You don't need to pedal from a dead start if you learn to slip your clutch just right. Also, it would be best to hold the clutch when rolling your bike downhill. You might score the cylinder and piston.
1:19 lesson from this, ride like your invisible, because you basically are, and right of way means jack shit when it's 300 pounds vs 3,000 lb car always wins
I guess it probably varies from person to person but I found it fairly easy, if you have any trouble youtube has videos on everything! You could probably build a plane with a few help videos lol
I know what your going through dude make sure that black washer is in the throttle body head and is secure make sure that c clip is seated on the second last position near the end of the throttle pin where the spring is and the slide (this is what determines how much fuel is going into the engine lean or rich ) and make sure your choke nut is tighten and stays open . Adjust your throttle bolt so it like a sixteenth from the nut 🔩 then adjust your idle screw (found out this isn’t the air fuel mix mixture should be in half way or more
How many KM of range do you get on this bike? How much does it cost to fill up the tank fully of gas? And what’s the top speed of this bike? Also amazing video post more!!!
Back when this was made it was the stock exhaust, I just had it cut up and twisted so it would fit the frame of the bike! I actually miss riding this bike, its sitting motorless at the moment, I do have tons of videos of this bike and others on my channel if your interested, I upload once a week and my newer stuff is better. Thanks for watching!
Dumb question lol is that a license plate on the back is that bike insured and registered I say that was sarcasm just curious inquiring minds would like to know lol. I love the fact you are with the traffic.
Yeah I have that particular bike registered as a moped since I travel farther with it, not insured though, in ohio mopeds don't have to be, also I have to follow the same laws as regular traffic. Thanks for watching! Its a pretty old video I have much better and newer ones, I have no clue why this one gets all the attention lol 😂
@@twowheeledadventures don’t you need a vin to register how did you obtain that through the dmv did you have to apply for the vin sorry so many questions I’m new to this and am currently building two fat bikes just wonder what kind of Hula hoops I have to jump through
@@ferrelli76 I went into my dmv and told them what I had"Motorized bike", they handed me paper work to fill out, also I used the serial number on the bike, they all have them.
It's been awhile since I had a motor on this particular bike, but I remember it was an "80cc" motor and I was running a 44 tooth sprocket, "The sprocket is still on the bike lol" Pretty sure the top speed on this one was only about 30 mph. Thanks for watching, my newer videos are alot better quality in my opinion.
That's still pretty sweet I really don't want to go any faster in a pedal bike.I'm sure I could probably hit 45 with a smaller sprocket but I'm more for the torque but yea man u take urs in some long trips the longest I think I had one of mine going was abt hr and half with no shut offs
@@jerryb1234 since the person you asked hasn't answered, and in case you havent already figured it out in the last 7 months, what i believe they meant was, "this bike i am watching in this video is 50cc" and they hit enter to make a separate line, and said "this came to you from me, a person living in Bangladesh"
You build them, find a bike you like that will fit a motor, motors cost anywhere from 80-500 dollars, I build most of mine for 200, you can buy slap on kits like the phatmoto for 700ish though, look up motorized bike on amazon and that will get you in the right direction, or the bikeberry/gas bike websites
Depends on how steep, slight to medium inclines and they can mostly make it up unassisted, steep inclines and you'll have to help out the motor by peddling, you can also by a larger rear sprocket for the back like a 56 tooth to give you more low end power, most kits come stock with a 44 tooth, good news is you can peddle while the motor is running so even if you find a bad hill helping the motor by pedaling won't feel bad at all since the motor is still doing alot of the work, also most stocks kits go 20-30 mph with 25 being a good average!
@@twowheeledadventures Can you ride these without a driver's license? I have to wait a long time for my appointment to get my renewed driver's license because of the virus but in the meantime I like to have a way to get places in the town where I live.
