DYS Motor Vs Standard Motor | Extreme Thrust Test | Max Power

แชร์
ฝัง
  • เผยแพร่เมื่อ 6 ก.พ. 2023
  • This video is all about the thrust test of the DYS Motor of the G Series. I am using a 1000 KV as well as 1700 KV motor and comparing its thrust with the specification chart.I have tested these motor with 8-inch and 10-inch propellers. I have also tested a 1000kv brushless motor with a 10-inch and an 8-inch propeller and compared the three of them.
    I have also designed and made a Test rig. The best part of it is that we can test different motors on it.
    Watch this informative video, especially the conclusion part.
    There's so much to understand in this video.
    Thank you and have a nice day.
    Help me guys in reaching 20 K subscribers :-)
    For downloading the Test rig 3D Printing files, visit the below link :
    themechninja.com/product/moto...
    Apparatus used in the video:-
    M3 Allen nuts and bolts :- IND - amzn.to/3sA0sb7
    USA - amzn.to/3y29ij1
    Watt meter:- IND - amzn.to/3swB6em
    USA - amzn.to/3y3ZiFS
    Pulley :- IND - amzn.to/37WqqMF
    USA - amzn.to/2WaJkN0
    Spring balance :- IND - amzn.to/3gjkDFi
    USA - amzn.to/3B2LxcF
    Servo Tester :- IND - amzn.to/3B0YAuT
    USA - amzn.to/3j1svgl
    11.1 Volt battery :- IND - amzn.to/3tvaaLB
    USA - amzn.to/3zm0mXy
  • วิทยาศาสตร์และเทคโนโลยี

ความคิดเห็น • 53

  • @dronepilot260rc
    @dronepilot260rc ปีที่แล้ว +1

    Keep up the good work my friend! 🎉

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Thankyou so much 😊😊

  • @experimentaldiaries
    @experimentaldiaries ปีที่แล้ว +2

    Great work 🎉

    • @MechNinja
      @MechNinja  ปีที่แล้ว +1

      Thankyou so much for watching the video...
      Don't forget to subscribe 😊😊😊😊

  • @mohammedzeyton
    @mohammedzeyton 5 หลายเดือนก่อน +2

    Hard to understand the English but otherwise Awesome work ! nice editing ! good effort ! very nice explanation too ! you earned a subscribe :)

    • @MechNinja
      @MechNinja  5 หลายเดือนก่อน

      Thanks for watching...do check my new videos too....

    • @mohammedzeyton
      @mohammedzeyton 5 หลายเดือนก่อน

      @@MechNinja of course !

  • @andreyl2705
    @andreyl2705 ปีที่แล้ว +1

    nice work

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Thankyou so much....
      Don't forget to check out my other videos too....
      And don't forget to subscribe 😊😊😊😊

  • @mohammedfahad6563
    @mohammedfahad6563 5 วันที่ผ่านมา

    Bro. Dys motor shaft mm how much? 3.17 or 3 mm. Is there any difference between 3.17 mm and 3 mm. Bcz i want to buy a deill check for this motor. But in drill chuck size is 3:17 mm. Can i fix that on 3 mm dys motor!

  • @karandeepsingh8498
    @karandeepsingh8498 ปีที่แล้ว +1

    Great comparison, great video ✨️, so asking for suggestion could these dys motors be used on a quad copter whose weight should not exceed 2 kg, and has abilities to drop payload of 200 gm, making minor project so need some suggestions, also it is autonomous system, so should this could be used on the quad, flying time is atleast 20 min, also is there any specific size of motor that should be used on quad like is 2215 onlu used, as thi 30 series is heavy weight, give suggestions bro.

    • @MechNinja
      @MechNinja  ปีที่แล้ว +1

      Well you can go with this dys motors....infact these are efficient too.
      It has a good thrust...even you can make a drone of up to 4000 gm. The point is time of flight. For exact time of flight use the charts which I have provided you in the video..
      Then you can calculate it.
      And thankyou for watching the video and don't forget to subscribe 😊😊😊😊

    • @karandeepsingh8498
      @karandeepsingh8498 ปีที่แล้ว +1

      @@MechNinja thanks a lot bro, just one more doubt does the weight of the motor effects the performance?

