Finally the video I was looking for! Given how quickly this material breaks down in the summer heat, I'm surprised it took me hours to find a how to on this 😂 Thanks!
@SleepyCrane-xx5cw I'll be replacing them out soon. Had a worse issue arise. I didn't seal the hole that runs the hood release cable while running my 0 gauge wire to the back of the ride to run an optima rear battery with battery isolator as well as other accessories and volt meters for last years car show. And because I installed waterproof leather inserts that covered up the floor I didn't realize all the water coming in through that hole.. 😬 yeah. New comfort control module installed and I am working on replacing the door lock actuator and checking all the relays. Not fun. Due to be replaced anyways but still. Was my bad.
Great video! Thank you! Is there any technique for reattaching interior vinyl to the door panel without removing the vinyl piece? Would injecting a small amount of adhesive through the vinyl, then applying pressure, be a workable option?
This looks amazing. If you broke the tabs off to add the upholstery, how did you get the panel back on? Was there enough plastic to poke through the panel and melt back into place?
I'm doing this on B5.5 Passat and glue is absolute PITA to remove. I've tried nitro thinner, I've triex Sonax glue remover, in the end i have to use a knife and scratch off everything...
Great video....Did I miss it or did you not show the most important part which is how to anchor it to the door again..... Thank you for showing video is helpful
Paul Iascau's studio Yup,am sa incerc...mai demult am schimbat plafonul la un Opel Astra H Caravan,cu vinilin si banalul prenadez si mi-a iesit bine...acum am sa incerc cu ce mi-ai recomandat tu. Multumesc !
Hi! I just found your video, 3 years later as you made it! :-) What is that blue handheld tool what you are using to remove the inside part of the door panel? Regards
Hi. The only thing i can not see on the video is taht any foam under the fabric? I'm planning to do it on my car but all the fabrics i was looking comes with foam on it and i don't know if the door panel needs any or is it just simply the fabric glued on without any foam under it? Thanks if you take the time to answer this question for me.
Sauce Alex I did not have to remove the factory glue brcause the original material had come off the panel alone... But Tessa has a special spray to remove the glue
I've been trying to do my doors and I have a mk4 gti and the fabric I got kept bunching up so I need to get different fabric any recommendations and how to keek it from bunching up around the curves?
I melt the excss from the plastic tabs from the outside in and I was left with big tabs, so after I finished I put the upholster panel back and I used the soldering iron to melt the tabs to reattach it. And to reattach the panel to the door I tink it has some plastic pins and some clamps
Thank you for your reaction. However, your panel looks like to be made of a different material than mine. Mine is a wood/paper like structure and yours look like there a kind of ABS plastic.
Salut.De unde as putea sa cumpar si eu material pentru fetele de usi mai elastic ? Am luat unul si nu se intinde mai deloc si acum caut altceva dar se gaseste cam greu
Wie hat er den Kunststoff so sauber vom Kleber befreit?!?! Kann mir einer sagen wie ich den Kleber ab bekomme? Hab schon 24 verschiedene Chemikalien versucht, Folienradierer, Schleifer, Drahtaufsätze.....
@@pauliascau danke für die Antwort. Das hatte ich auch versucht aber das verschmierte irgendwie nur. Letztendlich hab ich alles mit nem Spachtel mühevoll abgeschabt
J G sounds easy enough. Watched another video in which the guy used Xylene!!!! But Goo-Gone sounds much better and easier. Thanks! Also, how did you reattach the reupholstered piece to the main panel?
@@SteveFloresCoach I haven't yet. The material I picked out is too thick and I'll have to get thinner material that stretches so it will go on smooth. I plan to use "3M Headliner and Fabric Adhesive" from Amazon.
![[Watch Party] APL 2024 ใครชนะเข้ารอบ Hydra 🆚 Flash Wolves Talon 🆚 GGLive](http://i.ytimg.com/vi/BvuSgyLy4hA/mqdefault.jpg)
Finally the video I was looking for! Given how quickly this material breaks down in the summer heat, I'm surprised it took me hours to find a how to on this 😂 Thanks!
You're welcome :)
Paul Iascau's studio what type of fabric did you use? I’m have a hell of a time with this faux leather
@@JesusEffingChrist upholstery fabric some kind of velvet
Really good job!!!one of best diy vids for this. Thank you
I have been looking for this for a long time! I am planning to diy my door panel with a heavy furniture fabric. I hope it works
My 04 Passat 1.8T 5-Speed GLS has tucking issues as well on the driverside upholstery. Thanks for the upload.
Thnks for watching! :D
03 Passat with same issue
@SleepyCrane-xx5cw I'll be replacing them out soon. Had a worse issue arise. I didn't seal the hole that runs the hood release cable while running my 0 gauge wire to the back of the ride to run an optima rear battery with battery isolator as well as other accessories and volt meters for last years car show. And because I installed waterproof leather inserts that covered up the floor I didn't realize all the water coming in through that hole.. 😬 yeah. New comfort control module installed and I am working on replacing the door lock actuator and checking all the relays. Not fun. Due to be replaced anyways but still. Was my bad.
