Gyro settings were really helpful, I thought my drone was broken and was looking for new mainboard. Now everything is perfect, even better than when it was new from the box. Thank you !
Don't forget the compass calibration for direction. It's in the instructions. Spread sticks out to the bottom instead of in. Then compass heading is set.
Hi, maybe someone can help me out. Got one of this lil' drones and my kid just set it tokinda revers mode. When you push the right rod to fly to the front it flys back, sam with left right. Does everything mirrored. How can it be fixed? Thanks!
I can tell you how I did the stick extension mod. The stock stick pops off the gimbal, carefully twist it off. I found a piece of wood dowel the appropriate diameter for the extension. Cut the dowel to length for the extension, then drill it to fit over the nub that is protruding from the gimbal. Drill a hole on top of the dowel for the thumb rest. Once you have the length you want apply a little hot glue and you are good to go.
abghere to make these is easy. I used wire insulation of two sizes. The main shaft of it is a thicker gauge wire like 6 or 8 gauge and then the inner one is like a 16 gauge wire stripping need to slide a little piece in the end just so you can put your grip on the top and Slide the other one down on the remote. I hope that makes sense.
Bucket List Guys i have settled the gyro by pushing to 45 degree also it runs fast .it is not stable standing it keeps on moving in one direction and also not stands in proper height little rise goes above 19 metres and little down arrow falls down please make a tutorial to drive it. Plz reply Help
NITHIN KUMAR make sure the quad is on a flat surface when you're setting a gyro and take off the top and make sure the screws are tight holding the circuit board down. When I got mine my screws were loose from brand new.
Need your help with my newly bought E010s. Did your "scorpion -tail mod. PROBLEM: When I plug a freshly charged battery in my e010, I get no light and the Motherboard heats up. BUT when plugging in a freshly charged 180mAh 3.79m 25c(long skinny battery, it immediately powers on(no lights) motors spinning super fast...Any suggestions other than throwing it away? Thanks.
Dave Silva most likely you have the leads put in backwards change your positive and negative leads on that scorpion tail you might have the power leads backwards.
Bucket List Guys- red is soldered on red/black is soldered on black. It was flying fine for 3 flights after I made the "tail" I have a few of the smaller rectangle batteries from another quad that have a smaller connector which is why I added the tail. It flew fine with those. It started when I tried the long- skinny battery when the problem started. Again that battery made the quads props spins super fast without even binding . Now when I attach the smaller batteries to the quad only the red light slightly dims on and mother board heats up. I'm stumped since I see a lot of people on TH-cam flying these E010s with both batteries...
Dude is there a way I can remove my damn lipo battery from my furibee h180 wifi drone without breaking my damn circuit board, ripping my motor wires which are bending under the frame the way they are setup out of the box ?????... I just got this drone earlier today and my hands are too big. My fingers aren't the thickest but I have big fingers and trying to grip the tip of my connector to pull it out from the drones connector is too damn hard !!!!!!!. I'm afraid I'm going to snap my drones blade guard frame which is still stock and it had brushed motors. The little 260 mah lipo is stock it came with it and runtime really sucks lol. Only two-four good minutes and it's dead !!!!!. Takes 40 minutes just to charge it !!!!. I had to grip it with the wires of the lipo to pull it out man I don't have a tool to remove them besides knives in the kitchen. I just bought it and don't want to mess anything up man. Any suggestions, tips..... Also if I'm bugging on the wires and the lipo still feels solidly connected. With the connector head does it mean that I haven't done any damage to the battery wires and connector head...??? I pulled it out by grabbing the wires on the first two runs..... I'm afraid that I might've already damaged the battery by doing that. It's still charging normal and is intact. Anyways please give me your feedback I'm extremely nervous and pissed that I just got this 40 dollar fpv indoor racing drone man. Furibee h180
Gyro settings were really helpful, I thought my drone was broken and was looking for new mainboard. Now everything is perfect, even better than when it was new from the box. Thank you !
mantolis33 definitely, that is awesome to hear your drone is fixed.