  • @robertsmith2956
    @robertsmith2956 ปีที่แล้ว +1

    How out of balance are the blades after removing the support?
    What about a 5 bladed fan?
    Won't you need a few ducts in the nose cap to let air get to the cooling ports?

    • @MechNinja
      @MechNinja  ปีที่แล้ว +1

      Yes sir they were out of balance a little because the connector provide by the company were actually friction fit.
      If they have provided us with screw connectors and hence the distance between the propeller and the motor will be short and there will be little to no vibration.
      I have to made a 5 blade fan.... Infact i have tested it with an 11 blade fan. You can check my latest videos. it's in there...
      Since I am using a propeller hence there is lots of space to enter the cooling ports.
      Hope i have answered all your questions.
      So thankyou for watching and don't forget to subscribe 😊😊😊😊

  • @mixkoora246
    @mixkoora246 9 หลายเดือนก่อน +2

    I want a link to a website to purchase the motor

  • @Allrounder77860
    @Allrounder77860 ปีที่แล้ว +1

    Good thrust brother

  • @Arya_Putra_1
    @Arya_Putra_1 ปีที่แล้ว +1

    bhai jo specifications and observations k saath video bnate ho , that is really awesome
    bhai ye propellers cheap rate m kaha milenge ? any idea

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Robu.in

    • @MechNinja
      @MechNinja  ปีที่แล้ว +1

      Bhai subscribe kar lena.....

    • @Arya_Putra_1
      @Arya_Putra_1 ปีที่แล้ว

      @@MechNinja done ;)

  • @billionaireyt6504
    @billionaireyt6504 10 หลายเดือนก่อน +2

    Can i use 30 ampere esc with standard 1000kv Motor? Will it be safe?🤔 And also which size of propeller will be best for standard 1000 kv motor?

    • @MechNinja
      @MechNinja  10 หลายเดือนก่อน +1

      Yes you can use a 20 amp ESC....and use 10 inch 1045 propeller with it....
      And thankyou for watching and don't forget to subscribe 😊😊😊😊

  • @riteshpatil6104
    @riteshpatil6104 3 หลายเดือนก่อน +1

    Bro can I use this motor for my rc boat which have small propeller of 60mm diameter, will it give the same thrust or different?

    • @MechNinja
      @MechNinja  3 หลายเดือนก่อน

      For smaller propellers choose a high kV motor

  • @muahmadansari7391
    @muahmadansari7391 3 หลายเดือนก่อน

    dys d 2836 750kv bldc motor thrust test. With 1045 and 8045 propeller plz..

  • @sainirchobby
    @sainirchobby 10 หลายเดือนก่อน +2

    Brother use small diameter propeller with higher KV motor👍 7-8 inch propeller.

    • @MechNinja
      @MechNinja  10 หลายเดือนก่อน

      Bro check my previous videos...I have used a smaller propeller with high Kv, here the recommended propeller was 10 inch so I have used it.
      Thankyou for your suggestion.....and thankyou for watching and don't forget to subscribe 😊😊😊

  • @loodwich
    @loodwich ปีที่แล้ว +3

    Your efficiency has units "gm/Wats," but I don use that as efficiency, I call it "trust/power".
    To measure the efficiency, I compare the "Mechanical power/Electrical power"
    To measure the Mechanical power, I measured the wind velocity of the propeller in m/s and multiply by the Trust in Newton, so my efficiency doesn't have units. I only compare the electrical motors with the power that they could produce.