Great video! Thank you! Is there any technique for reattaching interior vinyl to the door panel without removing the vinyl piece? Would injecting a small amount of adhesive through the vinyl, then applying pressure, be a workable option?
This came out amazing. I am going to try it myself. What did you use for the carbon fiber look on the door handles and the center panel?
Thank you! A cousin who has a car vinyl wrapping company used carbon fiber vinyl to wrap them in vinyl
I've been to every upholstery shop in town and noone will touch my 08 jetta door panel.
Same
Wow, excellent job, I need to get this done on my MK5 Jetta!
Thank you!
Exactly the same, My MK5 Jetta front two door fabrics are terrible and falling off!
@@rynwolfeh1904 I got my own sorted. It's like brand new again! 😊
Ohm its soo cool vid. I`m doing it to my wv and i searched somth like that like few months how to do it. It is wery helpfull. Great vid tnx
Is it hard to streach it the curves?
Very nicely executed! Good job!
Thank you!
Thanks for the incite!
Beautiful. I need to do this
Thank you!
This looks amazing. If you broke the tabs off to add the upholstery, how did you get the panel back on? Was there enough plastic to poke through the panel and melt back into place?
I didnt' broke the tabs, I melt the excss off from the outside in and I was left with big tabs, so I had enough material to melt
I'm doing this on B5.5 Passat and glue is absolute PITA to remove. I've tried nitro thinner, I've triex Sonax glue remover, in the end i have to use a knife and scratch off everything...
Is it a specific kind of fabric that goes on there or can you just use any fabric
Danke für das Video:))
How did you secure the upholstered bit back to the door card?
I used a soldering iron to melt the plastic bits from the back
How did you attach the insert back to the door panel since you broke off the tabs?
I left enough of the tabs so I can melt them in place
Salut, cu ce unealtă ai desprins bucata cu material de fata de ușă? Pare sa fie un cuter in video, multumesc
In the end you found a use for the geometry kit 😂 Still, nice video, even if you didn't use foam between...
Thanks! I tried using foam but I dont have the right matrials, fabric and it was still coming off, so I use simply the fabric
Thanks to share your work like my work i salute
How do you re attach the fabric part to the door panel when you cut the tabs off?
Great video....Did I miss it or did you not show the most important part which is how to anchor it to the door again..... Thank you for showing video is helpful
I kept the small plastic tabs and then melt them on the panel to fix it to the bigger panel
The panel was fixed to the door with the plastic clamps or tabs and bolts
@@pauliascau ok thanks
Buna treaba...urmeaza aceeasi operatiune si la a mea,sper sa-mi iasa la fel :)
Bravo,felicitari !
Gheorghe Edwardt Multumesc! Din experiența mea, iti recomand sa folosesti spay tessa pt tapiterii auto ... e foarte bun si merge repede :)
Paul Iascau's studio Yup,am sa incerc...mai demult am schimbat plafonul la un Opel Astra H Caravan,cu vinilin si banalul prenadez si mi-a iesit bine...acum am sa incerc cu ce mi-ai recomandat tu.
Multumesc !
Gheorghe Edwardt. Cu placere! eu am lipit vinil pe un panou de usa de Sprinter, cu prenandez si mi-a iesit patat
did you just hot glue stick the panel back into the door panel...thanks
sorry for the delay, the panel has pastic tabs on the back, I melt them after I put the panel back in the bigger panel
Im about to do this myself, what did you use to re bond the plastic to the door card?
I used soldering iron
Hi! I just found your video, 3 years later as you made it! :-) What is that blue handheld tool what you are using to remove the inside part of the door panel?
Regards
My glove it's blue, I used a wood chisel
What kind of fabric did you use?
looks easy but it's pain in the ace. Can't get it right🤣
how time need for taking the panel at door
Hi. How did you clean the sticky glue?
Hi. The only thing i can not see on the video is taht any foam under the fabric? I'm planning to do it on my car but all the fabrics i was looking comes with foam on it and i don't know if the door panel needs any or is it just simply the fabric glued on without any foam under it?
Thanks if you take the time to answer this question for me.
Hi! Sorry I couldn't answer sooner, I glued the material directly without foam. The car comes from the factory with foam.
Damn you couldn't speed it up a little, I almost saw something that I could use!!!
How did you remove this old glue of the old door trim?
with nitrocellulose reducer
what materials and products did you use to remove the factory glue?
Sauce Alex I did not have to remove the factory glue brcause the original material had come off the panel alone... But Tessa has a special spray to remove the glue
I've been trying to do my doors and I have a mk4 gti and the fabric I got kept bunching up so I need to get different fabric any recommendations and how to keek it from bunching up around the curves?
You have to try to stretch as much as you can... I had some wrinkles in the fabric, but I tried again and it works
And also try to glue it little by little so that way you have more control
what glue is that? the one you used.... I could use it with fabric right? (:
Its specially made for automotive upholstery by Tessa
Interesant!
Am încercat și eu ,pentru prima data ,dar a ieșit vit de cit ,..dar se mai vad pe alocuri urme de degete ..???
