I've been doing this for years the same way only I used toothpaste as my polishing compound, it totally works! Try and keep the heads and blades sorted so they go back in the same head. Great video!
I like this inexpensive option a lot better. Also, I put the blades backwards and run the shaver against the mirror so as to polish without all the hard work.
Would like to see how you put blades backwards thats a magician trick. Can only run one way with blades against a surface and have yet to see a shaver that has a reverse
@@joescheller6680 good question, because there is no "backwards". The blades go in one way only. And if you remove the screen to expose the blades, they'll fall out. You can't run the shaver against the mirror, when using the diamond paste.
I had kept aside my Philips AquaTouch, after five years of usage, assuming that I cannot get new blades again, without spending a fortune. Philips was asking for nearly 70% of the cost of a new machine, for a set of three blades ! So I had got one of the Chinese machines (@ just 30% of the cost of Philips) and it was doing an ok job of my shaving. Today, after reading this article I carried out the polishing of the blades by re-grinding them as demonstrated in this video. What happened ? By Jove, I got three new blades for FREE !! Thanks for a great video.
I figured what do I have to lose. I was actually ISO new blades when I found some of these vids. I actually used an old cheap tablet screen and toothpaste and it actually worked. Thanks
@@roscored1000 Stones can only be used on the older blades which are flat. Newer blades are curved concave and would no longer fit the curved head if you grind them flat.
Thank you for this video. All those old Norelco blades that I have been saving over the years, have now been restored to a very sharp condition. A small piece of glass, very fine wet dry sand paper and some automobile rubbing compound did the trick. I wet the sand paper with some 30 weight oil and cleaned the blades in paint thinner and blew them dry with compressed air.
so i took the advise of these people in the comments and used a sandwhich plate that is flat and used toothpaste the blades cut better than when they were brand new. Thank you was not looking forward to replacing my blades again and now i won't have to oxidation sucks!! Shave on gents!! \m/
Glad you found this useful. I don't make many videos, but need a few more subscribers in order for TH-cam to reward me for my efforts, so if anyone can subscribe that will help me, many thanks
i just cleaned mine incredible i actually thught it was too hard now chagrin ,thank you for your help,i used to just buy another razor?Mine was so dirty the motor was struggling.
For best results take off the razer Head holding the blades. Take blades out of holder and put face down on a smooth porcelain plate with Abit of toothpaste watered down a little then place Razer on top of blades making sure there slotted and very lightly press and turn on and move gently in a circular action for 15 seconds only. Try first and repeat if needed
Just circling back. I had bought 2 grades of diamond paste - 5 micro and 2.5 micron. I went with the 5 (blue). I did not really see much of a color change to the paste. But it was more noticeable after doing 3 blade units. My mirror had a really nice patina of scratches so, it wasn't for lack of rotations. Mine weren't that dull to begin with, so I guess that's why. In any case, it seemed to work.
I put about 3/4 inch or 3 cm of vinegar in a flat bottomed bowl and then turned my razer on and dipped it in the vinegar and tapped it on the bottom of the bowl gently for about a minute. More hair came out after I did a really good cleaning and took everything apart.
Do not use this, as your Philips/Norelco has likely rounded (!) DOUBLE layer blades. You will just grind off the rounded edge and will also grind the two layers together. Your razor may be sharp for a few days, but then it will be worse. This is what I did, with 6+ years old blades, and it works great: 1. Put cutters and foil part in vinegar. (Oxidation is the main reason why the blades become dull, vinegar dissolves the oxidation and crud). Soak for 1-2 hrs 2. Take out, use toothbrush and brush the cutters well. Carefully brush the foil part also. Put back in vinegar again for an hour or so. Take out. 3. Rinse with water. 4. Now put the stuff in alcohol, another 30-60mins. May not be needed, but I do. Afterwards, take out, rinse. 5. As a final touch, reassemble razor, put toothpaste in your palm and then press the running razor against the toothpaste, press and move around in your hand a bit like you're shaving the inside of your hand. Have it run for about a minute. If razor gets slow because toothpaste dries, add some water. 6. Rinse This worked for me. I wouldn't use any abrasives
Have exactly the same razor as this guy, did exactly the same and the blades don't cut at all anymore, had to buy expensive new blades, so to the poster of the video; thanks for letting me loose money with your bullshit advice.
