in my country if you have xenon bulbs you need headlight washers because every factory xenon car has it and if you dont you either have to remove bulbs during registration or install headlight washers...
Lol my Lexus rx300 has factory xenons and no headlight washers, idiots in that country, headlights dont need washers its not a windshield, if they get a tad dirty wash the damn car 😂
May I know what did you spray on the reflector to clean it? I've dealt with lots of reflectors before and some aged reflectors couldn't even take a simple water wipes, it just comes off.
Very nice retro, I noticed a bit of unfilled space with JB Weld between the projector and the back of the reflector, is that not going to make the projector somewhat rattles inside the housing given it is a heavy weight projector so the speak. Great job overall.
Я чего то не допонимаю, или он 300 граммовую линзу на клей (холодную сварку) посадил? Она же на первой же кочке отвалится. Нужно крепить через шпильки в отражатель.
Tell me please. What substance you used to lock the lens in the reflector? And it is not dangerous to such a large lens mount only to the reflector? why you have not fixed on the bolts?
My Friend, I had a question? The slope point on the reference line is facing left. But you did it by turning the slope to the right. Can you please explain this? Thank you.
Thanks for the comeback my friend! In the video you taped the cutting line to the right on the wall. But the break, that is, the slope is to the left. After you attached the lens, the cutting line crossed to the left and the diffraction to the right. I could not understand this. Please explain, or was it not right-hand drive? Thanks
Wow, that's some hard ass reflector. We once tried to clean the reflector of a jetta mk4, and the damn thing got scratched all over. It was a bummer...
***** from this video I understand that it isn't necessary to take the alignment from 20 ft, a closer is fine ? in your case it did turns good, right ? what distance was it ? Thanks.
Retrofitlab great video for the DYI.I am planning to buy the FX-R 3" projector and would need your advice on the Shroud.I dont want to trim a lot on the shroud. So your recommendation would be of great help. Was thinking of the Gatling Gun 2.0. Your thoughts please. What shroud was used in this video? Apollo?
so i finished retrofitting one side and after doing so, i get this weird greenish glow on my headlights. all i did was paint the shrouds and corner amber piece matte black and i doubt its because of that. is it the projector itself giving off this greenish tint on my lens?
If my old headlight uses an H11 , and the new lens uses D3S HID bulbs lets say i don't understand how will i power up the D3S news bulb with my OEM H11 connector ??? and what will i specially use for an HID system ??
We use a regular "window cleaning". But actually the OEM chrome in some headlights is very fragile and comes off when you touch it with anything other than air :-)
i see there are gaps on top and bottom of the FX-Rs. even though they are small gaps, light can still be lost. would it be a good idea to seal the gaps completely or is there a reason for the gaps?
FYI this is only possible if you headlight reflectors have a flat bottom. Most OEM lights sit at an angle and must be aligned on the car itself, which makes it much harder.
Even if it's at an angle, you still align it to the factory line on the wall at the angle the stock cutoff displayed. Once mounted it will be straight. Just match what it displayed.
It seems this model with halogen headlights already has projectors. And in that case, these projectors probably won't fit. And we don't have info on which will fit, sorry.
+Retrofitlab how do you suggest on adjusting the roational alignment using nut & bolt before putting the jb weld? do i just hold the projectors while it's on and mark the holes to be drilled?
What if i wanted to install projectors for my 10 years old Halogen projector lens ?? is there a video for that ?? ( installing a projector in place of an OEM projector )
It's a surface cleaner. But the chrome on the reflectors can react quite bad, so before you do this, test the cleaner on a small and/or not visible surface
Yes it will hold forever :) Once cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled and will withstand temperatures of up to 500 degrees F / 260 C.
It is possible uitilizar this projector in the C4 PALLAS lighthouse? I saw that the quality is superior to Miromoto H1 Anxious hope your answer! Hugs! Romao Moita
Why did you install a LHD cutoff when the factory beams were RHD cutoff? Was the car imported to another country? This Is extremely dangerous if the cutoff is on the wrong side!
Thanks, this video is about 8 years old so there are better HID xenon and bi-led projectors now. Only some Bi-led projectors are more powerful and good HID projectors with quality bulbs are still very good.
