HOW TO CLEAN, LUBRICATE, AND ADJUST THE BLUESTREAK 629 FABRIC CUTTING MACHINE

[@DeanArwinTV]

Ang galing ng video nyo sir nakakatulong at may kaalaman.

[@VaLentinOGanadoreS]

thank po sir, keep watching

[@savannamarsan6995]

Thank u for sharing your ideas ..

[@VaLentinOGanadoreS]

Glad you like them!

[@ljcruzvlog9372]

So clean po idol galing po, merry christmas po

[@VaLentinOGanadoreS]

Thanks for watching po

[@sergio-ub6vx]

Como arreglar rira mucho la banda del lado derecho y como arreglar el filo de la navaja

[@VaLentinOGanadoreS]

The knife should be at center of the sharpening belt. Do it by turning sharpener centering adjusting screw. You tighten or loosen the belt by setting its pressure spring. Thank you for watching.

[@madels5729]

Thank you for sharing this info

[@VaLentinOGanadoreS]

You are so welcome

[@tinonggumawa4264]

So clear information, thanks for sharing this video.

[@VaLentinOGanadoreS]

Glad it was helpful!

[@nikkouayan9250]

sir I would like to ask why the knife is still moving even though the screw of the knife is tightened

[@VaLentinOGanadoreS]

Pls make sure that the lock washer is there with the set screw. Check also the thread of the set screw if it is still okay or need to change with new screw. Thank you sir.

[@teamestopare175]

What a skill po ang galing nyo namn po. Good job po

[@VaLentinOGanadoreS]

salamat po sa pag watch.

[@AmbrosialEntertainment]

Nice sharing keep growing ❤❤

[@VaLentinOGanadoreS]

Stay connected

[@Silbidorazvlogs]

Salamuch for sharing your video sir..

[@VaLentinOGanadoreS]

Thank you too

[@CAFETAMBAYANVLOGS]

Beautiful video Tutorial. Keep it up#tjms

[@VaLentinOGanadoreS]

Thanks a million

[@judyloneza9472]

thanks for sharing

[@VaLentinOGanadoreS]

Thanks for watching!

[@hoonjivlogs]

Thanks for sharing this ❤️

[@VaLentinOGanadoreS]

My pleasure 😊

[@ShijanSpike07]

what is that rotating parts name in the end of the video?

[@VaLentinOGanadoreS]

That is the driver pulley. It drives the sharpener to go up and down, thank you for watching sir.

[@softplayballpits8799]

Can you help moter jam
Suddenly motar jammed

[@VaLentinOGanadoreS]

check the capacitor for single phase motor, check motor shaft bearing for lubrication, check moving parts for alignment. thank you

[@lanceregeniovlogz5682]

Thanks for sharing this tutorial #tjms

[@VaLentinOGanadoreS]

Thanks for watching

[@Unicahija-y8f]

merry christmas po sir happy new yewr narin po

[@VaLentinOGanadoreS]

same to you po, thanks for watching

[@MaimaiLagat]

Galing mo nman maglinis po kuya,stay safe po#tjms

[@janetoray891]

Thanks for sharing sir nice content and god bless you from #tjmstv

[@VaLentinOGanadoreS]

Thanks for visiting

[@gemysabelle2683]

THANK you for sharing your knowledge kuya..keep it up..#tjms

[@VaLentinOGanadoreS]

Thank you too

[@leoceasarvlogs2275]

Thank you sir for another ideas your shared
#tjmstv

[@VaLentinOGanadoreS]

So nice of you

[@ZehamTVcastro]

thanks for sharing the video i learn something#tjmstv

[@VaLentinOGanadoreS]

Thanks for watching!

[@kambalniideasbysiro1114]

nice info. thanks for sharing sir. #TJMs

[@VaLentinOGanadoreS]

Thanks for visiting

[@gemysabelle2683]

Good health po lagi sau kuya..#tjms

[@SimplyAmazing-ud1ui]

Very interested and helpful. #tjms

[@VaLentinOGanadoreS]

Glad it was helpful!

[@aileen6974]

Gud day Sir, tanong ko lng po Paano po mgpalit ng liha sa cutting mchine? Salamat po

[@VaLentinOGanadoreS]

Yes maam, may video na po tayo dyan sa channel ntin, isearch nyo lng po ang pamagat niya ay, "how to change sharpening belts of bluestreak machine, salamat po maam,

[@indaydiona8994]

Ang galing manan po godbless po#tjms

[@hannahjuarevlog2909]

Thanks for the sharing to us sir keep more vlogging #TJMs

[@VaLentinOGanadoreS]

More to come!

[@nikkouayan9250]

what's the problem why it's getting easier

[@dennisiloco948]

Nice content sir,keep on sharing.#tjms

[@VaLentinOGanadoreS]

Thank you, I will

[@JeccyChanela28]

Slamt po sir for sharing keep safe always #tjmstv

[@VaLentinOGanadoreS]

Thanks, you too!