Thank you for the video-instructions. I was going to re-sharpen the blade but after I removed the blade from the housing, it turned out there's a lof of hair trapped in there. After removing it I can use it again. because the blade still feels sharp. I have remove the razor blade housing from the head before but did not try remove the the blade itself from the housing.
Diamond paste seems a little drastic so I'm thinking of using toothpaste instead. I've got a Philishave electric razor model SC 7759 from the 1950's and blades are hard to come by, don't want to take a chance on overdoing it.
Thank you for the very useful video. I do not believe I can find Diamond cutting paste in the country I live. Is there an alternative product that I can use or is there another process? Thank you for your feedback.
The blades are matched with the heads and should be honed together. Its like sharpening only one blade on a pair of scissors. I put a dab of polish in the palm of my hand and just work the head/cutter combination around in the polish with the razor running. It hones the blades and cutter at the same time.
Any automotive cutting compound will work, but to speed up the process start with 2000 grit wet and dry and finish with the compound. I use a large wall tile instead of a mirror. Be patient and dont overdo the wet and dry
Why is the sharpened /honed edge of the blade face in the opposite direction of rotation of the Norelco shavers? The Norelco shafts turn CCW, so the honed end of the blade is on the CW end of the hair as it is being cut?
I usually just cook them in water and sodium carbonate and give it a good stir to clean them. I use tap water but it would be better to use demineralized water I suppose. Still, they come out shining and they feel sharper as well.
If it works why change it. I use the vinegar as it removes the grease that holds the dirt hence the cleaning. Personally I would think tap water is fine
Just a few points: diamond paste-yes, tooth paste-not so good (reason: tooth paste abrasive is softer than blade), 2nd point - these razor blades have a radius, so a flat surface will flatten only the high point of the radius and technically, this will simply increase the gap between the blade and the shell (you'll be increasing the cutting clearance, which means the whiskers are inclined to bend rather than shear). You need a stereo microscope or similar to see the radius, which matches the shell. That said, I will try this method because I have little to lose as I've taken to shaving the bulk of my beard electric and then manual stick razor for smoothing.
Just use water for lube:During the war men sharpened razor blades with water in a jar rubbing the blade against the sides of the jar;no need for abrasives;in fact after using an abrasive you should hone the cutter on the mirror with just water to get a super sharp edge
Oh wow! I was thinking to do this kind of thing but when I dismantled the cutting heads they were absolutely jam packed full of black stuff...! Im expecting it to work almost like new after removing all that shit... Dead skin, etc.
I just done this with fine sand papper and now the blade are much more blunter than before, l thought it might be because l did them clockwise and doesnt the razor spin anti clockwise.
Thank you. I can't believe it but I do have the counterfeit version The unmistakable way for me to determine this is that there was no PHILIPS Logo on the orange replacement tool. My next call is to Amazon.
As Philips shavers are self sharpening, there is no need to "sharpen" the blades. I never do and have had my shaver for years. Works as when it was new!
It's a bit frustrating that you haven't indicated the grit level of the diamond paste. The blue color indicates it may be 5 or 7 microns. Also, listing an eBay auction doesn't make any sense, because after 3 months the link will no longer function.
Well, Roger Downs, be fair: he didn't mention Norelco; nor did he claim this would work for any triple-head razor. Perhaps you might help those of us who have a (some) Norelco razor(s) by doing a vid on resharpening those buggers? As others have mentioned, there are other tools that could be used, such as super-fine "sandpaper" or my preference, a diamond sharpening stone. Of course, each of these are only suitable for blades with cutting edges - curved or straight - parallel to the axis of rotation
For curved blades I think we can adapt this method and instead of using the mirror as a surface use the foil/ head which it sits in and then turn it. If I get some more requests I'll have a go at this. Please subscribe to channel so you don't miss it. Thanks
No sound on video and no, the speaker was not crossed off. I really would like to see and hear how to sharpen cutter heads since I recently replaced mine as recommended and don't get a smooth shave.
