A huge tip for putting in the relay. You do not need to get on your back underneath the dash in order to plug it in. Simply reach around the left side of the fuse panel and plug it in by feel. The relay is plugged in with the vertical terminals on the bottom and the horizontal terminals at the top. Feel for the first 2 relays (they are located on the back left one on top of another vertically) and the fog light relay goes right below those 2. It is on the left side of the fuse panel when looking at the panel from the dash. Hope this helps. Took me 2 minutes to figure it out hope you can find it even faster with these tips. Again, reach around from the left side of the fuse panel feel for the third relay location, and plug it in.
This was a excellent tutorial, now I know that the 1st gen Scion Xb's come prewired for fog lights...this shows you how to make use of this option if your XB isn't fully equipped with fogs.👍🏽🇺🇸🇯🇲🌴☀️🌴
Notes on relay installation: I had to lay on my back with a mirror and light to find the relay socket and determine orientation. Once that was determined, I sat in the driver's seat and positioned the relay from the side of the fuse box. Pretty frustrating, but no way I was getting that thing in from underneath. Once I figured out how to get it in there, I was done in a few minutes. Thanks for the video. I would have been clueless how to get this done without it!
this is a great video, great instructions, about the headers, for couple decades ive been replacing and modifing. all i meant was that high quality is best way to go because there is a lot of r&d. thats all
Yooo I installed my fog lights today! Started with the hardest part - the relay. What a pain in the back! Laid cardboard down & got my head & arm under the fuse box.. Wasn't able to remove the plug & ended up using my front phone camera to see how the relay had to go in, then was able to just get my left hand fingers on the side of it to guide it & right hand to plug it in. Didn't take that long either doing it that way, though I did mess with it for a good half hour the night before with no luck. The rest was as easy as it looks, might tweak the adjusters on the lights. They still have just a little movement but not bad. Love your vids man, thanks! Your shop & cars are very clean. I need to get my engine bay looking like yours ha!
I got mine today, got everything installed including the dang blasted relay (huge pain in my fingers) only to not have the lights turn on... After about 20 minutes of making sure everything was connected I realized that my switch is a bit odd. It has three positions even tho only 2 are displayed (on and off) apparently the left and right toggle are off and the middle is on. Only slightly inconvenient but the fog lights turn on and look beautiful. After 15 years my Green Machine finally has fog lights. Thank you for the awesome video!
Got them WORKING, the relay was hard! Posted some endoscope pictures that might be useful to others at scionlife, search for Relays Not Well Documented in EWD. Thanks Brandon.
My power wire wasn’t getting any power at the plug the relay and fuse were working fine so my solution was spend $30 and I just hard wired them to my battery and they work now so I’m happy
Sup man, love your channel. The extra plastic clips are incase yours break because of an accident or if you tighten too hard on the bolt. They are hard to find so keep them safe. Awesome 👍 channel again. Just did my breaks today after watching yours over and over.
Looks good bro. I have a 2005 midnight blue. It’s fun working on them. I couldn’t do the fog lights cause the car was salvaged front end so wires were cut. But great video car look great
@@ExtremeDailyDrivers yes like five times for the fogs you installed but i want the lower set like you originally had at the bottom i just got the set you installed in the video but want to add the smaller square one to the bottom of bumper
Dude happy later toaster Tuesday. I think u did a fantastic job on this. I really want an oem fog lights too. The oem with yellow lens with L.E.D. White would be perfect. The cool thing about it, is that our xB comes with those oem fog light plugs that just hangs there waiting to be plugged. And I thought it was gonna be a lot of work but no. Just remove the bumper, and plug it in and put the bumper back together. And that’s it. Always lookin forward to see more toaster Tuesday brotha.
Love the video just picked up and 06 with 95000 miles on it. I ordered the lights! But I would like to also add the lights you already have on there at the bottom! I ordered those also. Just need info on how to install. I’m new to the car stuff! Thanks I watched all your videos!
Little tip, you might wanna secure your foglights a little bit more around the back with zip ties or tape because mine only lasted a couple of month until one of them fell off, they seem like they're pretty secure but eventually they'll fall off with all the bumps.
That looks dope!!!!!! Lol I can't even dream of modding anything on mine yet, it's all just too nice as stock. Plus the original dummy inserts are all still there.
I guess they ship all of them like that. I know I told you that they had to be swapped around. You would think they ship it the right way. It's crazy.. But it does look good. I installed yellow LEDs in mi e and my Girlfriends xb. I am going to order the yellow housing for my Xb
Love the look! We like to see a pic of the fog lights @ night....Does it help with the visibility? I need to ship down my XB to you, so you can Pimp my Ride! 😂
I actually filmed some night shots, but the camera didn't do a great job showing light output. Every little bit helps, when I install some LED or HID bulbs it will really make a difference. Thanks for watching!
Man I love this video, I really wanna find a front face finisher, that thing is nasty, so yep more things added to my list of parts I need for mine, thanks, lol, keep up the good work brother
I noticed at 4:52 you have tapped something in the fuse panel, can you tell us about that or is it in another video? My EWD (Electrical Wiring Diagram) Pg 24 shows that fuse position as undocumented!
Hey everyone, so the harness for the fog lights are already there (the pig tails ) if I go under there I should have them on my kids car ?? For real please answer I'm not good at this DIY stuff but wanted to try with my kid , thank you
Got this same kit in today. Easy install on the lights and the switch. But I spent 45 minutes trying to get the relay into the socket with no luck. Any other tips on how to get it plugged in? there is a cut off zip tie back there that keeps cutting my fat hand lol.
