The plate needs to be flat, the way you have it set up it disperses the energy due to the arc in the antenna. The energy is coming straight on. Point it to the East, because we travel through the aether and the spin of the Earth causes us to spin eastward. The higher you get it the more you will gather from the impedance difference. A minor amperage 2-3V A.C. added to the metal plate causes the antenna to gather energy from 10x the area of the physical antenna. The ground must be the same size as the antenna and buried 12-18" under the ground with a Good insulated wire to one leg of the capacitor. Wet the earth around the ground if the earth is dry. Give us a video after these modifications. Blessings!
If everything is tuned properly, and in balance, and your grounding rod is deep and the antenna is high enough, everything made in high quality, with a large array of tank circuits, you should see a worthwhile amount of energy accumulating nonstop.
@@ChrisChris-sj7zm: The video is misleading, because it seems to indicate that incident rays are what's powering it, even though she even remarks that it keeps functioning at night. In reality what's actually happening is that you're essentially "harvesting" atmospheric ions, which are arranged in an atmospheric electric field with a gradient of ~100 V/m near the ground, but much higher further up. To increase the energy harvested in this way what you want to do is to have the antenna as high up in the air as possible, and to have as much surface area on it as possible (a flat rectangle as shown here is a rather lousy design, better to make a fractal antenna or just use a dense copper mesh arranged in a spherical or cylindrical shape). During times of more atmospheric activity both in terms of wind and electrical activity (as during thunderstorms, but also during moist weather in general, the equatorial tropics would probably be a great place for something like this) there will be a lot more energy available. You essentially have to think about it in terms of how much charge you can collect on the antenna, which primarily comes from charged particles in the air rather than radiation; thus why more wind (more particles moving across it) and moister weather (more charge being conducted between the particles themselves) is better. If you do this you should also make sure to either use high-voltage capacitors or to regularly discharge the capacitors once they reach a certain voltage, because the voltage very high up will be quite large (as mentioned above, the field is ~100 V/m on a fair day near the ground, under a thunderstorm high up the field can easily reach 1000 V/m or more, for a total potential of tens of thousands of volts depending on how high up your collecting antenna is). These days you can get high-energy supercapacitors very cheaply, would probably be a perfect fit for this kind of thing, but they are rated for a low voltage in comparison, so you'd really have to make sure to monitor and discharge it (luckily they'd take a fair amount of time to reach their rated voltage, relatively speaking, so that shouldn't be too difficult).
Please, add a signal diode (like 1N60, BAT41, etc) between the antenna and the capacitor with the anode on the antenna side. Alternativelly you can put the diode between the antenna and ground, in parallel with the capacitor, with the cattode connected to the antenna side. I bet you will get much more charge in the same period of time.
Not one diode. Use 4 to make a full-wave bridge rectifier. If they are germanium, you have the "Joe Tate Ambient Power Module" circuit. You can use 6 diodes or even more.
How does adding a diode in parallel reverse the flow of current? I’m intrigued. Could two circuits be made, one series, one parallel and be connected in a way?
@jondelaire sorry my friend, dont be intrigued any more, you are right. I wrote my comment long time ago and I dont remember why I said that. Diode in parallel will not work. Just in serie or using a full-wave bridge as suggested by Chuck. I remember doing it when I was a kid, 40 years ago. Only difference is that I used a tank circuit tuned to AM broadcast band. Accumulated energy was used to power an AM receiver that worked with a couple of transistors and headsets and using the same tank circuit. It was basically a small radio that worked without batteries, published in the well known "Lúpin" magazine in Argentina. Regards! Adrián
You don't actually need the aluminum foil. Just having a wire up high in the air harvests IONs and generates the same charge. Another Nikola Tesla invention, one of many many innovations
There is so much wrong with the experiment. Tesla said heavily insulate the plate, use high tension/high voltage capacitors, and to have everything insulated for high voltage. You are also supposed to charge the plate negative. People replicate tesla's patents and completely leave out very important details.
Yea of course it works.. you really gonna put a plate high in the sky to get any usable energy from it? Where does tesla state to do that? This patent is only a clue, a partial circuit, a TUNED "reciever".. dont focus so much on the diagram details.. its not about pulling dc current from ground to sky..
Great to see a video about this topic that is not biassed in either direction. As a sidenote, the electrolytic capacitor may have accumulated some charge just from being heated by the sun to a higher temperature than what it was before.
The directions in his plans also say to insulate the metal plate. yours looks to be taped or glued to a pc of cardboard or something with your wire only tapped to the aluminum foil. Maybe a larger flat pc of steel or aluminum that is painted on all sides with rubber to insulate it, and the wire soldered to the plate? Higher is better.
All energy is free - it's the cost of, storing it, getting it to the end user, in a usable form, useful to that particular piece of equipment that costs.
When computer first came out, it was pricy and took up a lot of space. And what do we have now? What you think is costly can change in no time. Open your mind.
What is cost other then a made up currency system , all that’ stuff is free humans just decided god forbid anybody moves a finger for the greater good if they can’t profit from it , the irony is we would all profit of off working together and ending currency
As of now most energy comes from fossil fuels which arent free... it cost money to get people to do the work to mine the coal which is then burnt for energy.
Take a large inductance transformer coil with 300mh and 30mh. Get a second one just like it. Now hook a piezo element across the the ground and a high antenna wire. Connect one 300mh coil across the piezo. You may connected piezos in series to get higher voltage. Then connect the 30mh coil to each other. Then measure the output across the free 300mh coil for free energy.
he was a genius. at the time he is invented this technology, there was nor radio energy waves. if you do this today, you can get arrested, because you steal energy from the radio station and create a hole in the radiowave net. and they know where the hole is. they can track you down.
With the ions flowing thru, some charges on the caps remain. BUT, a better idea is to have the antenna to ground circuit oscillate and thus help in pumping more and more ions from the antenna and ground. If the antenna and ground plate are brought to a much higher voltage (> 100 volts), there can be slight ionization on the metal improving its ability to interface with the ions present nearby. The oscillation, or AC currents, can be converted to DC via germanium diodes (rate for high voltage), bridge rectifier, and charge a super-cap with the DC side.
I have experimented with this using an oscillator source, and the capacitors I worked with basically became "self charging" in the manner you speak of. I had a large cap, 50,000 mfd at 60v and it would self charge to around 3 volts ⚡️ Nice spark with 50,000 mfd 🤪
@@RGRundeRGRound Serious question, link to instructions please, I want to do this as well. It will be a fun side project to my electrostatic generator.
6:40 some suggestions for improvement. Wires are too long and too much resistance. Need short wires with high gauge, low resistance. Need a much better connection to ground. There should be a large iron plate buried deep underground. You want the ions from the ground to take the path you create to the sky (like the Great Pyramid of Gizah). Then, have a super cap and a boost converter to boost the low voltage to the target voltage. Consider also the Tate ambient power module circuit which uses germanium diodes. That circuit really works!!!
Certainly one shouldn't use wires longer then nessesary, and it is lower gauge wires that are thicker with lower resistance. But here, resistance in the wire here is not the issue for its poor performance, and trying to optimize the wire thickness for lower resistance to capture more power is a case study in diminishing returns. For example, if you have two setups in identical conditions. But one setup having a copper wire 10× cross section area than the other setup's copper wire of the same length, meaning the wire will cost maybe 10× more because it uses 10× copper, but is still unlikely to increase the power collected over a year by .0001% Yes a boost converter can convert low voltage to a higher voltage but boost converters use an oscillator circuit to pulse width modulate a signal to the switch just after the inductor in the boost converter. That oscillator will use up more power than the setup in the video collected, and fail to boost anything. One does not need iron buried deep underground. A typical grounding rod should be sufficient unless one lives in a desert. One can also use their water pipes as a good earth ground. The real limiting factor is that power available is a function of surface area and height of the collector. increasing both will do far more than spending additional money to optimise a lower resistance in the collector cable or improve the ground. Even then, it's not worth to spend $100 to get maybe $0.01 worth of electricity over a year. free energy here is little more than a lab curiosity. not a viable means to usefull energy.
@@domestinger8805 Yes the original commentor in this discussion thread was talking about collecting energy from moving electrons in the ground to the sky. The original commentor was suggesting improvements via lowering resistance from earth to sky. My comment was essentually indirectly saying that using the copper wires wasn't the source of most of the resistance in the circuit, that the negligible modest against from a thicker wire would be costly without a significant gain in performance, and most any existing earth ground will have sufficiently low resistance. I'm saying now that most of the resistance in the circuit comes from ion flow to the current collector surface area in the air. Yes a thicker wire has a greater surface area but that increases by the square while the cost of copper increases by the cubic volume for a given length, where as a longer thinner wire has a much greater surface area and reasomably low enough resistance for modest currents.
Great Video clip! Excuse me for the intrusion, I am interested in your initial thoughts. Have you ever tried - Malmenjaay Unexposed Inspiration (probably on Google)? It is a good exclusive product for discovering your mayan day sign and the clues it has to your future without the headache. Ive heard some amazing things about it and my work colleague finally got cool success with it.
Okay friends thanks for all the comments here's some little tidbits hints and clues that you can use for taking energy out of the air one you have to understand what the Zamboni pile is once you do you can start to understand free energy Robert Murray Smith channels talks about this if you can find his video. He also says that you can get one kilowatt a voltage out of this device but very little amps. Now here's the secret like a swing this is what the word scalar waves come from understand the word itself it is a scale so we start with the example a swing and at the seat sits a person who toggles her body back and forth with her legs in back this is the little energy that we were talkin about milliwatts if you understand the example, as you tap the peak of the energy you begin to make the energy increase little by little into you get this awesome wave that shouldn't happen but does. If you want to do research on that at Rogue wave, once you hear the scientific evidence on how these waves occur you see that Tesla scalar wave is not only possible have been used in many other scientific experiments. Now let's tell you this my name is Lloyd G stove on I work for Media Library oh, I'm also the person who defined overunity. Now many people disagree would I have been saying for over 31 years about overunity and tries to put in these fake terms so these are the things you must get around to understand the science that's being hidden right before your eyes. Let's do some common sense thinking overunity is a compound word over plus Unity; so how in the world does those two words ever mean perpetual motion they're lying to you they don't relate at all so when you hear my explanation on overunity read my published papers on the history of overunity you'll see that they most definitely don't want you to know anyting about overunity or scalar waves for that matter. Why because they explain away to take milliwatts and scale them into impossible amperage that should be impossible. That's why I mention rogue waves yes and the swing it only takes a small amount of energy 2 tap or spank that larger amount of energy 2 keep that energy going or increase it this is a science that most people haven't look into or study yet they use these methods all the time like keeping a spinning ball spinning on your finger for long periods of time. Swinging from almost Ground Zero without any assistance. Again there are secrets right before your eyes if you are looking but as long as you are buying into perpetual motion controversy and letting people tell you that overunity has something to do with perpetual motion the secret will be lost anyone who takes the time to read these Passage. I'm just a librarian who been working and using this type of energy for years we give out a number almost every time 313-651-5349. If you are shy and you don't want to talk just dropped a text message at 313-777-3031, and you should get a reply free energy is out there and has been used throughout history for millions of years the people who tell you otherwise are helping to keep this a secret, the car company Tesla didn't listen to those type of people and look where he is today remember or just go back and look at the evidence for yourself they told Tesla car company would he was trying to do was impossible and yet he did it you have to break through all these controversies and understand that Nikola Tesla's work is being used every day while at the same time they say he was a pseudoscientist, thank you if you read mine higher rhetoric
I also got 0.2V at 15ft. My antenna was homemade stainless steel sea urchin type. I used the joule thief circuit to harvest the accumulated charge. Happy experimenting!
@@obviouslytwo4u: When harvesting ions from the air as in these experiments, what you're getting is direct current, not alternating current, so there is no frequency.