I tried clone blades. They worked okay, but not like the originals. The clone blades that I had did not cut as close and were not as comfortable for moving along the skin surface. If you must buy new blades buy only the originals. If you have a low cost razor and you cannot sharpen the blades and your razor is more than a few years old it may pay to replace the complete razor. The Lithium batteries inside of the razor may start failing after about 3 years. In some models Philips does not support changing the batteries. You would have to source equivalent batteries and replace them on your own. The cost may not be worth it. There also the age factor of the electronic circuit boards in the razor. I would try sharpening the blades as a first attempt. If you can get a year or two more out of your razor, it could be well worth it.
I have a norelco razor over 30 years old original battery holds charge good yet. Probably quit tomorrow but it's been a good friend for long time replacement blades were cheap up until about 10 years ago now half cost of new razor.
Thanks for the video! Do you by chance have another image of the "Re-Grinding Case" would look like? The eBay product link that was shared in the Description seems to have expired.
It is really a question of how flat, mirrors are very flat and hard also cheap. Stainless sheet will not be as flat also the diamond grit will bed itself into the sheet easier than it does into the glass of the mirror
I wouldn't recommend that. Best case it might work a little, but some of them (especially whitening ones) contains little particles that may ruin the blades.
Well, your wrong. Blade sharpening and dulling will eventually take it's toll on any cutting tool, be it lawn mower, saw or electric razor. Do you really think those little particles are safe on tooth enamel but not steel? It works great and have been doing it for years.
Thank you for the comment If you have curved blades you can sharpen them inside the original head see th-cam.com/video/SuFyPW4n6vg/w-d-xo.html for this. The objective when sharpening is just to hone the edge not to take off excessive material to change the shape
I have not found one, the battery gives up eventually which is usually new shaver time. I kept one going for 6 years but now the battery is not holding charge well so may be time to change, perhaps I'll have to do another clip on changing the battery!
I use a low cost mirror as you need something smooth and perfectly flat. Yes it does trash the mirror which is why the include them so you don’t ruin a good mirror
Curved head blades ground on flat surface? The manufacturers make them curved not flat now, so you need to buy new blades rather than home sharpening. This method creates gaps in the (curved) blade edge.
Why not just run the razor while rubbing paste gently into it? That would hone the mating surfaces together, which would be best I would have thought...
Getting the paste to stay put is an issue, however I have done something very similar to your suggestion on another video th-cam.com/video/SuFyPW4n6vg/w-d-xo.html
Did you tried it? According to those it should work th-cam.com/video/I3MZunTKY1Q/w-d-xo.html and www.philips.pl/c-p/RQ12_70/shaver-series-9000-sensotouch-element-golacy
It needs to be perfectly flat for best results, or if you look at another one of my videos it is possible to use the head as that is a mating surface if the blades are not flat. Plates are neither flat nor matched to the curve of the blade
Me and my cousin karl, you know the guy who has one eye that looks at you sideways, have to wait until around noon to get to shave on count of the water in the cattle trough is waaaaay warmer than at sunrise, so I'm gonna tell him about this and see what he thinks...
TOOTHPASTE is a minor abrasive; it's touted to be able to remove scratches from headlight lenses. I think I'll try that before I go out and buy diamond paste or polishing gel or polishing paste, heh?
will work just as well, I suggested veg oil as it is very light oil, works well and is in most households, same as the vinegar you could use degreaser instead, both work but vinegar is more common.
THIS DOES NOT WORK. There are TWO cutting surfaces both of which must be sharp and they must MATCH. Sharpening the NON ROTATING surface is virtually impossible. This will help a little but not much.
Your not supposed too do that, I have found out it's best to get New Blades the set . And your not supposed too mixup the set ! I keep mine clean and oiled when needed !! I had Good luck Too. Just read your paperwork from Norelco !!!!
I've been doing this for years the same way only I used toothpaste as my polishing compound, it totally works! Try and keep the heads and blades sorted so they go back in the same head. Great video!