@@notthatdigusted7468 It honestly kinda depends, sometimes you have to have them registered as a moped, you need need a drivers licence for that but not a motorcycle licence, I have 3 of these bike and have never been pulled over I pass lots of cops and most of them wave , 1 of them I have registered as a moped the other 2 I do not, I let my friend borrow one and he got pulled over, the cop asked him some questions and let him go, maybe call your local dmv or police office and ask them, it varies from place to place
Why did see one major problem with your whole set up you don't have a chain tensioner that's why your chain is so loose get on Google and look up chain tensioner if you haven't already figured that out by now I know this movies almost a couple years old now but that'll help you out your loose change problem other than that I love the bike as a sweet set up
I just want to say thank you for acknowledging that this video is old! I do indeed have chain tensioners now, 4 bikes also with a motorized trike coming soonish!
@@twowheeledadventures damn dude you staying busy I'm actually looking into going to school for small engine mechanic's to professionally work with Motors like these and similar Motors in boards in outboards which is the marine style how Motors that's what they call them for boats in crap which I'm not really looking to work on boats and any other things I wanna work on stuff like this on top of making a hobby these Motors are super easy to work on and their super simpledb upgrade its unbelievable and there's so much fun too ride and take places and go all sorts of places it's a lot of fun I just need to get a set up with a GoPro in a helmet and what not or something to record my ventures that I go on but for now I'm having fun watching everybody else
@@twowheeledadventures who knows maybe one day I'll be able to form a little club that be really cool especially since they don't have anything like that out here in Washington state southwest Washington to be exact
@@twowheeledadventures yeah I'm gonna have to wait a little while though because my current ride is down and out hi somebody gave me some bad gas and so I been trying to flush that out and trying to get it up and running and right when I was about to give up and running it somehow fell over at some point and broke the throttle cable right off where the engine cut off buttons app where it goes into the engine cut off button housing on the underside it broke that little plastic knob off where the metal screws in so I have to order a new one of those plus it rains a lot here so it won't probably be until like springtime by the time I actually get to do that because during the winter and fall it rains a lot out in the Pacific northwest but I will try to keep in touch hopefully don't forget
![[4K] TREASURE(트레저) “KING KONG” Band LIVE Concert 킹콩은 라이브를 찢어🦍 [it’s KPOP LIVE 잇츠라이브]](http://i.ytimg.com/vi/p8bLLOxPDD8/mqdefault.jpg)
You don't need to pedal from a dead start if you learn to slip your clutch just right. Also, it would be best to hold the clutch when rolling your bike downhill. You might score the cylinder and piston.
I love it when people run these engine hard without warming them up
1:19 lesson from this, ride like your invisible, because you basically are, and right of way means jack shit when it's 300 pounds vs 3,000 lb car always wins
i have a motorised bike and recently buckled the rear wheel. Is it relatively easy to get a new rear wheel on with the new gears etc?
I guess it probably varies from person to person but I found it fairly easy, if you have any trouble youtube has videos on everything! You could probably build a plane with a few help videos lol
good normal ride...
I know what your going through dude make sure that black washer is in the throttle body head and is secure make sure that c clip is seated on the second last position near the end of the throttle pin where the spring is and the slide (this is what determines how much fuel is going into the engine lean or rich ) and make sure your choke nut is tighten and stays open . Adjust your throttle bolt so it like a sixteenth from the nut 🔩 then adjust your idle screw (found out this isn’t the air fuel mix mixture should be in half way or more
get the velocity stack piece for your carb and add a ram air intake tube from you carb faceing the same way you drive make the engine run better
Kool video dude.
Thanks
You keep riding like you stole it your going to blow the motor
motivation... what day is it?
How many KM of range do you get on this bike? How much does it cost to fill up the tank fully of gas? And what’s the top speed of this bike? Also amazing video post more!!!
Look at my youtube channel, I have tons of videos! For the price of filling up its like a dollar lol, and id say 50ish miles
Amd thanks for watching!
Damn that was pretty dangerous there in the beginning. What exhaust do you have on this?
Back when this was made it was the stock exhaust, I just had it cut up and twisted so it would fit the frame of the bike! I actually miss riding this bike, its sitting motorless at the moment, I do have tons of videos of this bike and others on my channel if your interested, I upload once a week and my newer stuff is better.
Thanks for watching!
@@twowheeledadventures thanks for replying! I just subbed. Love your other content. Keep it up!
Dumb question lol is that a license plate on the back is that bike insured and registered I say that was sarcasm just curious inquiring minds would like to know lol. I love the fact you are with the traffic.