Tesla's Wardencliffe tower was designed to receive energy wirelessly but through a different receiving method. However, the tower was 190 feet tall to reach a minimal point above the earth to be at a sufficient distance where the atmosphere as it's own capacitance, between upper atmospheric charge and the ground, are well enough separated that a sufficient usable voltage can naturally occur, and therefore, better harvested using the antenna and ground connection at such a height. Interestingly, the modern day replication of Tesla's work by a company in Texas USA named Texzon, also has towers this same height. Although both Tesla's and Texzon technology both use surface wave propagation, the atmosphere at this height separates the charge.
You really think so? I read that large gasoline or diesel motors were part of Wardencliffe. Hard to prove it after that cuck Morgan destroyed both it and Tesla.
Thank you for taking the time to do this experiment, show it, and explain it. I hope you keep doing this. Knowledge is important. Doing is important. One without the other is a plant without sunlight. Blessings, health, and safety to all....
Radiant energy (free energy) is not all energy from sunlight! The term "free energy" has been used by ether technology development engineers for many years, but it is not a pure concept. It is the energy extracted from Ether. The Magnifying Transmitter is a cutting edge Ether technology worth considering.
Great experiement. You forgot to say Tesla claimed that this way can be produced hundreds thousands of horse power with a football field size plant. If you take a look at your setup and what Tesla said to make sure, you have missed few precaution steps. You should try to make capacitor the way Tesla did. You must make sure that it does not leak. Most of capacitors fabricated today don't care about that as they are meant to be used in powered circuits where such losses dont play role so its not that important but for this application it is.
" Most of capacitors fabricated today don't care about that as they are meant to be used in" Ever hear of Nichicon? Sure the Chinese may not care about quality but there are companies that do care and they make precision caps for critical systems. I would trust one of those companies before I would trust a homebrew cap built by some TH-cam educated self proclaimed engineer who has no idea the difference between volts and amps.
@@Elfnetdesigns haha. Tesla has a patent about capacitors and has explained it how its made. Still today they use Tesla method for most demanding applications. Tesla discovery of using oil as an insulator is used in many applications today beside capacitors. Most difficult sounding thing is to make sure all air is excluded from capacitor but today with cheap vacuum pumps its easy to do that and degasing it? Whole point is that capacitor keeps charge and does not leak it in environment much until you want to discharge it into a circuit/battery.
@@domestinger8805 nikola Tesla has two patents on Capacitors. First one was oil based and second improved is paraffin based. Main problem acording to it with capacitors are vacuous spaces. He solve it by creating condenser in vacuum and then finishing it of with 100psi what seems ensured that those spaces don't reappear. He said that produced condensers of most excellent quality. I have checked and today paraffin is rated really high on its dielectric properties but you may try to use other as well.
A crystal radio with a rectified output can collect resonant energy from transmitters and send it to accumulators. Not a lot in any small period of time but over days and weeks, many usable watt-hours.
It's called a hydroelectric dam. Tesla built his free energy devise at Niagara falls. What is bring shown here is an antenna that could receive energy from the Warden cliff transmitting tower that was powered by Niagara falls hydroelectric power station.
Grateful that other people also look for ways to access free energy for our world. If groups of people meditated each day on how our world could have free energy, I bet we would all have access to within our lifetime. Something to think about....
@@tritonbradford1688 Well you can ditch it and build a proper power wall out if 18650 Li-Ion cells salvaged from used laptop battery packs. 3 cells in series = about 12 volts. Wire that into a Li_ION BMS board then into a solar charge controller and get yourself a proper solar panel. Aside from some overhead cost of batteries, solar panel, wire solder, charge controller, etc, that is about as FREE as energy will get. Not trying to be an ass just being realistic. The sun will provide you all the energy you can collect if you have the means to collect it the right way. Now if you want to make a better battery in your project, try crushing the graphite into a powder and mixing it with some acidic liquid, you don't have to use sulfuric acid or something dangerous, simple citric acid from lemons will do for a project test.. make a paste and load that into a zinc or aluminum metal cylinder or whatever, the container should become the negative and you will want to add a carbon rod element that will become your positive. For the paste mix you can experiment with different things like acids, alkaline materials, etc. Just look up how batteries are made online and you will get some ideas. try and steer away from dangerous chemicals though if possible otherwise use proper safety gears while handling and working with such chemicals.
The father off everything make our life better. No others .eve Albert Einstein say. When someone tell him how does feel be the greatest mind . he say ask Nikolai's Tesla
Leonardo da Vinci was 'importing' and translating old Arabic scripts (full of ancient knowledge and inventions) to latin. He was great artist and man of many talents but apparently not an inventor as such. Nicola Tesla on the other hand is one of very few in mankinds history he shaped the world as we know it. Good chanel and good videos👍
I made one of these back in 1982. Photons knock electrons off of the aluminum foil and electrons flow from the ground into the capacitor. That’s all there is to it.
HI guys, its astonishing to find such negative comments on something this important and this simple to actually confirm. Theoretically, we can trust what Nicola tesla has set out in his designs. Theoretically, the various energy systems laid out by many who have pursued in the past SHOULD WORK!. Now just like youll, i am also extremely bitter toward anyone leading the world astray in a time when we the little people need this the most. While we are here bickering about someones design, som parent out there in the dark of night next to candle is holding their child while feeling them take their last breaths of life.Youve never been there, i have. So thats why this is all more important than we think. The fact that the first thing anyone displays in these energy devices is the charging of a phone is a sad display of what we really become and therefore dont deserve the efforts of those who have tried. Mam, whoever you you are, if this really is prelude to something that works, one of us will confirm it.
I used to build basic radio crystals where you can hear a radio broadcast on earphones, without using batteries. You can't call this "FREE ENERGY". What the radio and TV stations emit, we collect in a LC circuit. i,e, the broadcasting Radio stations invested lots of electric power (emitting radio waves) for you to receive an oscillating wave in a electronic circuit. IT IS NOT FREE, you pay for publicity included in the broadcast, and the publicity agency pays the owner of the radio station. Lightnings are also a good source of electric power, that is the source of "Tesla free energy". I see where the "PERPETUAL MOVEMENT concept" comes from.
The other thing that you missed here is that Tesla didn't realise until later in his career that this was tapinginto atmospheric electricity. More research has been done since then and there are ways to make the colection better. Tesla's collector should actually be designed as a cathode rather than an anode, it should have many spike and ionisation points for negative charge from the ground to contact positive charge in the air. Additionally, alitude is key. Experiments with balloons achored at 300 yards found that, at that elevation, with a ground spacing of 1 acre, up to 1.5 KW can be collected in summer and as much as 3 KW could be collected in the winter since the atmosphere is more conducive to the effect. Additional research also found that the need for extreme altitude could also me mitigated by providing high voltage assistance, basically, using a high voltage to suck in the ions and funnel them to you from the environment, basically accelerating the ground attraction.
Okay friends thanks for all the comments here's some little tidbits hints and clues that you can use for taking energy out of the air one you have to understand what the Zamboni pile is once you do you can start to understand free energy Robert Murray Smith channels talks about this if you can find his video. He also says that you can get one kilowatt a voltage out of this device but very little amps. Now here's the secret like a swing this is what the word scalar waves come from understand the word itself it is a scale so we start with the example a swing and at the seat sits a person who toggles her body back and forth with her legs in back this is the little energy that we were talkin about milliwatts if you understand the example, as you tap the peak of the energy you begin to make the energy increase little by little into you get this awesome wave that shouldn't happen but does. If you want to do research on that at Rogue wave, once you hear the scientific evidence on how these waves occur you see that Tesla scalar wave is not only possible have been used in many other scientific experiments. Now let's tell you this my name is Lloyd G stove on I work for Media Library oh, I'm also the person who defined overunity. Now many people disagree would I have been saying for over 31 years about overunity and tries to put in these fake terms so these are the things you must get around to understand the science that's being hidden right before your eyes. Let's do some common sense thinking overunity is a compound word over plus Unity; so how in the world does those two words ever mean perpetual motion they're lying to you they don't relate at all so when you hear my explanation on overunity read my published papers on the history of overunity you'll see that they most definitely don't want you to know anyting about overunity or scalar waves for that matter. Why because they explain away to take milliwatts and scale them into impossible amperage that should be impossible. That's why I mention rogue waves yes and the swing it only takes a small amount of energy 2 tap or spank that larger amount of energy 2 keep that energy going or increase it this is a science that most people haven't look into or study yet they use these methods all the time like keeping a spinning ball spinning on your finger for long periods of time. Swinging from almost Ground Zero without any assistance. Again there are secrets right before your eyes if you are looking but as long as you are buying into perpetual motion controversy and letting people tell you that overunity has something to do with perpetual motion the secret will be lost anyone who takes the time to read these Passage. I'm just a librarian who been working and using this type of energy for years we give out a number almost every time 313-651-5349. If you are shy and you don't want to talk just dropped a text message at 313-777-3031, and you should get a reply free energy is out there and has been used throughout history for millions of years the people who tell you otherwise are helping to keep this a secret, the car company Tesla didn't listen to those type of people and look where he is today remember or just go back and look at the evidence for yourself they told Tesla car company would he was trying to do was impossible and yet he did it you have to break through all these controversies and understand that Nikola Tesla's work is being used every day while at the same time they say he was a pseudoscientist, thank you if you read mine higher rhetoric
I’m getting sick of people unable to replicate properly a device than claiming isn’t working or the output not not worth to pursue further more. Actually this setup can power a house in the winter. Capacitors needs to be chosen in relation with the load, diodes needs to be fast switching under 25 ns and voltage according with the desired output, antenna needs to be a real metal chunk highly polished placed at least 2.5 meters above the ground completely isolated, an ground connection properly done is a must and few modules like this can be connected in parallel … Just compare with a photovoltaic system to see how much power they generate before trashing this system ! Than take in account that this system is working 24/7 with no maintenance needed and power bank would be just 10% compared with a solar electricity system, cost for few diodes and capacitors are a fraction of cost of solar cell Actually with the right setup we can have a mobile solution and we can power electric vehicles easy without huge battery banks which would reduce the cost at least half, no to mention pollution reduced 99%. Some people graduate the school and being just brainwashed, not learning anything … this setup can be done by anyone who truly learned something in school after 10-12 years, and there isn’t anything that break any laws of physics.
Tesla is a prime example of this fact - If you are a genius it doesnt mean you are gonna be rich $ wise and if you are rich it doesnt mean you are a genius !
A good experiment would have an identical capacitor right next to it, connected to nothing, as a control. Capacitors can acquire a space charge just sitting around.
Amusing. Many information. However Tesla noticed, that vibrations are principle of the world. His free energy car is enhanced by electrical vibrations.(?). Wikipedia: Nikola Tesla 10 July 1856 - 7 January 1943. The Tunguska event was a massive explosion 30 June 1908 07:17.
Today, many people are talking about free energy, and how it can help them get off the grid. However, what they don't realize is that free energy has been around for a long time. It's not a new concept by any means. In fact, ether technology development engineers have been using free energy for many years now. One of the best examples of free energy technology is the magnifying transmitter. This is a device that can convert electricity into ether energy, which can then be used to power your home or vehicle. The magnifying transmitter is still in development, but it shows great promise for the future.
There is technolgy developed in netherlands to harness static electricity from air. Right now the efficiency is 105% (device needs initial „charge” to collect static from air)
Tessler knew this and even built the towers to attract the electrostatic in thunderstorms they were destroyed time after time. The problem is confining a average lightning bolt is possible to store the energy without blowing transformers. The issue is that some strikes are 5 million volts , A lighting strike which heats up anything it touches in a instance to more than 6000c and can actually create pure plasma that's impossible to control .For us to gather energy from the air by wind is far safer and more reliable until we can work out how not to overload the grid system also static in the air caused by charged particle from the sun already overload our antiquated network every time it activity increases on the sun so you would need to factor that into the equation when considering such a feat
@@wayneparkinson4558 it's not impossible just improbable... harnessing lightning Requires opposite windings calculation of gaussian density...in other words you build klystron coil array wind to left hand flow of ions Instead of right hand rule of electron flow...MOST of lightning is Ion Energy...humans are Binary brain creatures bound to euclidean geometry...