You will definitely not blind upcoming traffic, the light pattern is even better than original headlights! See the results: th-cam.com/video/YGaSY9P8Oko/w-d-xo.html
![How To Install Retrofit Projectors With Bi-Xenon [10 Steps]](http://i.ytimg.com/vi/aesyBC6sSjY/mqdefault.jpg)
in my country if you have xenon bulbs you need headlight washers because every factory xenon car has it and if you dont you either have to remove bulbs during registration or install headlight washers...
What country
For example Poland
Lol my Lexus rx300 has factory xenons and no headlight washers, idiots in that country, headlights dont need washers its not a windshield, if they get a tad dirty wash the damn car 😂
I am moving tomorrow
You don’t need the headlight washers if they didn’t come from factory. You’re fine
May I know what did you spray on the reflector to clean it? I've dealt with lots of reflectors before and some aged reflectors couldn't even take a simple water wipes, it just comes off.
Best retro ever, just because the guy was in a blazer. Lol fantastic!
The cutoff is just amazing, gr8 work
Great video. Please make a video on how to remove clear shell/lense
Thanks! Check out our other video's in which we retrofit and remove headlight lenses :-)
Very nice retro, I noticed a bit of unfilled space with JB Weld between the projector and the back of the reflector, is that not going to make the projector somewhat rattles inside the housing given it is a heavy weight projector so the speak. Great job overall.
JB Weld is very strong and few spot is enough to hold it
Awesome job and thank you for sharing final outputs
Я чего то не допонимаю, или он 300 граммовую линзу на клей (холодную сварку) посадил? Она же на первой же кочке отвалится. Нужно крепить через шпильки в отражатель.
Не для росийских дорог
Желательно через отражатель стопсигналов
Как-то через жопу сделано, не надёжно! Вот если бы на жидкие гвозди, тогда да, а так нет!))))
Не сказал бы что она отвалится это же сварка захочещ не оторвещ поверь
За бугром распространённая тема так сажать
Tell me please. What substance you used to lock the lens in the reflector? And it is not dangerous to such a large lens mount only to the reflector? why you have not fixed on the bolts?
***** Would be very grateful if you would have posted a video on how to properly mount the lens screws.
***** I think many people would be grateful.
My Friend, I had a question? The slope point on the reference line is facing left. But you did it by turning the slope to the right. Can you please explain this? Thank you.
We are not sure what you mean. Please send us an email at info@retrofitlab.com
Thanks for the comeback my friend! In the video you taped the cutting line to the right on the wall. But the break, that is, the slope is to the left. After you attached the lens, the cutting line crossed to the left and the diffraction to the right. I could not understand this. Please explain, or was it not right-hand drive? Thanks
Wow, that's some hard ass reflector. We once tried to clean the reflector of a jetta mk4, and the damn thing got scratched all over. It was a bummer...
***** from this video I understand that it isn't necessary to take the alignment from 20 ft, a closer is fine ?
in your case it did turns good, right ? what distance was it ?
Thanks.
***** very good to know, but tell me is it enough to use only jb weld ?
***** Thanks.
Retrofitlab great video for the DYI.I am planning to buy the FX-R 3" projector and would need your advice on the Shroud.I dont want to trim a lot on the shroud. So your recommendation would be of great help. Was thinking of the Gatling Gun 2.0. Your thoughts please. What shroud was used in this video? Apollo?
hello sir, do u use all xenon kit (with ballast, trafo...) or just xenon lens and h7 bulb 6000k?
We used xenon projectors, xenon bulbs and 35w ballasts :)
so i finished retrofitting one side and after doing so, i get this weird greenish glow on my headlights. all i did was paint the shrouds and corner amber piece matte black and i doubt its because of that. is it the projector itself giving off this greenish tint on my lens?
u changed it from LHD to RHD? or maybe you wanted to do that?
Que producto es el que le aplica al cromo para limpiarlo?
We used glass cleaner, but best is to use a microfiber cloth without any cleaning products..
@@Retrofitlab excelente.
Gracias.
If my old headlight uses an H11 , and the new lens uses D3S HID bulbs lets say
i don't understand how will i power up the D3S news bulb with my OEM H11 connector ??? and what will i specially use for an HID system ??
Hi, I have a question, what product do you use to clean the chrome, I cleaned my headlight with water but the chrome part was damaged.