I like this inexpensive option a lot better. Also, I put the blades backwards and run the shaver against the mirror so as to polish without all the hard work.
ya i use tooth paste too is there a video in here about it 2 & works better & easier
Would like to see how you put blades backwards thats a magician trick. Can only run one way with blades against a surface and have yet to see a shaver that has a reverse
@@joescheller6680 good question, because there is no "backwards". The blades go in one way only. And if you remove the screen to expose the blades, they'll fall out. You can't run the shaver against the mirror, when using the diamond paste.
Worked for my 10 year old shaver. . It was tearing my neck to pieces, now I am super smooth after shaving, so thanks.. I was about to throw mine out 😊
I had kept aside my Philips AquaTouch, after five years of usage, assuming that I cannot get new blades again, without spending a fortune. Philips was asking for nearly 70% of the cost of a new machine, for a set of three blades ! So I had got one of the Chinese machines (@ just 30% of the cost of Philips) and it was doing an ok job of my shaving. Today, after reading this article I carried out the polishing of the blades by re-grinding them as demonstrated in this video. What happened ? By Jove, I got three new blades for FREE !! Thanks for a great video.
Glad to be of service
I figured what do I have to lose. I was actually ISO new blades when I found some of these vids. I actually used an old cheap tablet screen and toothpaste and it actually worked. Thanks
I used a 1500 grit diamond stone that I have for knife sharpening. Works great.
Thanks for your post.
I am trialling a 3000 grit stone to see if it makes any difference
@@roscored1000 Stones can only be used on the older blades which are flat. Newer blades are curved concave and would no longer fit the curved head if you grind them flat.
@@baklash1762 so no different than using a mirror it's flat also.
@@joescheller6680 Yes Correct. My shaver and the blades are the old ones…just like me…and not as sharp as they use to be…just like me.
So simple! It discusses putting new blades into the empty circles. So Happy!
This is a great cost effective and money saving method to continue getting optimal performance from your shaver
DIY does it again! Thanks also to everyone who posted their methods as well.
Thank you for this video. All those old Norelco blades that I have been saving over the years, have now been restored to a very sharp condition. A small piece of glass, very fine wet dry sand paper and some automobile rubbing compound did the trick. I wet the sand paper with some 30 weight oil and cleaned the blades in paint thinner and blew them dry with compressed air.
so i took the advise of these people in the comments and used a sandwhich plate that is flat and used toothpaste the blades cut better than when they were brand new. Thank you was not looking forward to replacing my blades again and now i won't have to oxidation sucks!! Shave on gents!! \m/
Glad to be of help, Personally I think toothpaste less precise and not as effective as a grinding paste, but happy that it has worked for you
Followed the instructions to the letter and what a difference, thank you
Glad you found this useful. I don't make many videos, but need a few more subscribers in order for TH-cam to reward me for my efforts, so if anyone can subscribe that will help me, many thanks
i just cleaned mine incredible i actually thught it was too hard now chagrin ,thank you for your help,i used to just buy another razor?Mine was so dirty the motor was struggling.
My blade is 8 years old, still in good shape. Did nothing other than just cleaning under the warm water. Philips make things.
I have been using a whetstone 6000 grit. It's white actually observe the gray metal leaving the blades. It's amazing
For best results take off the razer Head holding the blades. Take blades out of holder and put face down on a smooth porcelain plate with Abit of toothpaste watered down a little then place Razer on top of blades making sure there slotted and very lightly press and turn on and move gently in a circular action for 15 seconds only. Try first and repeat if needed
Just circling back. I had bought 2 grades of diamond paste - 5 micro and 2.5 micron. I went with the 5 (blue). I did not really see much of a color change to the paste. But it was more noticeable after doing 3 blade units. My mirror had a really nice patina of scratches so, it wasn't for lack of rotations. Mine weren't that dull to begin with, so I guess that's why. In any case, it seemed to work.
I'll need to use this method with my grandfathers Speedshaver norelco, one of the 60's one.
ready to throw mine out ,saw this and now it is working great
absolutely brilliant....i used t-cut car polish hahaha.....my shavers like brand new!!!!! great video & saved a few quid!!!