Tesla writes in the Brooklyn Eagle newspaper on July 10th 1932: "I have harnessed the cosmic rays and caused them to operate a motive device... More than 25 years ago I began my efforts to harness the cosmic rays and I can now state that I have succeeded in operating a motive device by means of them. I will tell you in the most general way, the cosmic ray ionizes the air, setting free many charges ions and electrons. These charges are captured in a condenser which is made to discharge through the circuit of the motor. I have hopes of building my motor on a large scale, but circumstances have not been favorable to carrying out my plan".
This device probably works on the basis of the photoelectric effect where electrons are lifted out of the metal (you need high enough frequency, so probably only the UV light of the sun contributes significantly). That results in a positve charge in the metal and electrons flow from the capacitor to the metal creating a charge imbalance -> voltage
Lovely video content! Apologies for the intrusion, I am interested in your opinion. Have you heard about - Malmenjaay Unexposed Inspiration (should be on google have a look)? It is a smashing one off guide for discovering your mayan day sign and the clues it has to your future without the hard work. Ive heard some pretty good things about it and my mate at very last got cool success with it.
You clearly dont know what you're talking about. Electrons getting "lifted" from the metal is literally electricity, everything else you said is unnecessary. Also if you actually dis that you'd realise that you just described a Van de Graaff generator or tesla coil. It take energy to move the electrons away from the metal so whatever energy you get is what you paid for.
@@Devonte-w8o No the energy of the photons of light provides the energy to the electrons that they need to be released out of the metal. If you lay down any piece of metal into the sunlight, some electrons are expelled due to the UV-light (Google photoelectric effect for this). This is totally different to a Van de Graf generator which works by friction (triboelectric effect). What is shown here in the video is basically a solar panel but not as efficient. Normal solar panels use semiconductor materials to efficiently generate energy. The energy comes from the sun through photons. It is basically free. But it is not a perpetuum mobile because it is powerd by an external source, the sun.
you can use it all you want. The truth is, you won't get a whole lot of juice from this experiment. almost as much as the solar panel that lights up your neighbors patio... But still, It's free and in abundance
We can use perpetual motion added with the coils and magnets configured in such a way not unlike how it looks at cern and the other induction engine that tesla created. I've seen ppl create these themselves as its only able to be a DIY project n can't be sold. But we can take the petrol engine off of our own home generator and then use golf cart batteries to store the energy in. We want to build a coil and match the impedance to be that of a house or car so to run it on the energy I've seen ppl make these n have run their entire hojse on and or car for 2yrs and going. But we never hear from them again many inventors. That took the basic idea and built on it and made a car run or a house. We get the right voltages calculated and it dictates the shape and size it doesn't need be that big. But the idea is we have magnetically pushed and pulled like perpetual motion machines but the kind that use magnets and they are set up in such a way that when it's done being pulled by 1 its pushed by the next. This way we can setup our coils to get excited electrons from the speed of the magnets spinning with copper coils configured in the proper ways. We can already see the design in these images in this video. The on off switch is the thing that spins faster n faster lol. So idk its kind of a thing u set and forget it just keeps going generating more power and when we hook it to where the other petrol engine was it works better lol and is quiet and clean zero pollution this way. But why have we been burning coal so long n worse nuclear as "clean " $$! Sad they were upset they couldn't put a meter on it.. not realizing all the inventions they could have done so to after that was achieved! Lit the world in the 1900s there's still video of it but they're scrubbing it fast why? So much we've been lied to about. I wish I coukd remember more about the designs but its it'sits been there about 15yrs now and I'd been remembering it from watching a video once yrs ago and trying to make it in real life but it keep getting taken down and suppressed. Which really makes me think its on to something big.
Instead of aluminum try copper and instead of a thin sheet, use a coil design on an insulated frame. It’s not the surface area that you’re looking for but the concentration of conductor material. Try a Christmas tree form Made of insulated material and use the copper to weave the positive collector.
@@domestinger8805: The video is misleading, because it seems to indicate that incident rays are what's powering it, even though she even remarks that it keeps functioning at night. In reality what's actually happening is that you're essentially "harvesting" atmospheric ions, which are arranged in an atmospheric electric field with a gradient of ~100 V/m near the ground, but much higher further up. To increase the energy harvested in this way what you want to do is to have the antenna as high up in the air as possible, and to have as much surface area on it as possible (a flat rectangle as shown here is a rather lousy design, better to make a fractal antenna or just use a dense copper mesh arranged in a spherical or cylindrical shape). During times of more atmospheric activity both in terms of wind and electrical activity (as during thunderstorms, but also during moist weather in general, the equatorial tropics would probably be a great place for something like this) there will be a lot more energy available. You essentially have to think about it in terms of how much charge you can collect on the antenna, which primarily comes from charged particles in the air rather than radiation; thus why more wind (more particles moving across it) and moister weather (more charge being conducted between the particles themselves) is better. If you do this you should also make sure to either use high-voltage capacitors or to regularly discharge the capacitors once they reach a certain voltage, because the voltage very high up will be quite large (as mentioned above, the field is ~100 V/m on a fair day near the ground, under a thunderstorm high up the field can easily reach 1000 V/m or more, for a total potential of tens of thousands of volts depending on how high up your collecting antenna is). These days you can get high-energy supercapacitors very cheaply, would probably be a perfect fit for this kind of thing, but they are rated for a low voltage in comparison, so you'd really have to make sure to monitor and discharge it (luckily they'd take a fair amount of time to reach their rated voltage, relatively speaking, so that shouldn't be too difficult).
About Nikola Tesla self-driving motor is that all you need to do is plug into the ground if in fact that truly works that could have great potential I myself am trying to reproduce a similar device
I think 7.83hz is a saturated signal so design around 40k ft. Of 8gauge at a height of 45ft. 300sq ft air core ariel antenna. With super capacitors should be able to do it now. 180 2.3v. 5000f
Radiant energy is particles that have been charged either positive or negative. As particles strike the antenna they leaved these they add or delete the charges on the plate. This way an average charge is reached. Tesla must have came to this conclusion. However he mentioned the sea of energy. CERN mentioned that all of space is full of electrons. The need to only be gathered. Is this a good enough clue?
might wanna try a capacitor value available in Tesla's time, i suggest a few metal cans or buckets that fit into eachother with an insulator between them (cloth or something) with waay back then tech a 2200uF cap would be like as big as a truck?
I've only seen a few mentions of Tesla's work on capacitors, they were another subject he was doing inventing on. I have a reprint book from early 1900s on how to build capacitors and they showed examples of some of the largest caps ive ever seen, I didnt know that industries built them that big. One had to be 8 to 10 feet long and near 2 ft. wide. I thought i had read in one of my Tesla books that he was building some kind of apparatus deep into the ground below the wardenclif tower that was supposed to act as a capacitor. I have to find my book again.
Tyvm for this video I have a lot to think about! I can't help but think a lot of what u said is required to make it feasible starts to sound like a tree. Good height, grounding, and surface area of a football field in the leaves :D
Insulate the air terminal and make it bigger!😀😀😀😀 thanks for sharing!! 😀😀😀😀😀😀😀😀😀😀😀😀😀oh yeah and remember to create a resonant circuit! There is a little secret to have the energy constantly flowing and powering your home!!!!!!!!! I ca explain more if you would like!! 😀😀😀😀
Hola creo que la antena esta mal la placa metálica debe estar aislada del aire y ademas en el circuito falta un diodo que rectifique la c.a captada para que se pueda almacenar en el capacitor porque este es de c.c. Por otra parte el circuito orginal de nikola tesla utilizaba un capacitor de ac que una vez cargado por medio de un dispositivo mecánico lo descargaba en el devanado primario de un transformador por eso el sistema trabajaba en corriente alterna . Saludos !!!
There is so much wrong with the experiment. Tesla said heavily insulate the plate, use high tension/high voltage capacitors, and to have everything insulated for high voltage. You are also supposed to charge the plate negative. People replicate tesla's patents and completely leave out very important details. Also the plate should be suspended in the air as high as possible.
@@fredflintstone3318 No I've actually done the experiments, it was before my TH-cam channel and before I was making videos. Right now I'm working on the tesla turbine to utilize the heat energy that can be created with this system. I will re-build it in the future now that I have funding to build it properly. The only reason I'm upset is people say the technology doesn't work, and it's not because it doesn't work, it's that people build it wrong.
The technology is interesting. The best bit is I've just watched a video offering the secret and easy to make plans. ( I had nothing better to do) Anyway, all this is at a special reduced price for a limited time , only $ 49 And that's proper US $.
interesting ! i am wonder , those particles of energy did they go through the panel of aluminum? what if you can use multiple panels as energy colectors , 3 or 4 , the one in front of the other, to eliminate the case of particle penetration and loosing eficiency, in that case if we loose energy with one , you must see with 4 layer of colector an increase of charging voltage of your mesurment for the same time of exposure....
There is so much wrong with the experiment. Tesla said heavily insulate the plate, use high tension/high voltage capacitors, and to have everything insulated for high voltage. You are also supposed to charge the plate negative. People replicate tesla's patents and completely leave out very important details.
@@conniehurney9546 Absolutely, I followed the directions exactly It was a very crude set up, but the concept was proven with amazing results. I am returning to the research after I finish the tesla turbine research.
Thanks for the video. However, I must ask, considering we live in an era where there are skyscrapers and high rise buildings surrounding us that have roofs averaging the size of a quarter of a football field, would it not make sense to have these receivers on the sides as well as on the roofs of buildings? Would that not make an efficient amount of energy?
In most cases it would make a lot more sense to cover these areas with solar panels and combine them with a pack of batteries. It would make for a significantly more efficient system than Teslas, as explained in the video.
@@domestinger8805: Not really, because those tall buildings are not insulated from earth, and it wouldn't be practical at all to make them so considering that they're made out of metal. Thus they continuously act to neutralize the atmospheric potential gradient, and can't be used for harvesting themselves.
Great video and excellent explanation. I bet this has big improvement potential with all the new materials being invented. Btw we always hear your voice but never seen you in the video. Bet it makes a lot of us curious. 🤔
Stick a good ion collector high enough up in the air, and you can harvest way more power than that. A few hundred meters up and we're talking tens of kV in a conductive enough part of the atmosphere to establish a continuous current. I saw someone who had collectors just ~40 meters high, and during disturbed weather they achieved a peak of ~40 kV of continuous ~30 mA current; that's 1.2 kW. Go even higher up and you'll start getting power like that even in fair weather, and far surpass it in disturbed weather. The ultimately goal of this technology would be to use lasers to establish plasma channels and harvest energy from the ionosphere that way, or something incredibly dramatic like setting up standing lightning bolts between the ionosphere and ground. When thinking about what is really being done here in those terms it's easy to see that we're talking about a lot of potential power.
