Nice video guys, I just bought myself a M21 to swap out my th350. So its nice to see all the parts I'll need to swap the Muncie into my 68 Camaro. Thanks for the video, keep up the good work!
one trick I use to install the trans easier is take 2 aprox 6 inch bolts same size as trans to bell housing cut off hex head and install in bell one top one bottom diagonally they become guide pins .
it's easy .i did it to a 69 camaro when i was 17 years old. that is a 4spd car already . Automatic cars you have to cut a hole in the floor pan for the shifter
I know the power handling from engine to trans will be wrong but can I put an 83 Firebird 5 speed in a 69 camaro ? The camaro has a 327 and the Firebird is a 5.0 . Thanks guys a great video !
Should bolt up ok. We always check the top of the bell housing as some Pontiac transmissions don’t follow the Chevrolet small block shape at the top of the bell housing near the distributor. But that transmission isn’t super stout.
The process would be very similar, but of course the parts would be different. I think 77 is still using a three speed automatic, so a 4 speed should bolt upwards to the crossmember and utilize the same drive line. You would need. Correct? Shifter, linkage, pedals brackets and linkage. Sounds like a fun project!
We no longer have a part number but it was a NAPA part. You can try application but I believe it is a generic/ cut and bend your own length if I remember. It was very easy to do. Cut 1/2 inch short then with needle nose round a hook on the end cut.
Nice video guys, I just bought myself a M21 to swap out my th350. So its nice to see all the parts I'll need to swap the Muncie into my 68 Camaro. Thanks for the video, keep up the good work!
You are very welcome. Thank you for watching and good luck with the conversion.
Glad to hear your health is better. Looking forward to your videos
Just did this swap out myself. Can't wait to take it out and lay down some rubber
Awesome. Manual is so much fun
one trick I use to install the trans easier is take 2 aprox 6 inch bolts same size as trans to bell housing cut off hex head and install in bell one top one bottom diagonally they become guide pins .
Genius!! I’m going to put that to use
Great tip on upping your insurance. Just did that myself actually and next I swap my 2 speed Powerglide for my new TKX. Thank you for the guidance!
Our pleasure. Thanks for hanging out with us!
it's easy .i did it to a 69 camaro when i was 17 years old. that is a 4spd car already . Automatic cars you have to cut a hole in the floor pan for the shifter
I have a 67 Camaro I wanna convert as well however it’s going to be a T56 with a hydraulic clutch
How about keeping your car numbers matching? More value.
It wasn’t numbers matching in the first place.
awesome video!
Great video thanks for sharing! Do you know if this would be relevant for a second gen Camaro, specifically a 75? Thanks.
Thanks for the question. For the most part yes. The parts are not interchangeable of course but the theory is and everything should be pretty close.
I know the power handling from engine to trans will be wrong but can I put an 83 Firebird 5 speed in a 69 camaro ? The camaro has a 327 and the Firebird is a 5.0 . Thanks guys a great video !
Should bolt up ok. We always check the top of the bell housing as some Pontiac transmissions don’t follow the Chevrolet small block shape at the top of the bell housing near the distributor. But that transmission isn’t super stout.
Cool Vid !
Would this apply to a 77 Camaro probably not I’m just wondering if it would be a similar process?
The process would be very similar, but of course the parts would be different. I think 77 is still using a three speed automatic, so a 4 speed should bolt upwards to the crossmember and utilize the same drive line. You would need. Correct? Shifter, linkage, pedals brackets and linkage. Sounds like a fun project!
What clutch fork spring did you use ? Can you tell me where you got it and a part number ?
Thank you
We no longer have a part number but it was a NAPA part. You can try application but I believe it is a generic/ cut and bend your own length if I remember. It was very easy to do. Cut 1/2 inch short then with needle nose round a hook on the end cut.
@@thegaragefathers496 Thank you
Trans fluid? Would the crossmember on a Turbo 400 Camaro work with this swap?
No the 400 transmission rear mount is further back. It uses the same frame mounting holes but won’t line up to a th350, power glide or 4spd.
What kind of transmission 4 speed is this a muncie ?
Yes, a Muncie M-20
I have so many questions is it possible to contact you via email? Or some other way