I appreciate greatly this kind of video showing the dangers of such maneuver. I’m not criticizing at all, actually this shows that the whole operation must be carried with more precautions. Thank you so much for posting this 👍🏻. Most people only show how to do it but it’s important to also address the possible problems. Thanks again from Mexico! 🇲🇽
That blue tank is maybe large enough for a 15kw unit for a short time. You do not want the water boiling like that. With the water boiling like shown the plates can not stay 100% in contact with the water. The water is being blown away from the plates due to the boiling. Boiling allows air pockets Resulting in the fluctuating amperage. Salt is not necessary if the tank is large enough. I did 2 such load bank jobs in a fresh water river. Never remove the plates until the breaker is opened. The separation of the plates needs to be much greater - we separated our plates about 16”. Whoever was in charge should be fired - very dangerous setup.
I appreciate your review. But the salt here is used to Check the load on instant. The mistake here happened was. While we were not available our 1 engineer put salt on the Backalite. And that salt didn’t dissolved. You might hai seen dropping salt many times. That’s because we have changed water and added fresh water again. My motive here of uploading video was. In india this technique is used since 1990s. I want to teach our brothers that these kind of accidents can take place. Thank you 😊
That drum is way too small for the kind of power being dissipated. Way too much salt too. Boiling that hard will further concentrate the salt causing a runaway condition. Essentially that’s what happened when they pulled the electrodes out. Very salty water dripping off close spaced electrodes caused the arcing. Extremely dangerous. They need a tank of water about 10 times larger for a generator that size. And much bigger electrodes spaced at least 2-3 feet apart.
Actually the problem occur was due to our engineer put salt on the backalite. It should have been properly dissolved in the water. That salt did the spark
480VX421A=202kW If that water barrel holds 190L at 20C° that means it will reach 100C° in about 5 minutes or about 1 minute at full power. That water resistor is way undersized. Also do not take out the electrodes with power on! that's why such thing happened.
Yes we know. But the load banks are way too costlier to purchase and to maintain. So we have this alternative. Which is risky. But the footage you saw is rare of rare incidents happened.
Sir kya bliss ka jo engine ata tha kirloskar electric dg set me bo engine achha hei long lasting hoga plz help kijiye mujhe me kharidna chata hun ek admi se isiliye ouch raha hunn engine kesa hei alternotr kesa hei 62 kva ka dg set hei plz reply
I appreciate greatly this kind of video showing the dangers of such maneuver. I’m not criticizing at all, actually this shows that the whole operation must be carried with more precautions. Thank you so much for posting this 👍🏻. Most people only show how to do it but it’s important to also address the possible problems. Thanks again from Mexico! 🇲🇽
@@eduardosanchez7827 Thank you for understanding our motive to upload the video. 😊
That blue tank is maybe large enough for a 15kw unit for a short time.
You do not want the water boiling like that. With the water boiling like shown the plates can not stay 100% in contact with the water. The water is being blown away from the plates due to the boiling. Boiling allows air pockets Resulting in the fluctuating amperage.
Salt is not necessary if the tank is large enough. I did 2 such load bank jobs in a fresh water river.
Never remove the plates until the breaker is opened.
The separation of the plates needs to be much greater - we separated our plates about 16”.
Whoever was in charge should be fired - very dangerous setup.
I appreciate your review. But the salt here is used to Check the load on instant. The mistake here happened was. While we were not available our 1 engineer put salt on the Backalite. And that salt didn’t dissolved. You might hai seen dropping salt many times. That’s because we have changed water and added fresh water again. My motive here of uploading video was. In india this technique is used since 1990s. I want to teach our brothers that these kind of accidents can take place.
Thank you 😊
Is ok that plates are in line? I mean, should they be placed forming a triangle to guarantee a load balanced?
@@JPcostarica27 for a resistive load not needed
There is no risk of electrolysis products to be released creating a near explosive atmosphere?
That drum is way too small for the kind of power being dissipated. Way too much salt too.
Boiling that hard will further concentrate the salt causing a runaway condition. Essentially that’s what happened when they pulled the electrodes out. Very salty water dripping off close spaced electrodes caused the arcing. Extremely dangerous.
They need a tank of water about 10 times larger for a generator that size. And much bigger electrodes spaced at least 2-3 feet apart.
Actually the problem occur was due to our engineer put salt on the backalite. It should have been properly dissolved in the water. That salt did the spark
Hello bhai generator safe hai na
Haa ji bilkul safe ha
😂😂
Those guys are a walking accident.
Dude. Get a life. We are doing much better than you. Go and work.
@@surajdieselgenerator I agree with you
Look at urself before commenting
480VX421A=202kW If that water barrel holds 190L at 20C° that means it will reach 100C° in about 5 minutes or about 1 minute at full power. That water resistor is way undersized. Also do not take out the electrodes with power on! that's why such thing happened.
Basically the load varies.
But the calculations you gave is top notch.
We will consider it.
480v ou 400v ?
No safety
That is not a good way to do a load test
Yes we know. But the load banks are way too costlier to purchase and to maintain. So we have this alternative. Which is risky. But the footage you saw is rare of rare incidents happened.
@@surajdieselgenerator so do you guys plan to get the one which is safe
@@urboydexter Yes we are planning to make one instead of buying.
What happens when it arcs like that? Does the generator automatically switch off?
If the ACB breaker contains Earth Fault Relay.
The Breaker will shut down.
But Generator won’t stop you have to stop it.
Sir kya bliss ka jo engine ata tha kirloskar electric dg set me bo engine achha hei long lasting hoga plz help kijiye mujhe me kharidna chata hun ek admi se isiliye ouch raha hunn engine kesa hei alternotr kesa hei 62 kva ka dg set hei plz reply
Aap whatsapp kijiye photos. Ham bata denge uski condition
+919033353459
👍
Mccb trip huva ki nahi
MCCB nhi ACB aata hai.
Or trip hua.
Is this Cummins Genset?
Yes Cummins KTA3067 SERIES
Sir esa ku hogya.
Excessive Salt Use ho gaya. Salt dalne wale ne Salt ko paani me nhi milaya. Usse BAKALITE me blast ho gaya. Or Load Bank Pighal gaya
@@surajdieselgenerator sir i really appreciate your work and your response 👍👍
@@vikrammalviya7917 thank you 😊
😱
125 kv price ?
Adressss
too much salt
Yes excess 🧂
V16 turbocharged?
Yes. V16 Turbocharged
3067 Litres of displacement.
@@surajdieselgenerator ok thanks for the information