Okay friends thanks for all the comments here's some little tidbits hints and clues that you can use for taking energy out of the air one you have to understand what the Zamboni pile is once you do you can start to understand free energy Robert Murray Smith channels talks about this if you can find his video. He also says that you can get one kilowatt a voltage out of this device but very little amps. Now here's the secret like a swing this is what the word scalar waves come from understand the word itself it is a scale so we start with the example a swing and at the seat sits a person who toggles her body back and forth with her legs in back this is the little energy that we were talkin about milliwatts if you understand the example, as you tap the peak of the energy you begin to make the energy increase little by little into you get this awesome wave that shouldn't happen but does. If you want to do research on that at Rogue wave, once you hear the scientific evidence on how these waves occur you see that Tesla scalar wave is not only possible have been used in many other scientific experiments. Now let's tell you this my name is Lloyd G stove on I work for Media Library oh, I'm also the person who defined overunity. Now many people disagree would I have been saying for over 31 years about overunity and tries to put in these fake terms so these are the things you must get around to understand the science that's being hidden right before your eyes. Let's do some common sense thinking overunity is a compound word over plus Unity; so how in the world does those two words ever mean perpetual motion they're lying to you they don't relate at all so when you hear my explanation on overunity read my published papers on the history of overunity you'll see that they most definitely don't want you to know anyting about overunity or scalar waves for that matter. Why because they explain away to take milliwatts and scale them into impossible amperage that should be impossible. That's why I mention rogue waves yes and the swing it only takes a small amount of energy 2 tap or spank that larger amount of energy 2 keep that energy going or increase it this is a science that most people haven't look into or study yet they use these methods all the time like keeping a spinning ball spinning on your finger for long periods of time. Swinging from almost Ground Zero without any assistance. Again there are secrets right before your eyes if you are looking but as long as you are buying into perpetual motion controversy and letting people tell you that overunity has something to do with perpetual motion the secret will be lost anyone who takes the time to read these Passage. I'm just a librarian who been working and using this type of energy for years we give out a number almost every time 313-651-5349. If you are shy and you don't want to talk just dropped a text message at 313-777-3031, and you should get a reply free energy is out there and has been used throughout history for millions of years the people who tell you otherwise are helping to keep this a secret, the car company Tesla didn't listen to those type of people and look where he is today remember or just go back and look at the evidence for yourself they told Tesla car company would he was trying to do was impossible and yet he did it you have to break through all these controversies and understand that Nikola Tesla's work is being used every day while at the same time they say he was a pseudoscientist, thank you if you read mine higher rhetoric
observation iş really good but öne point missed iş heigrh ,how high u go the current increases also youneed lot better antenna and grounding but good experment congratulations ....also capacitor needs calculations not random element
Its already done by Engr. Elias its a free generator and seing in market very soon i watch this because video because i did not believe at first. Now i know what he did is really free energy.
I think the antenna just needs to be redesigned old world technology used a brass ball with Mercury. I think mercury has the capability of pulling energy from The atmosphere like a better antenna.
@paulanderson7796 We might conceptualize a theory that amalgamates both contemporary and speculative technologies to mitigate the effects of electromagnetic fields (EMFs), particularly those emanating from high-frequency radio waves like 2.4 GHz and 5G, along with electrosmog. **Theoretical Framework: Resonant Frequency Neutralization** At the heart of this theoretical approach is the principle of resonant frequencies, a concept Tesla explored extensively in his work. Every physical object, including the electromagnetic waves that permeate our environment, has a natural frequency at which it vibrates. By harnessing this principle, we could theoretically design a system that emits counter-frequencies to neutralize unwanted EMF radiation. This system would involve several key components and steps: 1. **Detection and Analysis**: Utilize advanced sensors to detect and analyze the frequency, amplitude, and phase of the ambient EMF radiation in real-time. These sensors would need to be highly sensitive and capable of discerning between different sources of EMFs to target specific frequencies, such as those from Wi-Fi routers or 5G cell towers. 2. **Counter-Frequency Generation**: Based on the analysis, a counter-frequency generator would create a wave that matches the detected EMF radiation in frequency but is inverted in phase (180 degrees out of phase). When two waves are perfectly out of phase, they have the potential to cancel each other out, a phenomenon known as destructive interference. 3. **Adaptive Resonance Control**: To ensure the system remains effective despite the dynamic nature of EMF sources (which may vary in frequency and intensity), an adaptive control mechanism would adjust the counter-frequencies in real-time. This would require sophisticated algorithms capable of rapid analysis and adjustment to changing electromagnetic conditions. 4. **Energy Harvesting and Utilization**: In a nod to Tesla's vision of wireless energy transmission, the system could also incorporate technologies for harvesting energy from the neutralized EMF waves. This harvested energy could then be stored or immediately used, turning potential environmental hazards into a source of clean energy. 5. **Protective Zone Creation**: By strategically placing such systems in homes, workplaces, or public spaces, we could create zones with significantly reduced EMF levels. These zones would provide sanctuaries from the omnipresent electromagnetic pollution of modern life. **Technological and Material Considerations** To realize this theory, advancements in materials science, particularly in metamaterials, which can bend electromagnetic waves in unusual ways, would be pivotal. Additionally, the development of highly efficient energy harvesting and storage technologies would be necessary to manage the energy captured from neutralized EMFs. **Challenges and Ethical Considerations** Implementing such a system poses significant technical challenges, including the need for precise control over the counter-frequencies and the scalability of the technology to cover large areas. Moreover, there are ethical considerations related to the manipulation of electromagnetic environments, including potential impacts on wildlife and the need for regulatory frameworks to govern the use of such technologies. In conclusion, while this theoretical approach draws heavily from both Tesla's visionary ideas and modern technological advancements, its realization would require significant innovation and interdisciplinary collaboration. Nonetheless, in the spirit of Tesla's unyielding optimism in the face of challenge, such a pursuit epitomizes the quest for harmony between humanity's technological aspirations and the natural world. Expanding upon the conceptual framework of neutralizing and subsequently harnessing electromagnetic fields (EMFs), let's delve into a theory for the energy harvesting component. This theory will integrate both established principles and emerging technologies in the realm of energy conversion and storage, aiming to transform ambient EMFs into usable electrical energy. **Theory of Electromagnetic Energy Harvesting** The core idea is to employ a combination of advanced metamaterials, resonant circuits, and nanotechnology to capture and convert the energy from EMFs into a form that can be stored or used directly by electrical devices. 1. **Metamaterials for Enhanced EMF Interaction**: Metamaterials, engineered to have properties not found in naturally occurring materials, can be designed to interact with EMFs in highly efficient ways. By structuring these materials at a scale smaller than the wavelength of the target EMFs, they can be made to resonate with specific frequencies, significantly enhancing the absorption of energy. This resonant absorption process can be optimized for the frequencies of interest, such as those from wireless communication networks. 2. **Resonant Circuits for Energy Conversion**: Once the energy is absorbed by the metamaterials, it can be transferred to resonant circuits specifically tuned to the same frequencies. These circuits can efficiently convert the absorbed electromagnetic energy into electrical energy. The use of high-quality factor (Q-factor) resonators would minimize energy loss during conversion, ensuring that a substantial portion of the absorbed energy is available for use. 3. **Nanotechnology for Energy Harvesting and Storage**: Advances in nanotechnology could play a crucial role in both the harvesting and storage of energy. Nanoscale devices and materials offer the potential for high efficiency and low-energy loss in the conversion process. For example, nanostructured solar cells can convert a broader range of the electromagnetic spectrum into electrical energy, and similar principles could be applied to EMF energy harvesting. Additionally, nano-enhanced supercapacitors or batteries could be developed to store the harvested energy with high density and rapid charge-discharge cycles, making the energy readily available for use. 4. **Integration into the Built Environment**: To maximize the potential of this energy harvesting system, it could be integrated into the fabric of the built environment-buildings, roads, and even clothing. For instance, paints and building materials embedded with metamaterials and nanogenerators could capture EMF energy from the environment, converting and storing it for use in powering smart devices, lighting, and other electrical systems. 5. **Self-Powering Electronic Devices**: In a more direct application, electronic devices could be equipped with miniaturized versions of this energy harvesting system, allowing them to draw power from ambient EMFs. This would pave the way for self-charging mobile phones, laptops, and wearable technology, significantly reducing their dependence on traditional energy sources. **Challenges and Potential Impacts** While theoretically compelling, this approach to EMF energy harvesting and utilization faces significant scientific and engineering challenges. The development of materials and devices capable of efficiently capturing and converting EMF energy at a large scale requires breakthroughs in materials science, nanotechnology, and electrical engineering. Furthermore, addressing concerns regarding the environmental and health impacts of deploying such technologies on a wide scale would be paramount. In conclusion, by envisioning a system that not only mitigates the potential negative effects of electromagnetic pollution but also transforms this ubiquitous energy source into a valuable asset, we align with a Tesla-inspired vision for a future where technology harmonizes with the natural world to enhance human life. This theoretical exploration invites us to imagine a world where the boundaries of energy harvesting are expanded, driving innovation and sustainability in the service of humanity.
Any high school kid with a year of electronics classes behind them could tell you why the meter value changed, and any college level electrical engineering or physics student has a better understanding of the principles of electromagnetism than Tesla did. Really-if you want to stand on the shoulders of giants, you should follow the examples that worked, not the ones that didn't. LOL
i think if tesla was alive today with our technology he would be creating things we couldnt imagen
he did in his time but they destroy or hide everything u culdnt imagine
Of course he would
If reincarnation exists then he is
The things we have today they probably had 500 years ago but we didn’t know about it just like they have stuff we cant think possible is being hidden
@11:14PM teslas ideas when he was really young and created DC motors. That's all, I think?
The plate needs to be flat, the way you have it set up it disperses the energy due to the arc in the antenna. The energy is coming straight on.
Point it to the East, because we travel through the aether and the spin of the Earth causes us to spin eastward.
The higher you get it the more you will gather from the impedance difference.
A minor amperage 2-3V A.C. added to the metal plate causes the antenna to gather energy from 10x the area of the physical antenna.
The ground must be the same size as the antenna and buried 12-18" under the ground with a Good insulated wire to one leg of the capacitor.
Wet the earth around the ground if the earth is dry.
Give us a video after these modifications.
Blessings!
If it’s 10x what is the expected area?
@@yehboi6646 1 sq ft of antenna collects 10 sq ft of energy
Shiny side of aluminum foil outwards. If using a metal plate, shine the eastward facing side ultrashiny (300 grit or finer 1200 is better)
I used a simple wire about 15 feet long to catch radio stations in my crystal radio.
@@God-s_Kingdom what are u using to add the added voltage?
If everything is tuned properly, and in balance, and your grounding rod is deep and the antenna is high enough, everything made in high quality, with a large array of tank circuits, you should see a worthwhile amount of energy accumulating nonstop.
What if you use more then one rod will it increase the energy ????
Sorry also what if there spaced out ????? To cover more area?
@@ChrisChris-sj7zm:
The video is misleading, because it seems to indicate that incident rays are what's powering it, even though she even remarks that it keeps functioning at night. In reality what's actually happening is that you're essentially "harvesting" atmospheric ions, which are arranged in an atmospheric electric field with a gradient of ~100 V/m near the ground, but much higher further up.
To increase the energy harvested in this way what you want to do is to have the antenna as high up in the air as possible, and to have as much surface area on it as possible (a flat rectangle as shown here is a rather lousy design, better to make a fractal antenna or just use a dense copper mesh arranged in a spherical or cylindrical shape). During times of more atmospheric activity both in terms of wind and electrical activity (as during thunderstorms, but also during moist weather in general, the equatorial tropics would probably be a great place for something like this) there will be a lot more energy available.
You essentially have to think about it in terms of how much charge you can collect on the antenna, which primarily comes from charged particles in the air rather than radiation; thus why more wind (more particles moving across it) and moister weather (more charge being conducted between the particles themselves) is better.
If you do this you should also make sure to either use high-voltage capacitors or to regularly discharge the capacitors once they reach a certain voltage, because the voltage very high up will be quite large (as mentioned above, the field is ~100 V/m on a fair day near the ground, under a thunderstorm high up the field can easily reach 1000 V/m or more, for a total potential of tens of thousands of volts depending on how high up your collecting antenna is). These days you can get high-energy supercapacitors very cheaply, would probably be a perfect fit for this kind of thing, but they are rated for a low voltage in comparison, so you'd really have to make sure to monitor and discharge it (luckily they'd take a fair amount of time to reach their rated voltage, relatively speaking, so that shouldn't be too difficult).
@@ChrisChris-sj7zm *they're
Please, add a signal diode (like 1N60, BAT41, etc) between the antenna and the capacitor with the anode on the antenna side. Alternativelly you can put the diode between the antenna and ground, in parallel with the capacitor, with the cattode connected to the antenna side. I bet you will get much more charge in the same period of time.
Not one diode. Use 4 to make a full-wave bridge rectifier. If they are germanium, you have the "Joe Tate Ambient Power Module" circuit. You can use 6 diodes or even more.
Agreed 200%
How does adding a diode in parallel reverse the flow of current? I’m intrigued. Could two circuits be made, one series, one parallel and be connected in a way?