We use a regular "window cleaning". But actually the OEM chrome in some headlights is very fragile and comes off when you touch it with anything other than air :-)
i see there are gaps on top and bottom of the FX-Rs. even though they are small gaps, light can still be lost. would it be a good idea to seal the gaps completely or is there a reason for the gaps?
***** thank you!
FYI this is only possible if you headlight reflectors have a flat bottom. Most OEM lights sit at an angle and must be aligned on the car itself, which makes it much harder.
Even if it's at an angle, you still align it to the factory line on the wall at the angle the stock cutoff displayed. Once mounted it will be straight. Just match what it displayed.
Hi!Between FXR and Evo XR,which one is the best when it comes to the low beam?clarity,density of light and cutoff?
You just glued it into a plastic reflector, The projector had a metal mount that was also it’s heatsink. I wonder if this will melt?
I also wonder if it makes any sense to instal LHD projector into RHD car, you can notice that on the mirrored cutoff line 🙄
will it last for a year just months.
¿Dónde puedo comprar esas luces?
www.retrofitlab.com/en/xenon-projectors-1/aharon-fx-r-bi-xenon-projectors-30-1.html
I don't know if I can use 3" for fiat bravo II or I should use 2.5", I have already OEM projector...
That’s so awesome, well done 👍 ....subscribed
Thanks!
Regardless of ease of installation is the fxr really superior to the d2s 3.0 in terms of light output?
Can be used Honda insight 2009 car?
It seems this model with halogen headlights already has projectors. And in that case, these projectors probably won't fit. And we don't have info on which will fit, sorry.
does the jb stick and weld hold well? or does it need also the "nut and bolt"
+Retrofitlab how do you suggest on adjusting the roational alignment using nut & bolt before putting the jb weld?
do i just hold the projectors while it's on and mark the holes to be drilled?
What if i wanted to install projectors for my 10 years old Halogen projector lens ??
is there a video for that ?? ( installing a projector in place of an OEM projector )
That amazing
Thanks!
I'm for purchasing this projector in 2.5 inch is to place it in an opel corsa b do you think it is possible work by the size of the projector
now that bulbs do you recommend for the projector in xb morimoto 5500 k or a CbI osram?
if I mount instead MH1 instead goes there for sure because behind is smaller without customization ... but how I see fx-r is better MH1
Excelente, bien ahi
Thanks!
can i install an led bulb in the hid projector?
and if so do they light good?
nice work by the way.
would you recommend doing that?
also, what bulb sizes dose the MORIMOTO MINI D2S 4.0 take?
i cant find that piece of info.
many thanx
you have been of great help
Tienes algun lugar adonde poderte encargar un trabajo ??
Lo siento, no :)
Congret bro😃😃😃
Thanks
Perfect.
Thanks :-)
this bi-lens or mono? if bi, where is the control wire?
It was those red wires that were poking out
I m confused between Fxr 3.0 and d2s... Which one is better
FXR's use a D2S bulb.
I trying to understand where you connect always that red/black wire that appear at 3min:17. on the back of Xenon light. thx
These needs to be connected to the high beam splitters :)
very good film.
What the can of spray you used to clean the reflector?
It's a surface cleaner. But the chrome on the reflectors can react quite bad, so before you do this, test the cleaner on a small and/or not visible surface
Thank u for teaching!
You are welcome :)
Does JB Weld hold the projector very long time, if applied enough? Also durability with the heat?
Yes it will hold forever :) Once cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled and will withstand temperatures of up to 500 degrees F / 260 C.
fx-r 3.0 is fine for my opel corsa d ???
Привет . А что с углом на левой стороне был а теперь нет его ?
Про "Галочку" что-ли? Если про неё, то это же би-ксеноновая линза, у неё ровная линия.
Там все еще есть линия отсечки, но с этим биксеноновым проектором шаг не очень большой. Пожалуйста, дайте нам знать, когда у вас был другой вопрос.
how did you get that perfect line of light i got stock bixenon headlights on passat b6 but its not that distincitive.
Better headlight bulb itself, I also had that problem until I upgraded to HID
@@D1G1T4L1Z3D at the end it was burned out headlight lens inside no bulb could have make it better
Oh I see, yea new bulb won't help that lol
Is this plug and play for a car with H4 socket ?
+Retrofitlab i mean for the projector to fit , anything need to drilled or cutted ??
