Thank you SO MUCH for posting this!!!! I have the same exact car- same exact light to replace. You’re seriously my hero here… bc I definitely couldn’t have done this without this vid. You rock.🖤
I highly recommend you switch over to a set of H7 LED's they are SO much brighter and better looking than the old yellow halogen bulbs. Amazon has them for 30 bucks a set. I switched all 3 vehicles of mine over even foglights and couldn't be more happy!
This was a great video! Just a tip for the future, don’t touch the new bulb without gloves on. The oils from your skin will heat up on the bulb and burn it out much quicker
Thank you for posting this walkthrough video. After doing this I would recommend removing the front bumper. It only takes 5 minutes (1 screw each side and push pins in the front) and makes it WAY easier to get the headlight assembly in and out of the body. Thanks!
@@jaythegamblerr What could be easier than what he did. I don't think he needed to remove the air intake scoop. I'll check it again though. I have a 2016 Genny 3.8. I like the way he has the cold air intake setup.
You shouldn't scare people away from changing their own bulbs with a comment like this. You don't need to remove the front bumper; you don't even need to remove the air intake guide (that the uploader removed). Just the two bolts holding the headlights in, and a single Philips screw about 6" to the left of the hood latch. Then just pop the headlight right out (you need to use a little force) and replace the bulb. Super easy. Removing the bumper is ridiculous.
Mission accomplished! Much appreciated. I realized bending part of the front bumper made it much easier to detach and rest unit. Took me about 30-45 minutes to set up and replace both bulbs.
I can add extra tips as I have had to do this twice. Do everything in the video, they remove the three bolts holding the fender in place. Use a screwdriver plastic or rubber handle to hold the fender out some. You can do the same thing to the plastic and metal part on the front near the light assembly. Take a flathead screwdriver and get it under the plastic assembly at where the assembly bolts to the vehicle. Wiggle and GENTLY pry up on this screwdriver and if you are lucky it will quicly pop the assembly loose. The rest is easy,
For anyone who wants to try this: You don't need to remove the air intake guide that the uploader removed. Just the two bolts holding the headlights in, and a single Philips screw about 6" to the left of the hood latch. Then just pop the headlight right out (you need to use a little force) and replace the bulb. Super easy. Removing the bumper is ridiculous.
How long did your new bulbs last? I hear if it touches your skin, the oil from your skin or any dirt or oil from working on the car that was on your skin will burn out the bulb when it gets hot
Literally looked this up 5 minutes after finding out my same exact headlight burnt. Seems straight forward, what bulb do i need exactly? I googled it already im just making sure lmao
I bought some aftermarket headlights for my gen and the LED strip on only one of the lights is out 😭😒 need to find someone that’s knows about working on headlights
Well that was a first when I heard the Philips screwdriver being referred to as a "Cross Head" screwdriver. I've never heard one called that before. Ya learn something new everyday I guess.
![ประสบการณ์ จ้าง Developer ที่ผมจะไม่มีวันลืม [ภาค1]](http://i.ytimg.com/vi/bzivN4KDg-k/mqdefault.jpg)
You need to tell people they cant touch the bulb with their bare hands or it will ruin it. you have to wear jersey gloves or similiar.
Thank you SO MUCH for posting this!!!! I have the same exact car- same exact light to replace. You’re seriously my hero here… bc I definitely couldn’t have done this without this vid. You rock.🖤
Anytime friend
Appreciate the video. Straight and to the point for beginners like me!
I highly recommend you switch over to a set of H7 LED's they are SO much brighter and better looking than the old yellow halogen bulbs. Amazon has them for 30 bucks a set. I switched all 3 vehicles of mine over even foglights and couldn't be more happy!
Can you send the amazon link here
Always change the bulbs in pairs.
Right I was taught this as well if you change the one bulb you should change the other one too since the other one probs gonna burn out soon aswell
This was a great video! Just a tip for the future, don’t touch the new bulb without gloves on. The oils from your skin will heat up on the bulb and burn it out much quicker
Thank you for posting this walkthrough video. After doing this I would recommend removing the front bumper. It only takes 5 minutes (1 screw each side and push pins in the front) and makes it WAY easier to get the headlight assembly in and out of the body. Thanks!
No problem friend
@@jaythegamblerr What could be easier than what he did. I don't think he needed to remove the air intake scoop. I'll check it again though. I have a 2016 Genny 3.8. I like the way he has the cold air intake setup.