@jondelaire sorry my friend, dont be intrigued any more, you are right. I wrote my comment long time ago and I dont remember why I said that. Diode in parallel will not work. Just in serie or using a full-wave bridge as suggested by Chuck. I remember doing it when I was a kid, 40 years ago. Only difference is that I used a tank circuit tuned to AM broadcast band. Accumulated energy was used to power an AM receiver that worked with a couple of transistors and headsets and using the same tank circuit. It was basically a small radio that worked without batteries, published in the well known "Lúpin" magazine in Argentina. Regards! Adrián
Yes make a crystal radio set.. That is what you all need. just add a crystal set earpeice to the mix and get the sports scores
You don't actually need the aluminum foil. Just having a wire up high in the air harvests IONs and generates the same charge. Another Nikola Tesla invention, one of many many innovations
@Tristan Arnold yes it does dum dum. try it before discounting.
There is so much wrong with the experiment. Tesla said heavily insulate the plate, use high tension/high voltage capacitors, and to have everything insulated for high voltage. You are also supposed to charge the plate negative. People replicate tesla's patents and completely leave out very important details.
Maybe its just a piece of his puzzle and not about wires or plates in the sky.
@@ImYourProblem Experiments teach the truth. I am speaking from experiments. It works exactly as tesla describes.
Yea of course it works.. you really gonna put a plate high in the sky to get any usable energy from it? Where does tesla state to do that? This patent is only a clue, a partial circuit, a TUNED "reciever".. dont focus so much on the diagram details.. its not about pulling dc current from ground to sky..
Great to see a video about this topic that is not biassed in either direction.
As a sidenote, the electrolytic capacitor may have accumulated some charge just from being heated by the sun to a higher temperature than what it was before.
The directions in his plans also say to insulate the metal plate. yours looks to be taped or glued to a pc of cardboard or something with your wire only tapped to the aluminum foil. Maybe a larger flat pc of steel or aluminum that is painted on all sides with rubber to insulate it, and the wire soldered to the plate? Higher is better.
All energy is free - it's the cost of, storing it, getting it to the end user, in a usable form, useful to that particular piece of equipment that costs.
When computer first came out, it was pricy and took up a lot of space. And what do we have now?
What you think is costly can change in no time. Open your mind.
XClent, I couldn't explain it better.
What is cost other then a made up currency system , all that’ stuff is free humans just decided god forbid anybody moves a finger for the greater good if they can’t profit from it , the irony is we would all profit of off working together and ending currency
As of now most energy comes from fossil fuels which arent free... it cost money to get people to do the work to mine the coal which is then burnt for energy.
@@thesouthernnortheast4991 oh no a communists anyways
Take a large inductance transformer coil with 300mh and 30mh. Get a
second one just like it. Now hook a piezo element across the the ground
and a high antenna wire. Connect one 300mh coil across the piezo. You
may connected piezos in series to get higher voltage. Then connect the
30mh coil to each other. Then measure the output across the free 300mh
coil for free energy.
Super! Thank you very much. Nikola Tesla is genius.
he was a genius. at the time he is invented this technology, there was nor radio energy waves. if you do this today, you can get arrested, because you steal energy from the radio station and create a hole in the radiowave net. and they know where the hole is. they can track you down.
With the ions flowing thru, some charges on the caps remain. BUT, a better idea is to have the antenna to ground circuit oscillate and thus help in pumping more and more ions from the antenna and ground. If the antenna and ground plate are brought to a much higher voltage (> 100 volts), there can be slight ionization on the metal improving its ability to interface with the ions present nearby. The oscillation, or AC currents, can be converted to DC via germanium diodes (rate for high voltage), bridge rectifier, and charge a super-cap with the DC side.
Build your "better idea" and post a video of your experiment. I'm literally dying to see it.
I have experimented with this using an oscillator source, and the capacitors I worked with basically became "self charging" in the manner you speak of. I had a large cap, 50,000 mfd at 60v and it would self charge to around 3 volts ⚡️
Nice spark with 50,000 mfd 🤪
@@RGRundeRGRound charge time?
@@RGRundeRGRound Serious question, link to instructions please, I want to do this as well. It will be a fun side project to my electrostatic generator.
Thomas moray improved upon this method to get a large amount of power out.
6:40 some suggestions for improvement. Wires are too long and too much resistance. Need short wires with high gauge, low resistance. Need a much better connection to ground. There should be a large iron plate buried deep underground. You want the ions from the ground to take the path you create to the sky (like the Great Pyramid of Gizah). Then, have a super cap and a boost converter to boost the low voltage to the target voltage. Consider also the Tate ambient power module circuit which uses germanium diodes. That circuit really works!!!
Certainly one shouldn't use wires longer then nessesary, and it is lower gauge wires that are thicker with lower resistance. But here, resistance in the wire here is not the issue for its poor performance, and trying to optimize the wire thickness for lower resistance to capture more power is a case study in diminishing returns.
For example, if you have two setups in identical conditions. But one setup having a copper wire 10× cross section area than the other setup's copper wire of the same length, meaning the wire will cost maybe 10× more because it uses 10× copper, but is still unlikely to increase the power collected over a year by .0001%
Yes a boost converter can convert low voltage to a higher voltage but boost converters use an oscillator circuit to pulse width modulate a signal to the switch just after the inductor in the boost converter. That oscillator will use up more power than the setup in the video collected, and fail to boost anything.
One does not need iron buried deep underground. A typical grounding rod should be sufficient unless one lives in a desert. One can also use their water pipes as a good earth ground.
The real limiting factor is that power available is a function of surface area and height of the collector. increasing both will do far more than spending additional money to optimise a lower resistance in the collector cable or improve the ground. Even then, it's not worth to spend $100 to get maybe $0.01 worth of electricity over a year.
free energy here is little more than a lab curiosity. not a viable means to usefull energy.
@@kreynolds1123 were not talking about collecting voltage from the air, that's why you need an iron plate collector in the ground
@@domestinger8805 Yes the original commentor in this discussion thread was talking about collecting energy from moving electrons in the ground to the sky.
The original commentor was suggesting improvements via lowering resistance from earth to sky. My comment was essentually indirectly saying that using the copper wires wasn't the source of most of the resistance in the circuit, that the negligible modest against from a thicker wire would be costly without a significant gain in performance, and most any existing earth ground will have sufficiently low resistance.
I'm saying now that most of the resistance in the circuit comes from ion flow to the current collector surface area in the air.
Yes a thicker wire has a greater surface area but that increases by the square while the cost of copper increases by the cubic volume for a given length, where as a longer thinner wire has a much greater surface area and reasomably low enough resistance for modest currents.
Curious how the location on our planet (and its magnetic fields) affects the charge... Try it at Stonehenge and the Pyramids.
Great Video clip! Excuse me for the intrusion, I am interested in your initial thoughts. Have you ever tried - Malmenjaay Unexposed Inspiration (probably on Google)? It is a good exclusive product for discovering your mayan day sign and the clues it has to your future without the headache. Ive heard some amazing things about it and my work colleague finally got cool success with it.
Okay friends thanks for all the comments here's some little tidbits hints and clues that you can use for taking energy out of the air one you have to understand what the Zamboni pile is once you do you can start to understand free energy Robert Murray Smith channels talks about this if you can find his video. He also says that you can get one kilowatt a voltage out of this device but very little amps. Now here's the secret like a swing this is what the word scalar waves come from understand the word itself it is a scale so we start with the example a swing and at the seat sits a person who toggles her body back and forth with her legs in back this is the little energy that we were talkin about milliwatts if you understand the example, as you tap the peak of the energy you begin to make the energy increase little by little into you get this awesome wave that shouldn't happen but does. If you want to do research on that at Rogue wave, once you hear the scientific evidence on how these waves occur you see that Tesla scalar wave is not only possible have been used in many other scientific experiments. Now let's tell you this my name is Lloyd G stove on I work for Media Library oh, I'm also the person who defined overunity. Now many people disagree would I have been saying for over 31 years about overunity and tries to put in these fake terms so these are the things you must get around to understand the science that's being hidden right before your eyes. Let's do some common sense thinking overunity is a compound word over plus Unity; so how in the world does those two words ever mean perpetual motion they're lying to you they don't relate at all so when you hear my explanation on overunity read my published papers on the history of overunity you'll see that they most definitely don't want you to know anyting about overunity or scalar waves for that matter. Why because they explain away to take milliwatts and scale them into impossible amperage that should be impossible. That's why I mention rogue waves yes and the swing it only takes a small amount of energy 2 tap or spank that larger amount of energy 2 keep that energy going or increase it this is a science that most people haven't look into or study yet they use these methods all the time like keeping a spinning ball spinning on your finger for long periods of time. Swinging from almost Ground Zero without any assistance. Again there are secrets right before your eyes if you are looking but as long as you are buying into perpetual motion controversy and letting people tell you that overunity has something to do with perpetual motion the secret will be lost anyone who takes the time to read these Passage. I'm just a librarian who been working and using this type of energy for years we give out a number almost every time 313-651-5349. If you are shy and you don't want to talk just dropped a text message at 313-777-3031, and you should get a reply free energy is out there and has been used throughout history for millions of years the people who tell you otherwise are helping to keep this a secret, the car company Tesla didn't listen to those type of people and look where he is today remember or just go back and look at the evidence for yourself they told Tesla car company would he was trying to do was impossible and yet he did it you have to break through all these controversies and understand that Nikola Tesla's work is being used every day while at the same time they say he was a pseudoscientist, thank you if you read mine higher rhetoric
Tesla was the most unarguably intelligent person to ever walk on face of the earth
False trump is
@@sinisternightmare405 False jöergen is
john von neumann is though
Edison stole his spotlight Edison was no where as intelligent as tesla tesla thinking was on another level
I also got 0.2V at 15ft. My antenna was homemade stainless steel sea urchin type. I used the joule thief circuit to harvest the accumulated charge. Happy experimenting!
You will not get 50 to 60 MHz out of the Earth the energy will be 2.72 mHz and will need to be converted
@@obviouslytwo4u Ok. Energy in mHz is fine.
@@obviouslytwo4u:
When harvesting ions from the air as in these experiments, what you're getting is direct current, not alternating current, so there is no frequency.
Tesla's Wardencliffe tower was designed to receive energy wirelessly but through a different receiving method. However, the tower was 190 feet tall to reach a minimal point above the earth to be at a sufficient distance where the atmosphere as it's own capacitance, between upper atmospheric charge and the ground, are well enough separated that a sufficient usable voltage can naturally occur, and therefore, better harvested using the antenna and ground connection at such a height. Interestingly, the modern day replication of Tesla's work by a company in Texas USA named Texzon, also has towers this same height. Although both Tesla's and Texzon technology both use surface wave propagation, the atmosphere at this height separates the charge.
You really think so? I read that large gasoline or diesel motors were part of Wardencliffe. Hard to prove it after that cuck Morgan destroyed both it and Tesla.
You have to have resonance with shuman resonance
if u connect a joule thief circuit between the antenna and load, the voltage and current both will increase
Thank you for taking the time to do this experiment, show it, and explain it. I hope you keep doing this. Knowledge is important. Doing is important. One without the other is a plant without sunlight. Blessings, health, and safety to all....
Radiant energy (free energy) is not all energy from sunlight!
The term "free energy" has been used by ether technology development engineers for many years, but it is not a pure concept. It is the energy extracted from Ether. The Magnifying Transmitter is a cutting edge Ether technology worth considering.
@@ultimateenergizerguide467 I think you've misunderstood his comment...
Great experiement. You forgot to say Tesla claimed that this way can be produced hundreds thousands of horse power with a football field size plant. If you take a look at your setup and what Tesla said to make sure, you have missed few precaution steps. You should try to make capacitor the way Tesla did. You must make sure that it does not leak. Most of capacitors fabricated today don't care about that as they are meant to be used in powered circuits where such losses dont play role so its not that important but for this application it is.
Jesi im objasnio :)
" Most of capacitors fabricated today don't care about that as they are meant to be used in"
Ever hear of Nichicon?