[@vlogniangkoljeff8356]

idol bakit kong cutting machine ko yong langis po nya ay na agos po jan sa my blade tapos mg lagay ng ako ng langis hindi na pupunta sa reserva

[@VaLentinOGanadoreS]

check nyo po ang oil felt baka sira. dapat pag lagay mo ng oil sa reservoir dadaloy unti unti sa felt papunta sa blade pag umaandar na ang machine. pagnakahinto hindi dapat umaagos sa blade. yunt felt ay parang basahan na dinadaanan ng oil papunta sa blade. ang langis dapat yung pang eastman cutting machine din ang gamitin mo. wag yung pang sewing machine kasi malabnaw yun.

[@donnachuzchannel2481]

Hello so very big harang congratulations po#tjms

[@VaLentinOGanadoreS]

Thanks so much

[@candice195]

Thank you po sa info #tjms

[@VaLentinOGanadoreS]

you are so welcome, thank you for watching.

[@MaimaiLagat]

Thank you po,God bless#tjms

[@VaLentinOGanadoreS]

Thank you too

[@docepimenta9474]

Hello, my friend i am from Brazil. You are contry?

[@VaLentinOGanadoreS]

Hello there, I am a Filipino. Thanks for watching

[@allaneugenio6734]

Pano po pag umuugong lang pero ayaw umandar

[@roelperu858]

Paano Kung bigla nalang po mawalan ng power

[@ramosliwanag9746]

kuya tanong q Lang po Pano po Kung ayaw bumalik iyong pang hasa, bumababa pero ayaw umakyat

[@VaLentinOGanadoreS]

Mga maaring problema, una baka baligtad ang rotation ng motor. Pangalawa, baka pudpud na ang gears na nagpapaikot ng square shaft. Pangatlo, baka yung rubber wheel ay di na kumakapit ng ayos sa balance wheel. Thanks po for viewing.

[@erinnoval4077]

Gud morning Lodi ask ko lang po kung paano Po I gagawin pag stock up ung blade ng cutting machine. Salamat po god bless

[@parengdaddyidol4887]

sir tanong lng po yong cutting machine may pag ginagamit may ground sya nbili ko lng second hand ano kya dahilan .

[@VaLentinOGanadoreS]

Malamang sir may leak ang windings nyan. Ibig ko sabihin may nasugatan na wires tapos dumikit sa body ng machine. Delikado Yan sir, I hat kayo. I check mo Yung wirings gamut ang tester Para Malamang mo Kung Alin may sugat. Lagyan mo ng tape. Siguruhin mo na nakakabit din ang ground wire. Ang ground wire ay kulay green or yellow green. Salamat po.

[@parengdaddyidol4887]

@@VaLentinOGanadoreS slmt po sir checko Uli.

[@roelperu858]

Paano po Yun bigla nawala ng power Yun Cutting machine po.
Anu po ang pinaka pangunahin dagilan po...

[@VaLentinOGanadoreS]

icheck nyo po ang male and female connection socket. minsan po kasi naluwag po yan pag matagal na ginagamit, check nyo rin ang power chord nyo kung may loose connection. salamat po

[@jiromelvale3026]

Ask Ko lang alam niyo po ba kung saan nakakabili ng mga parts nyan? tulad ng centrifugal switch

[@VaLentinOGanadoreS]

Yung po ganyan model ay walang centifugal switch, kung yung sa inyo cutting machine ay meron, available po sa lazada ang mga centifugal switch, sure nyo lng ma order nyo yung exactong kagaya ng sa inyo. Salamat po sir.

[@renanteescote629]

Hi po sir tanung kulang PO Sana ayaw po Kasi gumana ung blade Anu po Kaya problema sa cutting machine

[@renanteescote629]

Sana o sir mapansin nyo message ko salamat po

[@VaLentinOGanadoreS]

Opo sir remante, pano po bang ayaw? Di po gumagalaw o di po tumatalab sa tela? Umaandar po ba ang motor? Mapurol po ba ang blade? Paki linaw po sir, matulungan kita sa problem mo, salamat po

[@ronnierodriguez7893]

Pano nmn po pg mbilis uminit

[@VaLentinOGanadoreS]

Ang cause po ng paginit ng machine ay pag hirap sya sa pagikot. Makapal at matigas ba ang tinatabas o wala sa align yung slider ng connecting rod? Pede rin kulang sa lubrication kaya mabilis uminit ang machine. Yan sir ang possible factors.

[@EmelitaDeRosas]

Bkit po ng iinit cutting machie

[@VaLentinOGanadoreS]

Marami pong dahilan, isa po ay hindi smooth ang ikot nya. Dahilan po ay poor lubrication o misalignment ng mga parts.