ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
How to make Single Push ON / OFF Circuit | Single Push Latching using IRFZ44N
ฝัง
- เผยแพร่เมื่อ 2 เม.ย. 2023
- How to make Single Push ON / OFF Circuit | Single Push Latching using IRFZ44N
Required Components:-
1) IRFZ44N Mosfet
2) BC558 Transistor
3) 10K Resistor x 2
4) 1M ohm, 100K ohm Resistor
5) 2.2uF Capacitor
6) Push Button
Circuit Diagram Link :- drive.google.com/file/d/1NEOY...
#electronicsproject #scienceproject #latching #irfz44n #bc558 #bc558 #transistor #mosfet
Thank you for Watching.....
Muy buen video.Yrabajas con elegancia.Horacio.Cali.Colombia.
Thank you so much....😊
Bom dia parabens muito bom excelente projeto
Thank you so much....
Great 👍 well done
Thank you 👍
Bom dia ,o meu q fiz aqui deu certo ,porém se vc for colocar um relé,igual eu fiz aqui ,eu recomendo q coloquem um resistor de 1 k nos pinos da bobina do relé ( 85..86) para não dar retorno no esquema , a força eletromotriz dá retorno alto para o bc 558 ,aí por isso q funciona só uma vez daí... Espero ter ajudado !!!
Thanks
I'm watching from Russia.
Well done! Simple and clear!
The author, is it possible to make a similar circuit for 220 V?
To get a pulse relay with one-button control?
~~~~~~~~~~~~~~~~~~~~
Смотрю из России.
Хорошо сделано!Просто и понятно!
Автор, а можно сделать подобную схему на 220 В?
Чтобы получилось импульсное реле с управлением от одной кнопки?
great, can I control the relay with a plus signal? Thank you
yeah its working, thanks
Most welcome.
How,i tried it many times it's not working
Interesante
Very good 😊
Thanks 😊
V good bro
Ta loko
Top
Thanks
Os que eu faço não funciona não, usei um Mosfet IRF510N no lugar do IRFZ44N, e o transistor BC557 no lugar do BC558, o resto segui como está no vídeo e fica sempre ligado. Interessante que site de simulação funciona
Try flipping the FET drain&source (pin2&3) and/OR transistor pins1&3 emitter & collector end pins
Is it possible to assemble this circuit with 9v and a diffused LED?
Olá amigo instalei o projeto pra acionar um relé no carro mas as veses ele aciona o relé sozinho quando abri a porta do carro vc pode me dar uma ajuda
Com esquema ficaria muito melhor...
How many volts and how many amps can this circuit handle?
Instead of LEDs, can you activate a 12v relay at the output?
incompleto falta o esquema eletrico
Hi! Can i put a 3amp load?
Would be possible make with 5 bottons and when press one of them, the others turn off?
😅😅😅 good work
Thanks
Hello, can you make a video or comment on how to change the circuit to a circuit that works on 5 volts and 3v lighting?
Hice el mismo circuito y el LED permanece encendido
apakah ini aman untuk pemakaian jangka panjang?
How much load and time can drive ?
its powering on the movement supply is connected. How to eliminate this
Tem como colocar um receive IR no lugar do push button?
Yes
@@anuragprojects bom dia amigo faz um vídeo ensinando como adaptar um receive IR no lugar do push Button?
can it operated at 3.7 volt
Im waiting for this answer...
Did you get an answer?
Bs 170
It's okay but give with schematic diagram
Circuit Diagram Link is given in the Description. Thanks for Watching my Videos.
But with it don't work over 12 v vcc
use 220v please
thunbs down -- why not show a circuit diagram??
Link is given in the discription. Thank you
Está na descrição
Спаял всё правильно, детали исправны, но не работает .
Simulated it but failed to work
It did not work
It doesn't work, don't bother in vain
Tried it to, bought and soldered it as drawing but failed
@@louislule4458 The circuit in the video works with 12v, but I tried it with 3.7v, it didn't work, do you have a project to work with an energy around 3v?
@@emin_musaogluUz cik lielu jaudu vajag to slēdzi?
@@emin_musaoglu use ic ne555 project