Sure the Chinese may not care about quality but there are companies that do care and they make precision caps for critical systems. I would trust one of those companies before I would trust a homebrew cap built by some TH-cam educated self proclaimed engineer who has no idea the difference between volts and amps.
@@Elfnetdesigns haha. Tesla has a patent about capacitors and has explained it how its made. Still today they use Tesla method for most demanding applications. Tesla discovery of using oil as an insulator is used in many applications today beside capacitors. Most difficult sounding thing is to make sure all air is excluded from capacitor but today with cheap vacuum pumps its easy to do that and degasing it? Whole point is that capacitor keeps charge and does not leak it in environment much until you want to discharge it into a circuit/battery.
@@darkobul1 can you point me in the direction of learning how to make completely optimal capacitors?
@@domestinger8805 nikola Tesla has two patents on Capacitors. First one was oil based and second improved is paraffin based. Main problem acording to it with capacitors are vacuous spaces. He solve it by creating condenser in vacuum and then finishing it of with 100psi what seems ensured that those spaces don't reappear. He said that produced condensers of most excellent quality. I have checked and today paraffin is rated really high on its dielectric properties but you may try to use other as well.
A crystal radio with a rectified output can collect resonant energy from transmitters and send it to accumulators.
Not a lot in any small period of time but over days and weeks, many usable watt-hours.
It's called a hydroelectric dam. Tesla built his free energy devise at Niagara falls. What is bring shown here is an antenna that could receive energy from the Warden cliff transmitting tower that was powered by Niagara falls hydroelectric power station.
Grateful that other people also look for ways to access free energy for our world. If groups of people meditated each day on how our world could have free energy, I bet we would all have access to within our lifetime. Something to think about....
3:26 where did you find ussr made capacitor?
Put strips of graphene parallel 1 inch wide, and every 2 inches down the aluminum foil. Graphene draws electricity to itself.
Congratulations you are creating a crude dry cell battery...
@@Elfnetdesigns ...What is your recommendation to make the project better? She is looking to get more out of the panel.
@@tritonbradford1688 Well you can ditch it and build a proper power wall out if 18650 Li-Ion cells salvaged from used laptop battery packs. 3 cells in series = about 12 volts. Wire that into a Li_ION BMS board then into a solar charge controller and get yourself a proper solar panel. Aside from some overhead cost of batteries, solar panel, wire solder, charge controller, etc, that is about as FREE as energy will get. Not trying to be an ass just being realistic. The sun will provide you all the energy you can collect if you have the means to collect it the right way.
Now if you want to make a better battery in your project, try crushing the graphite into a powder and mixing it with some acidic liquid, you don't have to use sulfuric acid or something dangerous, simple citric acid from lemons will do for a project test.. make a paste and load that into a zinc or aluminum metal cylinder or whatever, the container should become the negative and you will want to add a carbon rod element that will become your positive. For the paste mix you can experiment with different things like acids, alkaline materials, etc. Just look up how batteries are made online and you will get some ideas. try and steer away from dangerous chemicals though if possible otherwise use proper safety gears while handling and working with such chemicals.
@@Elfnetdesigns...Great idea! Hopefully she see's this, and takes your advice. I think it's a great idea.👍
@@Elfnetdesigns Ha ha ha, pretty good.
The father off everything make our life better. No others .eve Albert Einstein say. When someone tell him how does feel be the greatest mind . he say ask Nikolai's Tesla
@@cheesemccheese5780 no tesla never hated him
Leonardo da Vinci was 'importing' and translating old Arabic scripts (full of ancient knowledge and inventions) to latin.
He was great artist and man of many talents but apparently not an inventor as such.
Nicola Tesla on the other hand is one of very few in mankinds history he shaped the world as we know it.
Good chanel and good videos👍
I made one of these back in 1982. Photons knock electrons off of the aluminum foil and electrons flow from the ground into the capacitor. That’s all there is to it.
Does it charge faster during the day because of energy emitted by the sun, or because radio stations reduce their power at night? (Maybe both)
Good reasoning, maybe you are an engineer.
@@vperez4796 I'm an EET actually, good guess - I just graduated :)
HI guys, its astonishing to find such negative comments on something this important and this simple to actually confirm. Theoretically, we can trust what Nicola tesla has set out in his designs. Theoretically, the various energy systems laid out by many who have pursued in the past SHOULD WORK!. Now just like youll, i am also extremely bitter toward anyone leading the world astray in a time when we the little people need this the most. While we are here bickering about someones design, som parent out there in the dark of night next to candle is holding their child while feeling them take their last breaths of life.Youve never been there, i have. So thats why this is all more important than we think. The fact that the first thing anyone displays in these energy devices is the charging of a phone is a sad display of what we really become and therefore dont deserve the efforts of those who have tried. Mam, whoever you you are, if this really is prelude to something that works, one of us will confirm it.
Fuel free system nice effort.
If one take all pain then all world is be happy. He prove it . He is legend
I used to build basic radio crystals where you can hear a radio broadcast on earphones, without using batteries. You can't call this "FREE ENERGY". What the radio and TV stations emit, we collect in a LC circuit. i,e, the broadcasting Radio stations invested lots of electric power (emitting radio waves) for you to receive an oscillating wave in a electronic circuit. IT IS NOT FREE, you pay for publicity included in the broadcast, and the publicity agency pays the owner of the radio station. Lightnings are also a good source of electric power, that is the source of "Tesla free energy". I see where the "PERPETUAL MOVEMENT concept" comes from.
The other thing that you missed here is that Tesla didn't realise until later in his career that this was tapinginto atmospheric electricity. More research has been done since then and there are ways to make the colection better.
Tesla's collector should actually be designed as a cathode rather than an anode, it should have many spike and ionisation points for negative charge from the ground to contact positive charge in the air. Additionally, alitude is key.
Experiments with balloons achored at 300 yards found that, at that elevation, with a ground spacing of 1 acre, up to 1.5 KW can be collected in summer and as much as 3 KW could be collected in the winter since the atmosphere is more conducive to the effect.
Additional research also found that the need for extreme altitude could also me mitigated by providing high voltage assistance, basically, using a high voltage to suck in the ions and funnel them to you from the environment, basically accelerating the ground attraction.
Thank you so much for explained wonderfull invention of Nikola Tesla...
I put a bridge rectifier , from antenna, and, ground to the AC in and get dc out.
I call THE RECTIFIER (ElectroBoom's alter ego) to rectify this free energy.
is this on his subreddit?
Do not take ElectroBoom out to scare every poor person.
ElectroBoom, he gets paid to suppress technology, ensure his wealth.
@@immaterialpower5808 i assume you are joking?
Okay friends thanks for all the comments here's some little tidbits hints and clues that you can use for taking energy out of the air one you have to understand what the Zamboni pile is once you do you can start to understand free energy Robert Murray Smith channels talks about this if you can find his video. He also says that you can get one kilowatt a voltage out of this device but very little amps. Now here's the secret like a swing this is what the word scalar waves come from understand the word itself it is a scale so we start with the example a swing and at the seat sits a person who toggles her body back and forth with her legs in back this is the little energy that we were talkin about milliwatts if you understand the example, as you tap the peak of the energy you begin to make the energy increase little by little into you get this awesome wave that shouldn't happen but does. If you want to do research on that at Rogue wave, once you hear the scientific evidence on how these waves occur you see that Tesla scalar wave is not only possible have been used in many other scientific experiments. Now let's tell you this my name is Lloyd G stove on I work for Media Library oh, I'm also the person who defined overunity. Now many people disagree would I have been saying for over 31 years about overunity and tries to put in these fake terms so these are the things you must get around to understand the science that's being hidden right before your eyes. Let's do some common sense thinking overunity is a compound word over plus Unity; so how in the world does those two words ever mean perpetual motion they're lying to you they don't relate at all so when you hear my explanation on overunity read my published papers on the history of overunity you'll see that they most definitely don't want you to know anyting about overunity or scalar waves for that matter. Why because they explain away to take milliwatts and scale them into impossible amperage that should be impossible. That's why I mention rogue waves yes and the swing it only takes a small amount of energy 2 tap or spank that larger amount of energy 2 keep that energy going or increase it this is a science that most people haven't look into or study yet they use these methods all the time like keeping a spinning ball spinning on your finger for long periods of time. Swinging from almost Ground Zero without any assistance. Again there are secrets right before your eyes if you are looking but as long as you are buying into perpetual motion controversy and letting people tell you that overunity has something to do with perpetual motion the secret will be lost anyone who takes the time to read these Passage. I'm just a librarian who been working and using this type of energy for years we give out a number almost every time 313-651-5349. If you are shy and you don't want to talk just dropped a text message at 313-777-3031, and you should get a reply free energy is out there and has been used throughout history for millions of years the people who tell you otherwise are helping to keep this a secret, the car company Tesla didn't listen to those type of people and look where he is today remember or just go back and look at the evidence for yourself they told Tesla car company would he was trying to do was impossible and yet he did it you have to break through all these controversies and understand that Nikola Tesla's work is being used every day while at the same time they say he was a pseudoscientist, thank you if you read mine higher rhetoric
Call him and say to rectify
I’m getting sick of people unable to replicate properly a device than claiming isn’t working or the output not not worth to pursue further more. Actually this setup can power a house in the winter. Capacitors needs to be chosen in relation with the load, diodes needs to be fast switching under 25 ns and voltage according with the desired output, antenna needs to be a real metal chunk highly polished placed at least 2.5 meters above the ground completely isolated, an ground connection properly done is a must and few modules like this can be connected in parallel …
Just compare with a photovoltaic system to see how much power they generate before trashing this system ! Than take in account that this system is working 24/7 with no maintenance needed and power bank would be just 10% compared with a solar electricity system, cost for few diodes and capacitors are a fraction of cost of solar cell
Actually with the right setup we can have a mobile solution and we can power electric vehicles easy without huge battery banks which would reduce the cost at least half, no to mention pollution reduced 99%.
Some people graduate the school and being just brainwashed, not learning anything … this setup can be done by anyone who truly learned something in school after 10-12 years, and there isn’t anything that break any laws of physics.
Thank you so much. That cleared up a lot of questions for me. :-)
Tesla is a prime example of this fact - If you are a genius it doesnt mean you are gonna be rich $ wise and if you are rich it doesnt mean you are a genius !
A good experiment would have an identical capacitor right next to it, connected to nothing, as a control. Capacitors can acquire a space charge just sitting around.
They charge just by sitting around?
@@marcelkuiper5474 Not to any useful level. We're measuring miniscule amounts of current here.
Very nice video my friend thank you. This may one day be useful for us mankind. I believe dealing with Terraforming.
He knows the gods who gave him his knowledge
Amusing. Many information. However Tesla noticed, that vibrations are principle of the world. His free energy car is enhanced by electrical vibrations.(?). Wikipedia: Nikola Tesla 10 July 1856 - 7 January 1943. The Tunguska event was a massive explosion 30 June 1908 07:17.
Today, many people are talking about free energy, and how it can help them get off the grid. However, what they don't realize is that free energy has been around for a long time. It's not a new concept by any means. In fact, ether technology development engineers have been using free energy for many years now.
One of the best examples of free energy technology is the magnifying transmitter. This is a device that can convert electricity into ether energy, which can then be used to power your home or vehicle. The magnifying transmitter is still in development, but it shows great promise for the future.
There is technolgy developed in netherlands to harness static electricity from air. Right now the efficiency is 105% (device needs initial „charge” to collect static from air)
Tessler knew this and even built the towers to attract the electrostatic in thunderstorms they were destroyed time after time. The problem is confining a average lightning bolt is possible to store the energy without blowing transformers. The issue is that some strikes are 5 million volts , A lighting strike which heats up anything it touches in a instance to more than 6000c and can actually create pure plasma that's impossible to control .For us to gather energy from the air by wind is far safer and more reliable until we can work out how not to overload the grid system also static in the air caused by charged particle from the sun already overload our antiquated network every time it activity increases on the sun so you would need to factor that into the equation when considering such a feat
@@wayneparkinson4558 it's not impossible just improbable... harnessing lightning Requires opposite windings calculation of gaussian density...in other words you build klystron coil array wind to left hand flow of ions Instead of right hand rule of electron flow...MOST of lightning is Ion Energy...humans are Binary brain creatures bound to euclidean geometry...