Good idea , I thought of a grid stone but could not find. I ended up with silvo.
See what happens.
My Mrs is going kill me when she sees her mirror 😂. Ruined ... can you do a video on how to restore ground up mirrors?
Clear and to the point.
I put about 3/4 inch or 3 cm of vinegar in a flat bottomed bowl and then turned my razer on and dipped it in the vinegar and tapped it on the bottom of the bowl gently for about a minute. More hair came out after I did a really good cleaning and took everything apart.
Do not use this, as your Philips/Norelco has likely rounded (!) DOUBLE layer blades. You will just grind off the rounded edge and will also grind the two layers together. Your razor may be sharp for a few days, but then it will be worse. This is what I did, with 6+ years old blades, and it works great:
1. Put cutters and foil part in vinegar. (Oxidation is the main reason why the blades become dull, vinegar dissolves the oxidation and crud). Soak for 1-2 hrs
2. Take out, use toothbrush and brush the cutters well. Carefully brush the foil part also. Put back in vinegar again for an hour or so. Take out.
3. Rinse with water.
4. Now put the stuff in alcohol, another 30-60mins. May not be needed, but I do. Afterwards, take out, rinse.
5. As a final touch, reassemble razor, put toothpaste in your palm and then press the running razor against the toothpaste, press and move around in your hand a bit like you're shaving the inside of your hand. Have it run for about a minute. If razor gets slow because toothpaste dries, add some water.
6. Rinse
This worked for me. I wouldn't use any abrasives
Absolutely true, about curved blades. Also, eventually you grind away from the rounded slots.
Toothpaste is an abrassive, but a milder one
Have exactly the same razor as this guy, did exactly the same and the blades don't cut at all anymore, had to buy expensive new blades, so to the poster of the video; thanks for letting me loose money with your bullshit advice.
@@hermansnoeckx - If your money is loose, you need to tighten it.
What is the "foil part"?
I suppose a piece of window glass would do just as good as a mirror. A good video, Thank you.
Great idea!, but will ruin the glass, hence I use disposable mirror
Thank you for the video-instructions. I was going to re-sharpen the blade but after I removed the blade from the housing, it turned out there's a lof of hair trapped in there. After removing it I can use it again. because the blade still feels sharp. I have remove the razor blade housing from the head before but did not try remove the the blade itself from the housing.
good video thanks ,very well explained step by step
Thanks for sharing your video it worked great I sharpen my blades today thanks again
Glad it helped
Can you please name the blue material you used?
@@user-yi7bu9jf1o it's called Flitz metal polish. I bought it on Amazon
Diamond paste seems a little drastic so I'm thinking of using toothpaste instead. I've got a Philishave electric razor model SC 7759 from the 1950's and blades are hard to come by, don't want to take a chance on overdoing it.
I took out the blade and soaked them into coffee maker descaling solution. Its acidic so hopefully it cleans the oxidation off
Thank you for the very useful video. I do not believe I can find Diamond cutting paste in the country I live. Is there an alternative product that I can use or is there another process? Thank you for your feedback.
The blades are matched with the heads and should be honed together. Its like sharpening only one blade on a pair of scissors. I put a dab of polish in the palm of my hand and just work the head/cutter combination around in the polish with the razor running. It hones the blades and cutter at the same time.
Any automotive cutting compound will work, but to speed up the process start with 2000 grit wet and dry and finish with the compound. I use a large wall tile instead of a mirror. Be patient and dont overdo the wet and dry
Why is the sharpened /honed edge of the blade face in the opposite direction of rotation of the Norelco shavers? The Norelco shafts turn CCW, so the honed end of the blade is on the CW end of the hair as it is being cut?
I usually just cook them in water and sodium carbonate and give it a good stir to clean them. I use tap water but it would be better to use demineralized water I suppose. Still, they come out shining and they feel sharper as well.