+Retrofitlab alright , thx for your time :3 gonna watch the video now :3
why u didn't hit the high beam ?
Ein Glück das es so etwas nicht Deutschland gibt ^,^
Not so sure about that... :)
It is possible uitilizar this projector in the C4 PALLAS lighthouse?
I saw that the quality is superior to Miromoto H1
Anxious hope your answer!
Hugs!
Romao Moita
***** ok, I will as soon as possible make the purchase of a pair H1 to my c4!
Thanks for the quick response!
Çok harika olmuş,,
Teşekkürler
Make a video for Jeep round 7" headlights or vw bettle/fusca/vocho please
is this the same bulb or changed?
No we used a D2S xenon bulb!
Nice wark
Thanks!
hi wich epoxy model u used
5:45 co to za środek do czyszczenia
How to install the hight beam and the led frame
The projector is bixenon. It has high beam
E o farol alto?
This projector is bi-xenon (low and high beam) :)
Hi will Gatling Gun 1.0 fit the FXR 3.0 ?
***** thank you guys saved me a lot of time. I really liked the Gatling Gun shroud so will go ahead n order that now.
Why did you install a LHD cutoff when the factory beams were RHD cutoff? Was the car imported to another country? This Is extremely dangerous if the cutoff is on the wrong side!
Mercek muayeden geciyormu
Good job!!!
Hey and the projector lens that size is???
***** thank you!
great job !!
now, i m using mini h1 on my 07 lancer
in next month i will exchange it to fxr projector .. :)
what brand is the projector sir? what will be it's cost?
Retrofitlab thank you sir
Круто
Perfect
Poteva mettere delle lampade led di xenonpertutti
Классно!!!!!!сделай пожалуйста на Chrysler Pacifica
Есть универсальные линзы. Закручивается гайкой. Смотри в ютубе. А это колхоз.
Why the fuck would you even go through all that serious. My brother you have a lot of patience.
Well done 🥇 but led's kit Is more powerfull
Thanks, this video is about 8 years old so there are better HID xenon and bi-led projectors now. Only some Bi-led projectors are more powerful and good HID projectors with quality bulbs are still very good.
👍
Thanks :-)
Денег на ксенон не хватило заводской?
Да, наверное, машина станет слишком дорогой или что-то в этом роде ....
в название ролика Bi, а вот проводов привода шторки не увидел
Partyzant eksperyment 😵😵😵
Credo che debba cambiare gli ammortizzatori...😂
Fabrizio T balla troppo 🤣
Nessuno scrive in italiano qui?
Qualcuno c'è
Линзы на клей🤔вы серьезно? Они отвалятся.
We used JB weld.. They won't fall off :)
@@Retrofitlab Usually these lenses are installed on the studs.
@@ДмитрийШумилов-н8ы Yes we know.. The nut and bolt method is much better to use, I agree with you!.. :)
Красиво,ну по-прежнему нихуя не видно 😁😁👍👍
Очень хорошо видно, сэр! :)
looked again and saw, sorry.
videos very fast
Lol ta mis un phare de droite a gauche ou inversement jsai pas si tu roule a gauche ou a droite.. Mais le phare est tout droit lol
Ovviamente sono anche illegali quindi non omologati per la strada, il fascio di luce acceca chi viene difronte e le bestemmie sono assicurate.
You will definitely not blind upcoming traffic, the light pattern is even better than original headlights! See the results: th-cam.com/video/YGaSY9P8Oko/w-d-xo.html
the reflector mirror is better painted black. Отражатель лучше покрасить в черный цвет.
Yes that does look better :)
А автокорректор где? Потом такие самоделкины и слепят всех.то ксенон то светодиоды напихают и думают что они молодцы.
Еще нужен омыватель. Или будет тряпкой вытирать ?
Нихуя они не слепят, если все правильно делать.
Не блатуй,автокорекот ему подавай, линзы под ксенон что ещё надо
@@красавчик-л3щ Им по правилам подавай) раз ксенон значит в линзу, а ещё автокорректор и омыватель...
Bad tutorial. Video is shown way too fast without any explanations.
If you need an explanation with this video I'd Suggest getting professional help with your lights.
What shroud did you use? And is it suppose to snap on to the projector?
Hi, we used the Apollo 3 in this video! Yes, the shroud is supposed to snap onto the projector.