Replace brake lever arm without dismantling from handlebar or bleed. To access rubber cap & axle fixing bolt easier it is good to release lever reach at first.
@@kamilhultaj5006 IT'S FUCKING BALL ACHE TRUST ME - ONE OF THE WORST FUCKING THINGS IVE EVER HAD TO DO, BUT IT'S DOABLE GET SOMETHING LIKE A LONG ALLEN KEY AND POKE IT THROUGH THE HOLE WHILST HOLDING THE SPRING IN PLACE U THEN WANT TO WIGGLE THE LEVER UP AND DOWN LIKE FUCK AS U JAM IT THROUGH GOOD LUCK, LET ME KNOW HOW IT GOES
Hi metod, In my case I couldn’t remove the axle. I saw in your video that you removed them easily but my axel is so tight that I can’t move it. Some tip to remove it? It’s normal that I haven’t been able to move it? Regards and thanks for your video.
It is not easy for the first time. Try to put hex nut around the rod on topside parallel to surface so you can see the rod thru nut hole. Add short rod from bottom side and try to squeeze this "sandwich" with pliers. Don't forget to trotect surfaces against scratches with self adhesive tape or cloth. Hope you will manage it.
Yes, sometimes it needs a quite strong push to release the axle for the first time. Try to use a short plastic plastic ring and put it around the axle on bottom side. On the top side add a short plastic axle above the brake lever axle and squeez al this sandwich with a pliers for a few millimeters. I advise using plastic materials to avoid unwanted scratches on the brake levers.
The title should say "brake lever *blade* replacement". "Brake lever" is the whole thing you mount on the handlebar. (sorry, looking for a brake lever replacement video :-D)
Actually, the title is 100% accurate and correct. 😱A _brake_ LEVER is exactly that, the LEVER which is used to operate the brake mechanism. 🤯Why, you ask, is it NOT referred to as a blade? 🤔Because blades are used for cutting, they’re found in razors and knives, etc but definitely nowhere to be found in any brake mechanism. 😳 Just for your benefit, the entire assembly is known as the brake lever mechanism or assembly, not just a brake lever because a lever is a specific thing, and levering is what it does and all it does. 😒There is nothing whatsoever that’s in any way blade-like. Not sure what kind of blades you’ve come across but everyone I’ve ever seen had a very narrow and very sharp edge running down the length of it. 🤨Again, this brake LEVER has none of that. Hence, it’s in no way a blade and shouldn’t be referred to as such.🤓
Short, shows everything and I dont even need sound on. Amazing, thanks for sharing.
:) Glad to help.
More detail in how the spring is added would have nice…on to the next video😂
Wish u would have show how the spring goes in..
I FKING CANT PUT IT BACK JESUS CHRIST.....
@@kamilhultaj5006 IT'S FUCKING BALL ACHE TRUST ME - ONE OF THE WORST FUCKING THINGS IVE EVER HAD TO DO, BUT IT'S DOABLE
GET SOMETHING LIKE A LONG ALLEN KEY AND POKE IT THROUGH THE HOLE WHILST HOLDING THE SPRING IN PLACE
U THEN WANT TO WIGGLE THE LEVER UP AND DOWN LIKE FUCK AS U JAM IT THROUGH
GOOD LUCK, LET ME KNOW HOW IT GOES
Great! Nice and concise! Thanks for adding the part number shots!
Thanks for the help dude. I was in a bind and this did the trick!
The 1st one i saw, removed the caliper itself. Good thing i saw this. And its very easy
Awesome! Thanks
Very helpful, thank you.
You're welcome.
Great video, thanks
You're welcome.
Thanks dude 😎!
Glad to help.
Hi metod,
In my case I couldn’t remove the axle. I saw in your video that you removed them easily but my axel is so tight that I can’t move it. Some tip to remove it? It’s normal that I haven’t been able to move it?
Regards and thanks for your video.
It is not easy for the first time. Try to put hex nut around the rod on topside parallel to surface so you can see the rod thru nut hole. Add short rod from bottom side and try to squeeze this "sandwich" with pliers. Don't forget to trotect surfaces against scratches with self adhesive tape or cloth. Hope you will manage it.
Same issue with mine. That axle seemed seized in there. I had to order a new lever assembly for $44.
Boom! And just like that
Thanks a lot.
You're welcome.
Dimana jual breake lever nya om
The pin doesnt want to come off...
👍
What can I do if the lever axel doesn’t move?
Yes, sometimes it needs a quite strong push to release the axle for the first time.
Try to use a short plastic plastic ring and put it around the axle on bottom side. On the top side add a short plastic axle above the brake lever axle and squeez al this sandwich with a pliers for a few millimeters. I advise using plastic materials to avoid unwanted scratches on the brake levers.
Where can I buy SL-M6100 LEVER at? Pls Lmk
www.xxcycle.com. But I see now that it is not available at the moment.
The title should say "brake lever *blade* replacement". "Brake lever" is the whole thing you mount on the handlebar. (sorry, looking for a brake lever replacement video :-D)
Actually, the title is 100% accurate and correct. 😱A _brake_ LEVER is exactly that, the LEVER which is used to operate the brake mechanism. 🤯Why, you ask, is it NOT referred to as a blade? 🤔Because blades are used for cutting, they’re found in razors and knives, etc but definitely nowhere to be found in any brake mechanism. 😳
Just for your benefit, the entire assembly is known as the brake lever mechanism or assembly, not just a brake lever because a lever is a specific thing, and levering is what it does and all it does. 😒There is nothing whatsoever that’s in any way blade-like. Not sure what kind of blades you’ve come across but everyone I’ve ever seen had a very narrow and very sharp edge running down the length of it. 🤨Again, this brake LEVER has none of that. Hence, it’s in no way a blade and shouldn’t be referred to as such.🤓