If it works why change it. I use the vinegar as it removes the grease that holds the dirt hence the cleaning. Personally I would think tap water is fine
Just a few points: diamond paste-yes, tooth paste-not so good (reason: tooth paste abrasive is softer than blade), 2nd point - these razor blades have a radius, so a flat surface will flatten only the high point of the radius and technically, this will simply increase the gap between the blade and the shell (you'll be increasing the cutting clearance, which means the whiskers are inclined to bend rather than shear). You need a stereo microscope or similar to see the radius, which matches the shell. That said, I will try this method because I have little to lose as I've taken to shaving the bulk of my beard electric and then manual stick razor for smoothing.
Similar to your points have a look at this method th-cam.com/video/SuFyPW4n6vg/w-d-xo.html
You can use the bottom of a ceramic coffee cup
Just use water for lube:During the war men sharpened razor blades with water in a jar rubbing the blade against the sides of the jar;no need for abrasives;in fact after using an abrasive you should hone the cutter on the mirror with just water to get a super sharp edge
Why is the mirror trashed? Can't it be reused for a future grinding?
Oh wow! I was thinking to do this kind of thing but when I dismantled the cutting heads they were absolutely jam packed full of black stuff...!
Im expecting it to work almost like new after removing all that shit... Dead skin, etc.
I just done this with fine sand papper and now the blade are much more blunter than before, l thought it might be because l did them clockwise and doesnt the razor spin anti clockwise.
I use 2000 grit wet sand paper
I should do this with one of my razors
Thank you. I can't believe it but I do have the counterfeit version The unmistakable way for me to determine this is that there was no PHILIPS Logo on the orange replacement tool. My next call is to Amazon.
Philips genuine blades have more cutters
Do you change the paste for each head or do all 3 with one mix?
I changed the paste each time. It does not use much so even a small tube is enough for this, probably twice over
As Philips shavers are self sharpening, there is no need to "sharpen" the blades. I never do and have had my shaver for years. Works as when it was new!
dollar stores have mirrors and who can beat that price for a sharpening tool
It's a bit frustrating that you haven't indicated the grit level of the diamond paste. The blue color indicates it may be 5 or 7 microns. Also, listing an eBay auction doesn't make any sense, because after 3 months the link will no longer function.
thanks fro the vid and tips. What grit is required for the Diamond polish paste? I see on ebay there are many different grit grades....
I have one circuit that makes a lot of noise when it rubs against the blade inside, and I haven't found a solution for it
My like boosted you to 1k likes. We need more videos like these. Do you like rotary better? What's the best way to make them last?
Many thanks. Keeping them clean I think is key to long life
He likes to say, "a little bit" a lot...lol. :-)
If you can do this, I bet you can disable printer's chip detecting ink level. When I refill the cartridge, the printer still displays empty.
When was the last time you saw a Norelco cutter with flat blades? MIne have had curved blades for years, and you can't hone them.
Well, Roger Downs, be fair: he didn't mention Norelco; nor did he claim this would work for any triple-head razor. Perhaps you might help those of us who have a (some) Norelco razor(s) by doing a vid on resharpening those buggers?
As others have mentioned, there are other tools that could be used, such as super-fine "sandpaper" or my preference, a diamond sharpening stone. Of course, each of these are only suitable for blades with cutting edges - curved or straight - parallel to the axis of rotation
For curved blades I think we can adapt this method and instead of using the mirror as a surface use the foil/ head which it sits in and then turn it. If I get some more requests I'll have a go at this. Please subscribe to channel so you don't miss it. Thanks
Thank you for the comment, try this method th-cam.com/video/SuFyPW4n6vg/w-d-xo.html works better for the shavers with curved blades.
No sound on video and no, the speaker was not crossed off. I really would like to see and hear how to sharpen cutter heads
since I recently replaced mine as recommended and don't get a smooth shave.
the sound cuts in after the intro titles approx 8 seconds in
Norelco suggests water only!
Ok video. But I don't know if it is recommended to clean the blades in hot water.Kitchen knives are rendered useless by hot water.
Hi, great video, do you recommend a specific grit of diamond paste? Some others have said use a metal polish. What do you think? Thanks, Mike
Yes I was wondering about Autosol metal polish?