That gyro thing is exactly what I was looking for. thanks
Don't forget the compass calibration for direction. It's in the instructions. Spread sticks out to the bottom instead of in. Then compass heading is set.
Hi, maybe someone can help me out. Got one of this lil' drones and my kid just set it tokinda revers mode. When you push the right rod to fly to the front it flys back, sam with left right. Does everything mirrored. How can it be fixed? Thanks!
Thanks! Great tips.
I see you have the remote stick extended, can you show how?
I will do a video tomorrow for that.
I can tell you how I did the stick extension mod. The stock stick pops off the gimbal, carefully twist it off. I found a piece of wood dowel the appropriate diameter for the extension. Cut the dowel to length for the extension, then drill it to fit over the nub that is protruding from the gimbal. Drill a hole on top of the dowel for the thumb rest. Once you have the length you want apply a little hot glue and you are good to go.
You can use gourmet lollipop sticks too. I have them in my video, but you can google Chuppa lollipops.
abghere to make these is easy. I used wire insulation of two sizes. The main shaft of it is a thicker gauge wire like 6 or 8 gauge and then the inner one is like a 16 gauge wire stripping need to slide a little piece in the end just so you can put your grip on the top and Slide the other one down on the remote. I hope that makes sense.
thanks man, cool ! 👍
It's moving fast in one direction help me
NITHIN KUMAR did you set the gyro?
Bucket List Guys i have settled the gyro by pushing to 45 degree also it runs fast .it is not stable standing it keeps on moving in one direction and also not stands in proper height little rise goes above 19 metres and little down arrow falls down please make a tutorial to drive it.
Plz reply
Help
NITHIN KUMAR make sure the quad is on a flat surface when you're setting a gyro and take off the top and make sure the screws are tight holding the circuit board down. When I got mine my screws were loose from brand new.
How do i calibrate using taransis x9d se I don't have stock remote
Need your help with my newly bought E010s. Did your "scorpion -tail mod. PROBLEM: When I plug a freshly charged battery in my e010, I get no light and the Motherboard heats up. BUT when plugging in a freshly charged 180mAh 3.79m 25c(long skinny battery, it immediately powers on(no lights) motors spinning super fast...Any suggestions other than throwing it away? Thanks.
Dave Silva most likely you have the leads put in backwards change your positive and negative leads on that scorpion tail you might have the power leads backwards.
Bucket List Guys- red is soldered on red/black is soldered on black. It was flying fine for 3 flights after I made the "tail" I have a few of the smaller rectangle batteries from another quad that have a smaller connector which is why I added the tail. It flew fine with those. It started when I tried the long- skinny battery when the problem started. Again that battery made the quads props spins super fast without even binding . Now when I attach the smaller batteries to the quad only the red light slightly dims on and mother board heats up. I'm stumped since I see a lot of people on TH-cam flying these E010s with both batteries...
Dave Silva you may have wired it backwards.
I cannot have a stable drive
Dude is there a way I can remove my damn lipo battery from my furibee h180 wifi drone without breaking my damn circuit board, ripping my motor wires which are bending under the frame the way they are setup out of the box ?????... I just got this drone earlier today and my hands are too big. My fingers aren't the thickest but I have big fingers and trying to grip the tip of my connector to pull it out from the drones connector is too damn hard !!!!!!!. I'm afraid I'm going to snap my drones blade guard frame which is still stock and it had brushed motors. The little 260 mah lipo is stock it came with it and runtime really sucks lol. Only two-four good minutes and it's dead !!!!!. Takes 40 minutes just to charge it !!!!. I had to grip it with the wires of the lipo to pull it out man I don't have a tool to remove them besides knives in the kitchen. I just bought it and don't want to mess anything up man. Any suggestions, tips..... Also if I'm bugging on the wires and the lipo still feels solidly connected. With the connector head does it mean that I haven't done any damage to the battery wires and connector head...??? I pulled it out by grabbing the wires on the first two runs..... I'm afraid that I might've already damaged the battery by doing that. It's still charging normal and is intact. Anyways please give me your feedback I'm extremely nervous and pissed that I just got this 40 dollar fpv indoor racing drone man. Furibee h180