Yeah I have that particular bike registered as a moped since I travel farther with it, not insured though, in ohio mopeds don't have to be, also I have to follow the same laws as regular traffic.
Thanks for watching! Its a pretty old video I have much better and newer ones, I have no clue why this one gets all the attention lol 😂
@@twowheeledadventures don’t you need a vin to register how did you obtain that through the dmv did you have to apply for the vin sorry so many questions I’m new to this and am currently building two fat bikes just wonder what kind of Hula hoops I have to jump through
@@ferrelli76 I went into my dmv and told them what I had"Motorized bike", they handed me paper work to fill out, also I used the serial number on the bike, they all have them.
where can i buy high temperature red clutch friction pads
Do you still hold the clutch down once you got it started and when you slow down and stop
Yeah
Yes, 2 strokes will get very hot if you dont hold the clutch while slowing down because it sends less fuel to the cylinder which means less oil
Damn how many bikes you got bro? And honestly you like the 4 or the 2 stroke better?
I like them both but honestly like my 2 strokes better,
I have 4 motorized bikes and working on building a motorized trike!
I just built a 4 stroke rat bike but I'm going to start a second soon and I'll probably be go 2 stroke just so I can experience both
They are both honestly fun!
You look like your from Pennsylvania
you need to make your bike more lean by tuning the carb because your bike is 4 strokeing at high rpms
Again, old video.
Kinda sounds a lil funny like ur clutch plates not tight enough or something u can hear a metal on metal what u let off the gas and hit the clutch.
I'm feathering the hell outta it, but Im taking this motor "nextish" week and tearing it down to hopfully fix it.
Thanks for watching
How fast is it and is it a 50 cc or 80cc?
@@bryancarvey4619 66cc and about 28 mph
How far did you travel?
About 22 miles in total
How long does the gas last?
100ish miles a gallon, along time
How fast and is it a 50cc or 80cc?
He had to be going at least 40 mph with that Lil sprocket my "100" Cc anbull hits 40 with a 44 tooth
It's been awhile since I had a motor on this particular bike, but I remember it was an "80cc" motor and I was running a 44 tooth sprocket, "The sprocket is still on the bike lol"
Pretty sure the top speed on this one was only about 30 mph.
Thanks for watching, my newer videos are alot better quality in my opinion.
That's still pretty sweet I really don't want to go any faster in a pedal bike.I'm sure I could probably hit 45 with a smaller sprocket but I'm more for the torque but yea man u take urs in some long trips the longest I think I had one of mine going was abt hr and half with no shut offs
Things lil engine are pretty fun.I like em just as much my dirt bikes maybe a lil more Cuz we can take em anywhere with no cop issues
Contraption!!
Pretty much sums them up!
You climbed that hill like it was nothing. I'm surprised u didn't padel. That exhoust pipe is loud
I had a leak in the exhaust back then, thanks for watching!
Do you need a motorcycle licence for one of these?
No, but some states consider them a moped, but you only need a regular drivers licence for that
@@twowheeledadventures Ah, I see. Thank you.
@Jerry Brown Good to know
What's your sprocket size?
This bike is the stock 44 tooth
@@twowheeledadventures wow!
What’s Motor kit did you get man? Can I get a link? Also what’s your top speed on it
This is the kit I got for this particular bike but its no longer available
www.amazon.com/dp/B07KWYCKZ2/ref=cm_sw_r_apa_i_x5u0EbP233YKF
Look up motorized bike kit on amazon they have a few, gasbike is also a dencent place but they can get pricey
Top speed on this bike is 27-30
Austin Welsh thanks!
@@omegaperks190 , or bike berry .com
white linw...
Put some 2 cycle oil in it and it'll stop doing that
It has 2 cycle oil lol, if it didn't it would not have made the trip 😂
@@twowheeledadventures it didn't look like it did make the trip lol
I have a part 2, it makes it their and back lol
i have that same light..its 100% legit 👌🏼
I like it as well Im thinking of rigging something up to run off the motor tho! Thanks for watching!
What’s the light?
