У меня проблема с датчиками, при расстоянии от 300 мм до 780мм и 840-2000мм всё хорошо, но при расстоянии 780-840мм начинает светиться датчик красным, и показания на экране сбрасывается на значение 31мм. Как настроить? Есть ощущение, что это как мертвая зона. И датчик считает что объект слишком близко. UC4000-30GM-IUR2-V15
Hello. How to make ultrasonic sensor synchronization connections for internal synchronisation for UB500? Do I just connect idividual synchronisation wires together?
Hello nixth3x, the following synchronization modes are possible: 1. Several sensors (max. number see technical data) can be synchronized together by interconnecting their respective synchronization inputs. In this case, each sensor alternately transmits ultrasonic pulses in a self multiplexing mode. No two sensors will transmit pulses at the same time (see note below). 2. Multiple sensors can be controlled by the same external synchronization signal. In this mode, the sensors are triggered in parallel and are synchronized by a common external synchronization pulse. 3. A separate synchronization pulse can be sent to each individual sensor. In this mode, the sensors operate in external multiplex mode (see note below). 4. A high level (+UB) on the synchronization input switches the sensor to standby mode. Note: Sensor response times will increase proportionally to the number of sensors that are in the synchronization string. This is a result of the multiplexing of the ultrasonic transmit and receive signal and the resulting increase in the measurement cycle time. We hope you've found this information useful. You can view this information on our datasheet for the UB500-18GM75-E5-V15 here www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=15010 or if you have further questions, please visit us here www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm. Thank you.
Buenas tardes Eduardo, le comento que el sensor mencionado se configura meramente con los botones que tiene integrados. Con gusto comparto el documento PDF en Español que explica el procedimiento, éste es corto: files.pepperl-fuchs.com/webcat/navi/productInfo/pds/111686_spa.pdf?v=20220103160732 . De cualquier forma si tiene más dudas sugerimos escriba al mail jpayan@mx.pepperl-fuchs.com si necesita soporte técnico en Español. Saludos.
Hello Kaatni, we're here to help. Our customer service agents and technical support specialists are ready to answer your questions and help you get the information you need. Please fill out our Ask an Expert form by clicking this link here: www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm
Hi there Khawaja Naeem. You need to use the Ultrasonic sensor UC6000-30GM70-2E2R2-V15 www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=51811#software ULTRA-PROG-IR software in order to change those settings. The software can be found on the product page under the software tab. If you don't already have the cable, you will need it in order to interface the sensor with the computer you are using. The cable can be found at the bottom of the “Associated Products” tab. Interface cable UC-PROG-IR-USB www.pepperl-fuchs.com/usa/en/classid_190.htm?view=productdetails&prodid=69497. We hope this helps!
Hi there Venkatesh, you can program the sensor via the push-buttons on the unit itself. You may need to program the A1 (near) and A2 (far) points along with the rising ramp. You can find these steps on the datasheet that can be obtained in the link below, starting on page 4. UB2000-F42-I-V15 www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=24959
Hi there Panwi AHPL, please review our datasheet for the UC6000-30GM-IUR2-V15 here: files.pepperl-fuchs.com/webcat/navi/productInfo/pds/104095_eng.pdf?v=20210524185045 Please review the "programming" section that begins on page 5, if you need further assistance please visit our website and fill out our Ask An Expert form www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm. Thank you.
Hello Irwan, We're here to help. Please fill out the Ask an Expert form so we can assist by clicking the link below. www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm Thank you.
Hello Sama Vibes, the following link will provide the installation instructions for the UB2000-F42-E6-V15. files.pepperl-fuchs.com/webcat/navi/productInfo/45/451492b.pdf?v=20200312072512 More information can be found on the product page of the UB2000-F42-E6-V15.” www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=24957 We hope this is helpful to you.
Nice way of explanation, Thanks
Thank you True Logics Pro, we are glad you found this video helpful.
У меня проблема с датчиками, при расстоянии от 300 мм до 780мм и 840-2000мм всё хорошо, но при расстоянии 780-840мм начинает светиться датчик красным, и показания на экране сбрасывается на значение 31мм. Как настроить? Есть ощущение, что это как мертвая зона. И датчик считает что объект слишком близко. UC4000-30GM-IUR2-V15
Hello. How to make ultrasonic sensor synchronization connections for internal synchronisation for UB500? Do I just connect idividual synchronisation wires together?