I tried clone blades. They worked okay, but not like the originals. The clone blades that I had did not cut as close and were not as comfortable for moving along the skin surface. If you must buy new blades buy only the originals. If you have a low cost razor and you cannot sharpen the blades and your razor is more than a few years old it may pay to replace the complete razor.
The Lithium batteries inside of the razor may start failing after about 3 years. In some models Philips does not support changing the batteries. You would have to source equivalent batteries and replace them on your own. The cost may not be worth it. There also the age factor of the electronic circuit boards in the razor.
I would try sharpening the blades as a first attempt. If you can get a year or two more out of your razor, it could be well worth it.
Good comments and largely mirror my own views, the price of replacement blades are too high
Planned obsolescence it seems to require new razors every couple of years
I have a norelco razor over 30 years old original battery holds charge good yet. Probably quit tomorrow but it's been a good friend for long time replacement blades were cheap up until about 10 years ago now half cost of new razor.
Thankyou for that that is so kind of u
lol mine are about 5-6 years old. I think I need new ones asap
As good as new, or not quite as good as a brand new replacement head?
faNTASTIC .
Thank you! Cheers!
How to Shaver blade sharpening panasonic er2031k
Thanks for the video! Do you by chance have another image of the "Re-Grinding Case" would look like? The eBay product link that was shared in the Description seems to have expired.
I have updated the link now www.ebay.co.uk/itm/233322172615
, This will be valid for the next 3 sales, then will change again
No se como poner la goma azul
oh - and why use a mirror and not a stainless steel sheet for example ? anything flat and level is ok right?
It is really a question of how flat, mirrors are very flat and hard also cheap. Stainless sheet will not be as flat also the diamond grit will bed itself into the sheet easier than it does into the glass of the mirror
Can i use toothpaste instead of polishing paste?
Not tried it, don't think the abrasive is as consistent hence the reason my kits use 2000 grit diamond paste
What about using a nice smooth oilstone ?? (Get them from your local ironmongers / engineering supplies place).
Not something I have considered as they are nor perfectly flat, any wear makes them less flat, but you can give it a go
Jayen4 c
Tooth paste works.
I wouldn't recommend that. Best case it might work a little, but some of them (especially whitening ones) contains little particles that may ruin the blades.
Well, your wrong. Blade sharpening and dulling will eventually take it's toll on any cutting tool, be it lawn mower, saw or electric razor. Do you really think those little particles are safe on tooth enamel but not steel? It works great and have been doing it for years.
So do you ALSO use the fine grit sandpaper I've seen several people use? Thanks!
Tooth paste is the only cutter I use. Its brilliant.
Where do you get the paste? Do You need vegitibal oil ? or will water or mineraloil work to?
The link in comments goes to ebay where I sell the paste and mirror as a convient kit. any oil wil work, water does not
The paste is oil based so water does not wii oh ok but any oil will
What is that paste? Where can i buy? Does wicks sells? Halford? B&q?
Search eBay.co.uk for Rotary electric Shaver head resharpening kit to renew cutters / blade sharpening paste and mirror sold as a kit
Did you not ding the blades by shaking it?
not found that to be an issue. Other suggestions on the thread have suggested using plastic containers which would take away that risk completly
Would it be easier to use a fine grit wet sandpaper on a table?
a table is not flat enough, some use 2000 wet and dry as a first step.
....TRY a Belt Sander ....200 geit!! Amazing Results.....
What's that blue paste please help me with the name or where I can find it
If you click the link in the description, it links to the paste and mirror on ebay
This only works for a few days then it stars working like before.
How many times can you sharpen a blade. I've done mine 10 times.
You are way ahead of me. I've only reshaprened them 2-3 times
That's great! What method and products do you use? What grit #? Thanks!
Can you use tooth past too?
Not as good as an abrasive and irregualr sized grains
The blade tips are slightly curved, so I'm not sure this can work. You will be removing the curve and turning it flat.
Thank you for the comment
If you have curved blades you can sharpen them inside the original head see th-cam.com/video/SuFyPW4n6vg/w-d-xo.html for this.
The objective when sharpening is just to hone the edge not to take off excessive material to change the shape
Is there a limit to how many times you can sharpen blades?