Please let me know what kind of PC board or project 🙏or kids that we can do or buy with boats and spares
3:52 All it is ,, is a form of solar power. I wonder if I used this grounding technique on todays solar panels would I get more power.
No
Tesla writes in the Brooklyn Eagle newspaper on July 10th 1932: "I have harnessed the cosmic rays and caused them to operate a motive device... More than 25 years ago I began my efforts to harness the cosmic rays and I can now state that I have succeeded in operating a motive device by means of them. I will tell you in the most general way, the cosmic ray ionizes the air, setting free many charges ions and electrons. These charges are captured in a condenser which is made to discharge through the circuit of the motor. I have hopes of building my motor on a large scale, but circumstances have not been favorable to carrying out my plan".
For perpetual motion to work, you must incorporate a honey bee collecting pollen into your design...
Great experiment, I imagined perhaps a gang tuning cap with a spark gap that might make a tank circuit with the radiant energy from collector antenna
@simpsons Bart there's a notable difference at night between full moon and no moon
A spark gap with only 0.2 volts? Good luck with that.
Awesome and very informative on some of tesla's work thank you!
This device probably works on the basis of the photoelectric effect where electrons are lifted out of the metal (you need high enough frequency, so probably only the UV light of the sun contributes significantly). That results in a positve charge in the metal and electrons flow from the capacitor to the metal creating a charge imbalance -> voltage
Lovely video content! Apologies for the intrusion, I am interested in your opinion. Have you heard about - Malmenjaay Unexposed Inspiration (should be on google have a look)? It is a smashing one off guide for discovering your mayan day sign and the clues it has to your future without the hard work. Ive heard some pretty good things about it and my mate at very last got cool success with it.
You clearly dont know what you're talking about. Electrons getting "lifted" from the metal is literally electricity, everything else you said is unnecessary. Also if you actually dis that you'd realise that you just described a Van de Graaff generator or tesla coil. It take energy to move the electrons away from the metal so whatever energy you get is what you paid for.
@@Devonte-w8o No the energy of the photons of light provides the energy to the electrons that they need to be released out of the metal. If you lay down any piece of metal into the sunlight, some electrons are expelled due to the UV-light (Google photoelectric effect for this). This is totally different to a Van de Graf generator which works by friction (triboelectric effect).
What is shown here in the video is basically a solar panel but not as efficient. Normal solar panels use semiconductor materials to efficiently generate energy. The energy comes from the sun through photons. It is basically free. But it is not a perpetuum mobile because it is powerd by an external source, the sun.
@@ChannelTheLizard . Do you like arguing with yourself?
an old capacitor made by CCCP its a peace of collection for museum. did you fond it at the butome of the Caspian sea?
I have many one
@@mishikogelashvili8443 Cool :)
And there starting a Paris climate accord we have always had free energy they wont let us use it
That’s a lie
you can use it all you want. The truth is, you won't get a whole lot of juice from this experiment. almost as much as the solar panel that lights up your neighbors patio... But still, It's free and in abundance
Tesla developed this concept way past this. But the really useful patents, we are unable to see.
Play a video game called “Close to the Sun” you’ll get a good idea of these patents.
We can use perpetual motion added with the coils and magnets configured in such a way not unlike how it looks at cern and the other induction engine that tesla created. I've seen ppl create these themselves as its only able to be a DIY project n can't be sold. But we can take the petrol engine off of our own home generator and then use golf cart batteries to store the energy in. We want to build a coil and match the impedance to be that of a house or car so to run it on the energy I've seen ppl make these n have run their entire hojse on and or car for 2yrs and going. But we never hear from them again many inventors. That took the basic idea and built on it and made a car run or a house.
We get the right voltages calculated and it dictates the shape and size it doesn't need be that big. But the idea is we have magnetically pushed and pulled like perpetual motion machines but the kind that use magnets and they are set up in such a way that when it's done being pulled by 1 its pushed by the next. This way we can setup our coils to get excited electrons from the speed of the magnets spinning with copper coils configured in the proper ways. We can already see the design in these images in this video. The on off switch is the thing that spins faster n faster lol. So idk its kind of a thing u set and forget it just keeps going generating more power and when we hook it to where the other petrol engine was it works better lol and is quiet and clean zero pollution this way. But why have we been burning coal so long n worse nuclear as "clean " $$! Sad they were upset they couldn't put a meter on it.. not realizing all the inventions they could have done so to after that was achieved! Lit the world in the 1900s there's still video of it but they're scrubbing it fast why? So much we've been lied to about. I wish I coukd remember more about the designs but its it'sits been there about 15yrs now and I'd been remembering it from watching a video once yrs ago and trying to make it in real life but it keep getting taken down and suppressed. Which really makes me think its on to something big.
Instead of aluminum try copper and instead of a thin sheet, use a coil design on an insulated frame.
It’s not the surface area that you’re looking for but the concentration of conductor material.
Try a Christmas tree form Made of insulated material and use the copper to weave the positive collector.
Explain this better
@@domestinger8805:
The video is misleading, because it seems to indicate that incident rays are what's powering it, even though she even remarks that it keeps functioning at night. In reality what's actually happening is that you're essentially "harvesting" atmospheric ions, which are arranged in an atmospheric electric field with a gradient of ~100 V/m near the ground, but much higher further up.
To increase the energy harvested in this way what you want to do is to have the antenna as high up in the air as possible, and to have as much surface area on it as possible (a flat rectangle as shown here is a rather lousy design, better to make a fractal antenna or just use a dense copper mesh arranged in a spherical or cylindrical shape). During times of more atmospheric activity both in terms of wind and electrical activity (as during thunderstorms, but also during moist weather in general, the equatorial tropics would probably be a great place for something like this) there will be a lot more energy available.
You essentially have to think about it in terms of how much charge you can collect on the antenna, which primarily comes from charged particles in the air rather than radiation; thus why more wind (more particles moving across it) and moister weather (more charge being conducted between the particles themselves) is better.
If you do this you should also make sure to either use high-voltage capacitors or to regularly discharge the capacitors once they reach a certain voltage, because the voltage very high up will be quite large (as mentioned above, the field is ~100 V/m on a fair day near the ground, under a thunderstorm high up the field can easily reach 1000 V/m or more, for a total potential of tens of thousands of volts depending on how high up your collecting antenna is). These days you can get high-energy supercapacitors very cheaply, would probably be a perfect fit for this kind of thing, but they are rated for a low voltage in comparison, so you'd really have to make sure to monitor and discharge it (luckily they'd take a fair amount of time to reach their rated voltage, relatively speaking, so that shouldn't be too difficult).
About Nikola Tesla self-driving motor is that all you need to do is plug into the ground if in fact that truly works that could have great potential I myself am trying to reproduce a similar device
I hear you jumped off your window balcony too. R.I.P. sir.
@@LosAngelesWeedSmoker really?
I think 7.83hz is a saturated signal so design around 40k ft. Of 8gauge at a height of 45ft. 300sq ft air core ariel antenna. With super capacitors should be able to do it now. 180 2.3v. 5000f
Radiant energy is particles that have been charged either positive or negative. As particles strike the antenna they leaved these they add or delete the charges on the plate. This way an average charge is reached. Tesla must have came to this conclusion. However he mentioned the sea of energy. CERN mentioned that all of space is full of electrons. The need to only be gathered. Is this a good enough clue?
My favourite chanel always！
I know why
Instead of a capacitor could you use a 12volt battery?
Mhm.
no
Todays led bulbs are becoming popular please make a simple led driver circuit for repairing faulty led bulbs. Thank you
might wanna try a capacitor value available in Tesla's time, i suggest a few metal cans or buckets that fit into eachother with an insulator between them (cloth or something)
with waay back then tech a 2200uF cap would be like as big as a truck?
I've only seen a few mentions of Tesla's work on capacitors, they were another subject he was doing inventing on.
I have a reprint book from early 1900s on how to build capacitors and they showed examples of some of the largest caps ive ever seen, I didnt know that industries built them that big.
One had to be 8 to 10 feet long and near 2 ft. wide.
I thought i had read in one of my Tesla books that he was building some kind of apparatus deep into the ground below the wardenclif tower that was supposed to act as a capacitor. I have to find my book again.
Tyvm for this video I have a lot to think about! I can't help but think a lot of what u said is required to make it feasible starts to sound like a tree. Good height, grounding, and surface area of a football field in the leaves :D
Bruh it's fake 🤦♂️
@@Devonte-w8o good boy now sit.
@@chancebutler6472 There is no free energy, try for yourself
Nice video
Insulate the air terminal and make it bigger!😀😀😀😀 thanks for sharing!! 😀😀😀😀😀😀😀😀😀😀😀😀😀oh yeah and remember to create a resonant circuit! There is a little secret to have the energy constantly flowing and powering your home!!!!!!!!! I ca explain more if you would like!! 😀😀😀😀
Help me powermy home please. Howmuch will it cost
😂 volatage is too low at mili amps how can u power your home with that
I think all antena,reciever has to be same frequency of the planet to get some results(maybe use good grounding to tune earth frequency)
i just left two 200V 680uf caps on my desk not connect to anything and they charged up to 4+ volts
Hola creo que la antena esta mal la placa metálica debe estar aislada del aire y ademas en el circuito falta un diodo que rectifique la c.a captada para que se pueda almacenar en el capacitor porque este es de c.c.
Por otra parte el circuito orginal de nikola tesla utilizaba un capacitor de ac que una vez cargado por medio de un dispositivo mecánico lo descargaba en el devanado primario de un transformador por eso el sistema trabajaba en corriente alterna . Saludos !!!
There is so much wrong with the experiment. Tesla said heavily insulate the plate, use high tension/high voltage capacitors, and to have everything insulated for high voltage. You are also supposed to charge the plate negative. People replicate tesla's patents and completely leave out very important details. Also the plate should be suspended in the air as high as possible.
@@fredflintstone3318 No I've actually done the experiments, it was before my TH-cam channel and before I was making videos. Right now I'm working on the tesla turbine to utilize the heat energy that can be created with this system. I will re-build it in the future now that I have funding to build it properly. The only reason I'm upset is people say the technology doesn't work, and it's not because it doesn't work, it's that people build it wrong.
The technology is interesting.
The best bit is I've just watched a video offering the secret and easy to make plans. ( I had nothing better to do)
Anyway, all this is at a special reduced price for a limited time , only $ 49
And that's proper US $.
interesting ! i am wonder , those particles of energy did they go through the panel of aluminum? what if you can use multiple panels as energy colectors , 3 or 4 , the one in front of the other, to eliminate the case of particle penetration and loosing eficiency, in that case if we loose energy with one , you must see with 4 layer of colector an increase of charging voltage of your mesurment for the same time of exposure....
There is so much wrong with the experiment. Tesla said heavily insulate the plate, use high tension/high voltage capacitors, and to have everything insulated for high voltage. You are also supposed to charge the plate negative. People replicate tesla's patents and completely leave out very important details.
@@iEnergySupply have you made one does it work?
@@conniehurney9546 Absolutely, I followed the directions exactly It was a very crude set up, but the concept was proven with amazing results. I am returning to the research after I finish the tesla turbine research.
@@iEnergySupply will you keep me posted on your results please. On both efforts.
If you had placed a bridge rectifier before the capacitor the voltage will increase.
Weather it is sunny or not shouldn't matter.
Thanks for the video. However, I must ask, considering we live in an era where there are skyscrapers and high rise buildings surrounding us that have roofs averaging the size of a quarter of a football field, would it not make sense to have these receivers on the sides as well as on the roofs of buildings? Would that not make an efficient amount of energy?
In most cases it would make a lot more sense to cover these areas with solar panels and combine them with a pack of batteries. It would make for a significantly more efficient system than Teslas, as explained in the video.