Hello nixth3x, the following synchronization modes are possible:
1. Several sensors (max. number see technical data) can be synchronized together by interconnecting their respective synchronization inputs. In this case, each sensor alternately transmits ultrasonic pulses in a self multiplexing mode. No two sensors will transmit pulses at the same time (see note below).
2. Multiple sensors can be controlled by the same external synchronization signal. In this mode, the sensors are triggered in parallel and are synchronized by a common external synchronization pulse.
3. A separate synchronization pulse can be sent to each individual sensor. In this mode, the sensors operate in external multiplex mode (see note below).
4. A high level (+UB) on the synchronization input switches the sensor to standby mode.
Note: Sensor response times will increase proportionally to the number of sensors that are in the synchronization string. This is a result of the multiplexing of the ultrasonic transmit and receive signal and the resulting increase in the measurement cycle time.
We hope you've found this information useful. You can view this information on our datasheet for the UB500-18GM75-E5-V15 here www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=15010 or if you have further questions, please visit us here www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm.
Thank you.
Añadir a la Watch List

como puedo configurar este Sensor hagan videos porfavor Sensor ultrasónico UB5000-F42-UK-V95
Buenas tardes Eduardo, le comento que el sensor mencionado se configura meramente con los botones que tiene integrados. Con gusto comparto el documento PDF en Español que explica el procedimiento, éste es corto: files.pepperl-fuchs.com/webcat/navi/productInfo/pds/111686_spa.pdf?v=20220103160732 . De cualquier forma si tiene más dudas sugerimos escriba al mail jpayan@mx.pepperl-fuchs.com si necesita soporte técnico en Español. Saludos.
Hi there, need sensor that can detect plastic film like bin liners? Any ideas
Hello Kaatni, we're here to help. Our customer service agents and technical support specialists are ready to answer your questions and help you get the information you need.
Please fill out our Ask an Expert form by clicking this link here:
www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm
@PepperlFuchsUSA
Hi. Could you be kind enough to share how to change output mode from Normally Open to Normally Closed for uc6000-30gm70-2e2r2-v15.
Hi there Khawaja Naeem. You need to use the Ultrasonic sensor UC6000-30GM70-2E2R2-V15 www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=51811#software ULTRA-PROG-IR software in order to change those settings. The software can be found on the product page under the software tab. If you don't already have the cable, you will need it in order to interface the sensor with the computer you are using. The cable can be found at the bottom of the “Associated Products” tab. Interface cable UC-PROG-IR-USB www.pepperl-fuchs.com/usa/en/classid_190.htm?view=productdetails&prodid=69497.
We hope this helps!
@@PepperlFuchsUSA
Thanks for this kind support.
We have ub2000-f42-i-v15 sensor
We need 4-20A output with respect to distance 250mm to 1000mm
How to calibrate or teaching??
Hi there Venkatesh, you can program the sensor via the push-buttons on the unit itself. You may need to program the A1 (near) and A2 (far) points along with the rising ramp. You can find these steps on the datasheet that can be obtained in the link below, starting on page 4.
UB2000-F42-I-V15
www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=24959
@@PepperlFuchsUSA thank you very much 🙏
@@256venki you are welcome.
how to program ultrasonic sensor pepperl fuchs UC6000-30GM-IUR2-V15
Hi there Panwi AHPL, please review our datasheet for the UC6000-30GM-IUR2-V15 here: files.pepperl-fuchs.com/webcat/navi/productInfo/pds/104095_eng.pdf?v=20210524185045
Please review the "programming" section that begins on page 5, if you need further assistance please visit our website and fill out our Ask An Expert form www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm.
Thank you.
i have ub800-18gm(new), i follow your youtube intruction, but it's can't work.
the red LED on always..
can you help me?
Hello Irwan, We're here to help. Please fill out the Ask an Expert form so we can assist by clicking the link below.
www.pepperl-fuchs.com/usa/en/ask_an_expert_fa.htm
Thank you.
please share installation and operation of UB2000-F42-E6-V15 part no 133988
Hello Sama Vibes, the following link will provide the installation instructions for the UB2000-F42-E6-V15.
files.pepperl-fuchs.com/webcat/navi/productInfo/45/451492b.pdf?v=20200312072512
More information can be found on the product page of the UB2000-F42-E6-V15.”
www.pepperl-fuchs.com/usa/en/classid_186.htm?view=productdetails&prodid=24957
We hope this is helpful to you.