I have not found one, the battery gives up eventually which is usually new shaver time. I kept one going for 6 years but now the battery is not holding charge well so may be time to change, perhaps I'll have to do another clip on changing the battery!
just get a very fine stone for sharpening. You get the same result.
1500 grit??
I liked this video...but why a mirror? ( thats a great way to ruin a mirror) .
I use a low cost mirror as you need something smooth and perfectly flat. Yes it does trash the mirror which is why the include them so you don’t ruin a good mirror
Curved head blades ground on flat surface? The manufacturers make them curved not flat now, so you need to buy new blades rather than home sharpening. This method creates gaps in the (curved) blade edge.
Why not just run the razor while rubbing paste gently into it? That would hone the mating surfaces together, which would be best I would have thought...
Getting the paste to stay put is an issue, however I have done something very similar to your suggestion on another video th-cam.com/video/SuFyPW4n6vg/w-d-xo.html
Hi, how often would you need to regrind the razors?
Initially after 2 years, after that I have once a year works for me
dodeedo1000 okay thanks
Hi! Can u help me?
I have a question: I have a philips rq1260 shaver, and I'd like to know if it works fine with the new blades head sh90. Thank!
Did you tried it? According to those it should work
th-cam.com/video/I3MZunTKY1Q/w-d-xo.html and www.philips.pl/c-p/RQ12_70/shaver-series-9000-sensotouch-element-golacy
Will a ceramic or glass dinner plate work as well as a mirror?
It needs to be perfectly flat for best results, or if you look at another one of my videos it is possible to use the head as that is a mating surface if the blades are not flat. Plates are neither flat nor matched to the curve of the blade
diamond cutting leaves microscopic particles of diamond in the metal(poisons it). carborundum does not do that.
Me and my cousin karl, you know the guy who has one eye that looks at you sideways, have to wait until around noon to get to shave on count of the water in the cattle trough is waaaaay warmer than at sunrise, so I'm gonna tell him about this and see what he thinks...
TOOTHPASTE is a minor abrasive; it's touted to be able to remove scratches from headlight lenses. I think I'll try that before I go out and buy diamond paste or polishing gel or polishing paste, heh?
or autosol polish for cars. same stuff you can use for blades.
What is name of tubeplease tell me
Yeah, I'll run down to the 7-Eleven and get some Diamond paste🤔
try www.banggood.com/8pcs-5g-Diamond-Polishing-Paste-Lapping-Compound-Mold-Polishing-Tool-set-0_5-10_0-Micron-p-1048652.html?rmmds=myorder&cur_warehouse=CN
Kit now back in stock see www.ebay.co.uk/itm/232895483834
I watched to see how to put together. You skipped that part
weeeellll, not sure if its worth the time. any business out there willing to offer this sharpening service??? that would be game changing
nogardsiete Takes like 10 min to do it. And saves you like $35 in buying new blades. What are you smoking?💯🤣
Don't use veg oil, just use small amount of mineral oil like you use for sharpening blades.
will work just as well, I suggested veg oil as it is very light oil, works well and is in most households, same as the vinegar you could use degreaser instead, both work but vinegar is more common.
@@dodeedo which degreaser?
THIS DOES NOT WORK.
There are TWO cutting surfaces both of which must be sharp and they must MATCH.
Sharpening the NON ROTATING surface is virtually impossible.
This will help a little but not much.
No work ..
Worked for me
Did not work for me ?? . and say yes ... "Good By " to your nice mirror.
Yes it will ruin the mirror, that is why when I sell the kit I include as mirror as well as the diamond paste
This messed my blades right up. Don't do it!!
Your not supposed too do that, I have found out it's best to get New Blades the set .
And your not supposed too mixup the set !
I keep mine clean and oiled when needed !!
I had Good luck Too.
Just read your paperwork from Norelco !!!!
Another option is to buy a FOIL!!
Moral of this story: just buy a new damn set of blade heads. (Sorry mate. Your video was very informative though)...
Replacement razor heads aren't that expensive when you contrast the cost with manual razor blades. Useless video. Save time and buy new razor heads.
Yeah, and why not just use some beach sand or something...