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Thankyou so much sir for your valuable comments and you are definitely right about the efficiency formula.
      But In my case i generally use the data which are easily available in the market. Mostly motors and EDF company has labelled thrust to power ratio as efficiency in their specifications chart. So i also took this data so that people can easily compare my EDF with the market one.
      Theoretically you are correct but I write to make it easier for my viewers.
      Hope you understand sir.
      And thankyou for watching it and pls don't forget to subscribe 😊😊😊😊

    • @loodwich
      @loodwich ปีที่แล้ว

      ​@@MechNinja I am already subscribed to your Channel since this video. I saw your chapters on ducted fans, and I was happy that you started again.
      I check a lot of motors and propellers because now I live in Ecuador at 2300 m above sea level ... I can use 2205 2300 KV with a 7-inch propeller...
      I am trying to understand which data is clearer to write a research paper on that subject... and it is horrible; I started to find a lot of data, but what is essential or not. So your tests are very exemplary to me.

  • @martales8563
    @martales8563 ปีที่แล้ว +1

    still waiting for the counter rotating edf , com on man dont skip it

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Don't worry brother....😅😅
      I have already uploaded it...but not released yet.......
      I will be available in this week.....😊😊😊
      Thankyou for watching the videos

  • @gym_wale
    @gym_wale 5 หลายเดือนก่อน

    should i use this motor in my battle bot? actually i am finding high toque motor with high rpm the stall torque should be like 3-4kg-cm nd stall rpm should be like 3000rpm.for power i'm using 12v 20amp battery{it could be increased}.i want 2 motors to rotate drum{wepon} weighted aproximate 200gm with the help of pully mechanism.

    • @gym_wale
      @gym_wale 5 หลายเดือนก่อน +1

      earlier i was looking for Rs-895 brushed motor but i'm hasitating bcz brushed motor have low efficiency

    • @MechNinja
      @MechNinja  5 หลายเดือนก่อน

      I am not sure about the torque but the rpm is very high i.e. kV*volts of the battery.
      These motor can go upto 15000rpm
      And since you will be using pulley , so there will be more chances of slipping at this much rpm.
      Generally In my college days I too used a high rpm DC motor. If you have money then you can try both of them....

    • @gym_wale
      @gym_wale 5 หลายเดือนก่อน

      @@MechNinja would u suggest any motor!? With average rpm and high torque..

    • @gym_wale
      @gym_wale 5 หลายเดือนก่อน

      @@MechNinja money is the whole reason why I don't want fully fail experiment.did have any motor any mind or any friend of yours who know abt this it would be great help!😊

  • @mpikas
    @mpikas 4 หลายเดือนก่อน

    Your 220g to lift the arm is not accurate for the second motor, which is smaller and lighter decreasing the weight of the arm, I'm guessing that 190g is probably the correct value for that considering the motor weight (that will change slightly depending on the angle of the arm)

  • @ashutoshmishra2113
    @ashutoshmishra2113 ปีที่แล้ว +1

    can you suggest a motor which can generate 1700 g of thrust

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Well I can suggest you....but could you first tell .me the application of it....so that I can provide you a better one

    • @ashutoshmishra2113
      @ashutoshmishra2113 ปีที่แล้ว

      @@MechNinja we want to carry approximately 1000g of weight

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      And what will be the total weight of the drone excluding the payload

  • @gstar8325
    @gstar8325 ปีที่แล้ว +1

    Can I use 30a esc with dys 1000kv motor ?

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Actually I don't think so...because I think the minimum ESC required is of 50 amps... I am not sure...but I have shared the chart in the video....you can watch it from there

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      And thankyou for watching this video and don't forget to subscribe 😊😊😊😊

    • @gstar8325
      @gstar8325 ปีที่แล้ว +1

      I watched the video , there it consumed 25a so I asked

    • @MechNinja
      @MechNinja  ปีที่แล้ว

      Ok then you can go for it....but please check it charts also for recommendations.....
      Because currently i have used wattmeter to check it..but since you won't be using it

    • @TimFuzail
      @TimFuzail 9 หลายเดือนก่อน +1

      please note that the motor is rated for ~12A use, if the motor is consuming more than that for anymore than few seconds, it'll probably melt it's inside plastics