@@aldo9923
www.amazon.com/dp/B06XXKQ9RG/ref=cm_sw_r_apa_i_Ei7XEbX7JKFXP
This is 50cc bike
From Bangladesh
What is a 50cc bike From Bangladesh?
@@jerryb1234 since the person you asked hasn't answered, and in case you havent already figured it out in the last 7 months, what i believe they meant was, "this bike i am watching in this video is 50cc" and they hit enter to make a separate line, and said "this came to you from me, a person living in Bangladesh"
I would like to buy one of these how much are they?
You build them, find a bike you like that will fit a motor, motors cost anywhere from 80-500 dollars, I build most of mine for 200, you can buy slap on kits like the phatmoto for 700ish though, look up motorized bike on amazon and that will get you in the right direction, or the bikeberry/gas bike websites
@@twowheeledadventures How do these motorized bikes handle hills I live were there are a lot of hills?
Depends on how steep, slight to medium inclines and they can mostly make it up unassisted, steep inclines and you'll have to help out the motor by peddling, you can also by a larger rear sprocket for the back like a 56 tooth to give you more low end power, most kits come stock with a 44 tooth, good news is you can peddle while the motor is running so even if you find a bad hill helping the motor by pedaling won't feel bad at all since the motor is still doing alot of the work, also most stocks kits go 20-30 mph with 25 being a good average!
@@twowheeledadventures Can you ride these without a driver's license? I have to wait a long time for my appointment to get my renewed driver's license because of the virus but in the meantime I like to have a way to get places in the town where I live.
@@notthatdigusted7468 It honestly kinda depends, sometimes you have to have them registered as a moped, you need need a drivers licence for that but not a motorcycle licence, I have 3 of these bike and have never been pulled over I pass lots of cops and most of them wave , 1 of them I have registered as a moped the other 2 I do not, I let my friend borrow one and he got pulled over, the cop asked him some questions and let him go, maybe call your local dmv or police office and ask them, it varies from place to place
Hi
Hello!
Why did see one major problem with your whole set up you don't have a chain tensioner that's why your chain is so loose get on Google and look up chain tensioner if you haven't already figured that out by now I know this movies almost a couple years old now but that'll help you out your loose change problem other than that I love the bike as a sweet set up
I just want to say thank you for acknowledging that this video is old! I do indeed have chain tensioners now, 4 bikes also with a motorized trike coming soonish!
@@twowheeledadventures damn dude you staying busy I'm actually looking into going to school for small engine mechanic's to professionally work with Motors like these and similar Motors in boards in outboards which is the marine style how Motors that's what they call them for boats in crap which I'm not really looking to work on boats and any other things I wanna work on stuff like this on top of making a hobby these Motors are super easy to work on and their super simpledb upgrade its unbelievable and there's so much fun too ride and take places and go all sorts of places it's a lot of fun I just need to get a set up with a GoPro in a helmet and what not or something to record my ventures that I go on but for now I'm having fun watching everybody else
@@derekloney5821 If you end up recording your furture rides comment on a video and let me know, I always love seeing others builds!
@@twowheeledadventures who knows maybe one day I'll be able to form a little club that be really cool especially since they don't have anything like that out here in Washington state southwest Washington to be exact
@@twowheeledadventures yeah I'm gonna have to wait a little while though because my current ride is down and out hi somebody gave me some bad gas and so I been trying to flush that out and trying to get it up and running and right when I was about to give up and running it somehow fell over at some point and broke the throttle cable right off where the engine cut off buttons app where it goes into the engine cut off button housing on the underside it broke that little plastic knob off where the metal screws in so I have to order a new one of those plus it rains a lot here so it won't probably be until like springtime by the time I actually get to do that because during the winter and fall it rains a lot out in the Pacific northwest but I will try to keep in touch hopefully don't forget
Its i 2 stroke
Yes
Your running your carb to rich drop your needle a notch should clear up your acceleration
Thanks for the advice! But this motor is in my basement now lol. Still runs just replaced it.
That sounds faster mine
It toped out at about 27 mph, old video though lol.
I have much newer stuff on my channel.
That van was already pulling out, you was in the wrong.
You realize the van has a stop sign and that I do not, therefore I have the right away.