The beast video
Thank you! :)
very good nice
Thank you!
how did you reattach the side panel to the door?
I melt the excss from the plastic tabs from the outside in and I was left with big tabs, so after I finished I put the upholster panel back and I used the soldering iron to melt the tabs to reattach it. And to reattach the panel to the door I tink it has some plastic pins and some clamps
Can I use any material? Did you just glue the door card back in to the door panel?
You should use quality materials. the door card has some plastic clips that I melted on the back of the door pannel with the soldering iron.
Awesome. Thank you!
You're welcome! :)
I need to do my mk5 gli
Did you get it done? I gotta do the same thing on my MK5 GTI
How did you remove the old glue between the panel and the fabric?
I used paint thinner, spatula and a rag
Thank you
for your reaction. However, your panel looks like to be made of a different material than mine. Mine is a wood/paper like structure and yours look like there a kind of ABS plastic.
How did you break the tabs off? What is that tool?
with a wood chisel
Homa que tela se usa para hacer 1 trabajo asi
What kind/brand of material did you reupholster with?
I went to the maeket and bought some generic faric for automotive upholstery ... I think it's made here in Romania
You can use headliner material, it's foam backed fabric. Found it sold by the yard on Amazon.
Ce material ai folosit?
What music is that? It's pretty cool.
Tremsz by Gunnar Olsen
did you use back staples or just glue
just glue
what tool was that to remove the insert
To remove the panel I used a screwdriver and to remove the insert I nused a solfering iron
genial, what kind of cloth is that?,
I think it's plush fabric
How did you get the old glue adhesive off
With paint thinner and a spatula
How you do take it out with what tool
I was cutting the tabs with a chisel
salut, poti sami spui si mie cum ai prins din nou panelul mic cu panelel mare?
Am folosit un ciocan de lipit pt instalatii electrice, dupa ce am montat panoul micut pe cel mare an topit urechiusele pe dos
ok,mersi mult
Unstoppable Cu placere!
Salut,sprayul folosit este rezistent si la caldura?cat timp a tinut lipit?
salut, sprayul e special pt tapiterii auto, insa acuma dupa aproape 2 ani incepe sa se desprinda unde era materialul sub tensiune
Paul Iascau's studio ok,multumesc
Welcher Stoff ist das genau? Bei mir im alcantara sind falten drin wo ich nicht rausbekommen mit 3mm stoff
Es ist eine Art Samt, ich habe es vom Markt gekauft
What spray is it?? You barely showed it!
Tessa glue for automotive upholstery
Salut.De unde as putea sa cumpar si eu material pentru fetele de usi mai elastic ? Am luat unul si nu se intinde mai deloc si acum caut altceva dar se gaseste cam greu
sincer sa fiu asta l-am cumparat din piata de la un magazin de materiale, nici acesta nu era elastic, l-am fortat destul de tare ca sa stea
Asa am facut si eu am dat 60 lei pe un metru jumate,dar mi-au iesit ok doar pe spate iar pe fata cat de cat
What glue do you use?
Tessa upolstery spray glue
Wie hat er den Kunststoff so sauber vom Kleber befreit?!?! Kann mir einer sagen wie ich den Kleber ab bekomme? Hab schon 24 verschiedene Chemikalien versucht, Folienradierer, Schleifer, Drahtaufsätze.....
Ich habe Nitroverdünner verwendet
@@pauliascau danke für die Antwort. Das hatte ich auch versucht aber das verschmierte irgendwie nur. Letztendlich hab ich alles mit nem Spachtel mühevoll abgeschabt
which kind of spray did you use
Tessa automotive glue
+Paul Iascau's studio thank you
You're welcome
salut, esti din Bucuresti? imi poti face si mie la un golf 4 la usile din fata?
din pacate sunt din cluj-napoca, dar sar putea face insa nu stiu cat va costa cu tot cu transport si daca ti se merita
How did you remove the old glue?
I just pulled my door fabric off today. I used Goo Gone spray, a scraper and a rag to remove the glue. It worked very well.
J G sounds easy enough. Watched another video in which the guy used Xylene!!!! But Goo-Gone sounds much better and easier. Thanks!
Also, how did you reattach the reupholstered piece to the main panel?
@@SteveFloresCoach I haven't yet. The material I picked out is too thick and I'll have to get thinner material that stretches so it will go on smooth. I plan to use "3M Headliner and Fabric Adhesive" from Amazon.
Oh, I'm not separating the pieces. I'm doing it with the door in place.
J G oh I see. You think it’ll stretch well into the edges?
Shop location nyo pls ?
What music is 3:36-4:25???
I don't really know, but I took it from youtube library
I have a problem of removing my door panels of Nissan windroad y11 1999 .
I'm sorry, I don't have experience with that model
Ce mașină este?
passat B5
1 summer month solution…
Next time leave out the music and actually speak and give a run down on what you are doing. Would be far more useful than annoying music.
too much comic/ mickey mouse........... // nothing explained // not good for unexperienced hobby mechanics
what did you use to glue the upholstery panel back on the door panel?