You shouldn't scare people away from changing their own bulbs with a comment like this. You don't need to remove the front bumper; you don't even need to remove the air intake guide (that the uploader removed). Just the two bolts holding the headlights in, and a single Philips screw about 6" to the left of the hood latch. Then just pop the headlight right out (you need to use a little force) and replace the bulb. Super easy. Removing the bumper is ridiculous.
I’ve got my Saturday morning coffee and about to replace both low beam bulbs. Let’s do this!
Mission accomplished! Much appreciated. I realized bending part of the front bumper made it much easier to detach and rest unit. Took me about 30-45 minutes to set up and replace both bulbs.
Thanks man this is a very appreciated straightforward video 👍🏻
My bulb literally just went out... thank you for posting this video really helps!!
Finally found what I was looking for. Thank you.
Thank You! Will be doing the same for the 1st time tomorrow.
Good luck !
Awesome job with step by step process
Love your 2 videos
Thanks bro lol
I can add extra tips as I have had to do this twice. Do everything in the video, they remove the three bolts holding the fender in place. Use a screwdriver plastic or rubber handle to hold the fender out some. You can do the same thing to the plastic and metal part on the front near the light assembly. Take a flathead screwdriver and get it under the plastic assembly at where the assembly bolts to the vehicle. Wiggle and GENTLY pry up on this screwdriver and if you are lucky it will quicly pop the assembly loose. The rest is easy,
Thanks for the diy vid👍🏽 your great💪🏽
For anyone who wants to try this: You don't need to remove the air intake guide that the uploader removed. Just the two bolts holding the headlights in, and a single Philips screw about 6" to the left of the hood latch. Then just pop the headlight right out (you need to use a little force) and replace the bulb. Super easy. Removing the bumper is ridiculous.
Dude I have absolutely no idea what Philips head screw you’re talking about. I’ve been struggling for over an hour and have made zero progress so far
@@dutchovenvidsu ever find it
@@dutchovenvids it's literally shown in the video.
I needed this. Thank ya!
Welcome !
THANKS FOR THE INFO.
Awesome video man! btw what type of bulb did you use? im thinking of getting an led one will it fit?
How long did your new bulbs last? I hear if it touches your skin, the oil from your skin or any dirt or oil from working on the car that was on your skin will burn out the bulb when it gets hot
Nice man came from ur bro I actually love cars and know a lot so this will be cool
Awesome so correct me if I’m ever wrong !
what year is your Genesis??
Thanks bro
Thanks for the help
Thank you! Nice 370 jaj
Sooo still remove the bumper to avoid that possible damage is what I’m seeing
Cool video man
Thank you :)
No thank u
Thanks man!
Good vid. Thanks super easy
Thanks💪💪💪
What kind of lights do you use?
forgot but car got totalled i drive a 370z now lol
Thanks bro!
Literally looked this up 5 minutes after finding out my same exact headlight burnt. Seems straight forward, what bulb do i need exactly? I googled it already im just making sure lmao
I don’t think a screw is supposed to be on that twist cover shit for the lights I didn’t have one on mine either. Dope video tho helped ya boi out
Welcome mate!
What cold air intake you got
From darkghoul subbed and like 👍🏽👍🏽👍🏽
I didn’t have a screw in that one thing u were talking about either
Please put your phone on a stationary tri pod , or have an assistant hold it . I was sea sick from all the head motion.
lol it was go pro attached to my head I think at the time haha sorry
I bought some aftermarket headlights for my gen and the LED strip on only one of the lights is out 😭😒 need to find someone that’s knows about working on headlights
Bro same here.
Be careful pulling it out or just take more of the car appart
Good Look
🔥👍🏼gg
Well that was a first when I heard the Philips screwdriver being referred to as a "Cross Head" screwdriver. I've never heard one called that before. Ya learn something new everyday I guess.
I unscrewed everything but for the life of me I can’t pull the headlight out
I think its bc you are a fine ass girl.....
and tbh, just pull it out hard af.
Make sure when you pull it the front bumper isn’t blocking it besides that just wiggle and pull as hard as you can lol
My bulb just went out smh 🤦🏻
Dark goul
Sure unscrewing stuff was easy buy pulling the headlight unit out is not. Do not recommend following this video
Plz give me a SHOUTOUT
??
ohh man you doing it wrong way take this video off lol your supposed to unloosened the 3 fender bolts and you rip it right out
try a stationary camera. lame
Don’t worry I got rid of the go pro