
Sar chapper nahi mila to konsa lagau
sir miron kayung diagram yan..
Excellent.
In this smps we can replace the capacitor and put 50 bolt 10000mah
Hi Friend! Sorry for the long wait. Please carefully check the discharge current of the battery .Thank you very much!
❤❤❤
Parabéns muito bom
❤️❤️❤️
You hindi speaking im pakistani but i do undrestand hindi 🙃 but litle
Can,t open pdf plz can you give me facebook or whatsap number 🤔
Hi. I used google translate to answer you guys.
Por favor podria darme pcb y diagrama...gracias
Hola. ¡Puedes encontrar el archivo de descarga en la descripción del video! ¡buena suerte!
😀
Make switch mode power supply with all data and details
Hi my friend!
@@dhtproject7022 hi
Có bị sụt áp khi có tải k ạ
có hồi tiếp nên không tụt đâu ạ
Sar apki pdf opan nahi ho rahi hai
नमस्कार भाइयों! आप पीडीएफ फाइल खोलने के लिए एडोब रीडर या फॉक्सिट रीडर का उपयोग कर सकते हैं
Ausome
Hi bro
Sar kitna what's ka bord chala sakte hai pliz Ripley
kshama karen, mujhe samajh mein nahin aaya ki aapaka kya matalab hai
@@dhtproject7022 ये पूछ रहे हैं इस पावर सपलाई पर कितने वाट का ऐँपलीफायर बोर्ड चला सकते हैं।
me podrías compartir archivos gerber para hacer lapcb, gracias un saludo
Hi. +-45v to +-50v how many turns and maximum power
Toujours au sommet super ★
♥️
سلام. عالی بود
Please aisy link mat share kiya Karen Jo open hi na hoty ho
Can you share the circuit diagram
Can you share the circuit diagram and pcb
Circuit diagram
Hi Friend! You can find the attachment in the description