The answer is yes.
@@domestinger8805:
Not really, because those tall buildings are not insulated from earth, and it wouldn't be practical at all to make them so considering that they're made out of metal. Thus they continuously act to neutralize the atmospheric potential gradient, and can't be used for harvesting themselves.
3:24 Epic Soviet Union capacitor.
*USSR anthem plays*
Nikola Tesla was a Serb.
Great video and excellent explanation. I bet this has big improvement potential with all the new materials being invented. Btw we always hear your voice but never seen you in the video. Bet it makes a lot of us curious. 🤔
You have missed one very important part that Tesla mentioned but did not explain fully.
so sad he could calculate energy so well.. his systems product like 1w power. Still great engineer of all time
Stick a good ion collector high enough up in the air, and you can harvest way more power than that. A few hundred meters up and we're talking tens of kV in a conductive enough part of the atmosphere to establish a continuous current. I saw someone who had collectors just ~40 meters high, and during disturbed weather they achieved a peak of ~40 kV of continuous ~30 mA current; that's 1.2 kW.
Go even higher up and you'll start getting power like that even in fair weather, and far surpass it in disturbed weather. The ultimately goal of this technology would be to use lasers to establish plasma channels and harvest energy from the ionosphere that way, or something incredibly dramatic like setting up standing lightning bolts between the ionosphere and ground. When thinking about what is really being done here in those terms it's easy to see that we're talking about a lot of potential power.
Could be useful to power small low power sensors for wide area data collecting.....
Excellent explanation and beautiful voice to, well produced video.
If we had Nicko Tesla's alternative current towers. This would charge massive power to supply whole towns
Alternating current? That's quite conventional throughout the world.
FInd out how workes detefon. It is a radio witout source of energy
Add a tuner to your antenna the resident frequency when tuned in properly will give you more electricity.
Please say, How can we make a simlar larger version more efficient.
The metal sheet suspended in the air should be insulated according to the patent, and your aluminum foil isn't.
You need to put the plate up way high hundreds, thousands of feet. Bigger pane
Watch out for airplanes.
Really interesting!
Okay friends thanks for all the comments here's some little tidbits hints and clues that you can use for taking energy out of the air one you have to understand what the Zamboni pile is once you do you can start to understand free energy Robert Murray Smith channels talks about this if you can find his video. He also says that you can get one kilowatt a voltage out of this device but very little amps. Now here's the secret like a swing this is what the word scalar waves come from understand the word itself it is a scale so we start with the example a swing and at the seat sits a person who toggles her body back and forth with her legs in back this is the little energy that we were talkin about milliwatts if you understand the example, as you tap the peak of the energy you begin to make the energy increase little by little into you get this awesome wave that shouldn't happen but does. If you want to do research on that at Rogue wave, once you hear the scientific evidence on how these waves occur you see that Tesla scalar wave is not only possible have been used in many other scientific experiments. Now let's tell you this my name is Lloyd G stove on I work for Media Library oh, I'm also the person who defined overunity. Now many people disagree would I have been saying for over 31 years about overunity and tries to put in these fake terms so these are the things you must get around to understand the science that's being hidden right before your eyes. Let's do some common sense thinking overunity is a compound word over plus Unity; so how in the world does those two words ever mean perpetual motion they're lying to you they don't relate at all so when you hear my explanation on overunity read my published papers on the history of overunity you'll see that they most definitely don't want you to know anyting about overunity or scalar waves for that matter. Why because they explain away to take milliwatts and scale them into impossible amperage that should be impossible. That's why I mention rogue waves yes and the swing it only takes a small amount of energy 2 tap or spank that larger amount of energy 2 keep that energy going or increase it this is a science that most people haven't look into or study yet they use these methods all the time like keeping a spinning ball spinning on your finger for long periods of time. Swinging from almost Ground Zero without any assistance. Again there are secrets right before your eyes if you are looking but as long as you are buying into perpetual motion controversy and letting people tell you that overunity has something to do with perpetual motion the secret will be lost anyone who takes the time to read these Passage. I'm just a librarian who been working and using this type of energy for years we give out a number almost every time 313-651-5349. If you are shy and you don't want to talk just dropped a text message at 313-777-3031, and you should get a reply free energy is out there and has been used throughout history for millions of years the people who tell you otherwise are helping to keep this a secret, the car company Tesla didn't listen to those type of people and look where he is today remember or just go back and look at the evidence for yourself they told Tesla car company would he was trying to do was impossible and yet he did it you have to break through all these controversies and understand that Nikola Tesla's work is being used every day while at the same time they say he was a pseudoscientist, thank you if you read mine higher rhetoric
observation iş really good but öne point missed iş heigrh ,how high u go the current increases also youneed lot better antenna and grounding but good experment congratulations ....also capacitor needs calculations not random element
Not so. The type of antenna and materials used can greatly increase efficiency. So too for capacitors.
Yes but how many amps?
Its already done by Engr. Elias its a free generator and seing in market very soon i watch this because video because i did not believe at first. Now i know what he did is really free energy.
Nice
his grand father was priest in a the greek orthodox community in serbia
, seems that his name derive from ' Thessaly ' Θεσσαλία
He's father whas priest in Serbian orthodox church.He goes to Amerika bcz. he didint whant to be priest like hes father.🇷🇸❤
I think the antenna just needs to be redesigned old world technology used a brass ball with Mercury. I think mercury has the capability of pulling energy from The atmosphere like a better antenna.
If we could use radio waves to convert to energy could we maybe deplete harmful fields of radiation etc?
How?
@paulanderson7796 We might conceptualize a theory that amalgamates both contemporary and speculative technologies to mitigate the effects of electromagnetic fields (EMFs), particularly those emanating from high-frequency radio waves like 2.4 GHz and 5G, along with electrosmog.
**Theoretical Framework: Resonant Frequency Neutralization**
At the heart of this theoretical approach is the principle of resonant frequencies, a concept Tesla explored extensively in his work. Every physical object, including the electromagnetic waves that permeate our environment, has a natural frequency at which it vibrates. By harnessing this principle, we could theoretically design a system that emits counter-frequencies to neutralize unwanted EMF radiation. This system would involve several key components and steps:
1. **Detection and Analysis**: Utilize advanced sensors to detect and analyze the frequency, amplitude, and phase of the ambient EMF radiation in real-time. These sensors would need to be highly sensitive and capable of discerning between different sources of EMFs to target specific frequencies, such as those from Wi-Fi routers or 5G cell towers.
2. **Counter-Frequency Generation**: Based on the analysis, a counter-frequency generator would create a wave that matches the detected EMF radiation in frequency but is inverted in phase (180 degrees out of phase). When two waves are perfectly out of phase, they have the potential to cancel each other out, a phenomenon known as destructive interference.
3. **Adaptive Resonance Control**: To ensure the system remains effective despite the dynamic nature of EMF sources (which may vary in frequency and intensity), an adaptive control mechanism would adjust the counter-frequencies in real-time. This would require sophisticated algorithms capable of rapid analysis and adjustment to changing electromagnetic conditions.
4. **Energy Harvesting and Utilization**: In a nod to Tesla's vision of wireless energy transmission, the system could also incorporate technologies for harvesting energy from the neutralized EMF waves. This harvested energy could then be stored or immediately used, turning potential environmental hazards into a source of clean energy.
5. **Protective Zone Creation**: By strategically placing such systems in homes, workplaces, or public spaces, we could create zones with significantly reduced EMF levels. These zones would provide sanctuaries from the omnipresent electromagnetic pollution of modern life.
**Technological and Material Considerations**
To realize this theory, advancements in materials science, particularly in metamaterials, which can bend electromagnetic waves in unusual ways, would be pivotal. Additionally, the development of highly efficient energy harvesting and storage technologies would be necessary to manage the energy captured from neutralized EMFs.
**Challenges and Ethical Considerations**
Implementing such a system poses significant technical challenges, including the need for precise control over the counter-frequencies and the scalability of the technology to cover large areas. Moreover, there are ethical considerations related to the manipulation of electromagnetic environments, including potential impacts on wildlife and the need for regulatory frameworks to govern the use of such technologies.
In conclusion, while this theoretical approach draws heavily from both Tesla's visionary ideas and modern technological advancements, its realization would require significant innovation and interdisciplinary collaboration. Nonetheless, in the spirit of Tesla's unyielding optimism in the face of challenge, such a pursuit epitomizes the quest for harmony between humanity's technological aspirations and the natural world.
Expanding upon the conceptual framework of neutralizing and subsequently harnessing electromagnetic fields (EMFs), let's delve into a theory for the energy harvesting component. This theory will integrate both established principles and emerging technologies in the realm of energy conversion and storage, aiming to transform ambient EMFs into usable electrical energy.
**Theory of Electromagnetic Energy Harvesting**
The core idea is to employ a combination of advanced metamaterials, resonant circuits, and nanotechnology to capture and convert the energy from EMFs into a form that can be stored or used directly by electrical devices.
1. **Metamaterials for Enhanced EMF Interaction**: Metamaterials, engineered to have properties not found in naturally occurring materials, can be designed to interact with EMFs in highly efficient ways. By structuring these materials at a scale smaller than the wavelength of the target EMFs, they can be made to resonate with specific frequencies, significantly enhancing the absorption of energy. This resonant absorption process can be optimized for the frequencies of interest, such as those from wireless communication networks.
2. **Resonant Circuits for Energy Conversion**: Once the energy is absorbed by the metamaterials, it can be transferred to resonant circuits specifically tuned to the same frequencies. These circuits can efficiently convert the absorbed electromagnetic energy into electrical energy. The use of high-quality factor (Q-factor) resonators would minimize energy loss during conversion, ensuring that a substantial portion of the absorbed energy is available for use.
3. **Nanotechnology for Energy Harvesting and Storage**: Advances in nanotechnology could play a crucial role in both the harvesting and storage of energy. Nanoscale devices and materials offer the potential for high efficiency and low-energy loss in the conversion process. For example, nanostructured solar cells can convert a broader range of the electromagnetic spectrum into electrical energy, and similar principles could be applied to EMF energy harvesting. Additionally, nano-enhanced supercapacitors or batteries could be developed to store the harvested energy with high density and rapid charge-discharge cycles, making the energy readily available for use.
4. **Integration into the Built Environment**: To maximize the potential of this energy harvesting system, it could be integrated into the fabric of the built environment-buildings, roads, and even clothing. For instance, paints and building materials embedded with metamaterials and nanogenerators could capture EMF energy from the environment, converting and storing it for use in powering smart devices, lighting, and other electrical systems.
5. **Self-Powering Electronic Devices**: In a more direct application, electronic devices could be equipped with miniaturized versions of this energy harvesting system, allowing them to draw power from ambient EMFs. This would pave the way for self-charging mobile phones, laptops, and wearable technology, significantly reducing their dependence on traditional energy sources.
**Challenges and Potential Impacts**
While theoretically compelling, this approach to EMF energy harvesting and utilization faces significant scientific and engineering challenges. The development of materials and devices capable of efficiently capturing and converting EMF energy at a large scale requires breakthroughs in materials science, nanotechnology, and electrical engineering. Furthermore, addressing concerns regarding the environmental and health impacts of deploying such technologies on a wide scale would be paramount.
In conclusion, by envisioning a system that not only mitigates the potential negative effects of electromagnetic pollution but also transforms this ubiquitous energy source into a valuable asset, we align with a Tesla-inspired vision for a future where technology harmonizes with the natural world to enhance human life. This theoretical exploration invites us to imagine a world where the boundaries of energy harvesting are expanded, driving innovation and sustainability in the service of humanity.
Român 👏
Any high school kid with a year of electronics classes behind them could tell you why the meter value changed, and any college level electrical engineering or physics student has a better understanding of the principles of electromagnetism than Tesla did.
Really-if you want to stand on the shoulders of giants, you should follow the examples that worked, not the ones that didn't.
LOL
Nicely explained ,Thank you 👍👍👍👍
As a free born Englishman I claim my free electricity and free beer too. Lets not forget that!