Love your vid's I've learned so much about this car I believe I can rebuild this thing and make it better but for the relay for the fog light I can't figure out how to get it in need help thanks!!
.... and snap! I tried that with my xB and nothing, I've got the neighbors looking at me like I'm crazy. I'll try it tonight with the wife, hopefully it'll work then. The box looks f#ing burly dude! It would be cool to see a vid on a spray on the bumper, I need to do it on mine as well, and what's the deal with yesterday's teaser pic, when are we going to get a look at the interior?
@@ExtremeDailyDrivers I thought you bought the switch separately I see that it came with the fog lights now. I was just looking for the actually switch thanks though
I have a polar white 2006. Sweet color! Mine has no fog lights, but if it's pre-wired that year, does it mean I don't need to order the relay switch? BTW, I might be your only grandma/granddaughter subscriber pair. I'm 60. She's 9. We plan to mod up my stock ride a bit and love your channel.
All xB's come prewired, but you will still have to order the relay switch. Check the links in the description box to see everything you need. Thanks for watching! I'm glad you are enjoying the channel! Thanks for watching!
Will you ever do an intake manifold, i know the only on on market is 800$ weapon r but i remember you picked up the corolla one can you make a video looking into getting that thing installed
I really want to find a way to make it work. Throttle body is definitely going on soon. I wanted to make sure my intake was working perfectly before I start changing things up. So far it's passed with flying colors.
So question i know this is an older video... But i recently just got a Gen 1 Scion XB from an older couple, and was thinking of putting fog lights in... Do you have to havef to install a switch or is it possible to just have them come on when you turn the lights on? Maybe a dumb question im new to this sh!t.
Not that I'm aware of. Just plug it in, and turn on your fog lights. If they don't come on, you are in the wrong outlet on the fuse box. If you watch the video, I tell you where to plug it in.
@@ExtremeDailyDrivers look amazing who did it I love it and have 2 scion and I’m from Florida so if you have the person that did it let me know thanks 😊
![[#2024MAMA] G-DRAGON - 무제(Untitled, 2014)+POWER+HOME SWEET HOME+뱅뱅뱅+FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/Ox29z5Nf1Uk/mqdefault.jpg)
Do you miss your box Brandon ???? We do!!!! Lol
No! Enjoy the videos!
I look forward to toaster Tuesday every week I just recently bought the same pair of fog lights and are planning on installing them shortly
Awesome! I hope this helped.
Love it now I really want it done to my toaster
A huge tip for putting in the relay. You do not need to get on your back underneath the dash in order to plug it in. Simply reach around the left side of the fuse panel and plug it in by feel. The relay is plugged in with the vertical terminals on the bottom and the horizontal terminals at the top. Feel for the first 2 relays (they are located on the back left one on top of another vertically) and the fog light relay goes right below those 2. It is on the left side of the fuse panel when looking at the panel from the dash. Hope this helps. Took me 2 minutes to figure it out hope you can find it even faster with these tips.
Again, reach around from the left side of the fuse panel feel for the third relay location, and plug it in.
Good tip. Thanks for commenting.
This was a excellent tutorial, now I know that the 1st gen Scion Xb's come prewired for fog lights...this shows you how to make use of this option if your XB isn't fully equipped with fogs.👍🏽🇺🇸🇯🇲🌴☀️🌴
Thanks! Yeah, all 1st Gen's come prewired. It's not hard at all and for how inexpensive the kit costs it's kind of a no brainer.
@@ExtremeDailyDrivers 👍🏽🇺🇸🇯🇲🌴☀️🌴
@@ExtremeDailyDrivers do you know if the first gen bB are prewired aswell?
Do you have a BB?
@@ExtremeDailyDrivers yea -03 NCP35
It’s nice to see well put together xB videos. I like that you are posting DIY friendly mods that most xB owners want/plan to do at some point.
I appreciate that! The goal of this channel is to show people that working on cars is fun!
Notes on relay installation: I had to lay on my back with a mirror and light to find the relay socket and determine orientation. Once that was determined, I sat in the driver's seat and positioned the relay from the side of the fuse box. Pretty frustrating, but no way I was getting that thing in from underneath. Once I figured out how to get it in there, I was done in a few minutes. Thanks for the video. I would have been clueless how to get this done without it!
Plugging in the relay is the hardest part! I'm glad you got it!! Thanks for watching!
Easy peasy, Lemon squeezy! Nice job! The B is looking awesome and thanx to your video, I will be supervising my wife while she puts her fogs in soon!
That relay install is the hardest part!
Canada here...sweet B! Nice n clean...fender connectors...think about it...I love fog lamps! Dress up any vehicle!
Thanks 👍
Seriously...looking clean...what's next...airbag?
Can't believe its Tuesday already! Best fog light video yet!
I know!! Thanks!
This was very helpful, thank you. I'm going to install mine using the help of your video.
Glad it was helpful!
this is a great video, great instructions, about the headers, for couple decades ive been replacing and modifing. all i meant was that high quality is best way to go because there is a lot of r&d.
thats all
Glad you liked it!
The new lip and fff are nice. I love how easy these are to work on and customize.
Seriously. I always tell people these are easier than Legos. 🤣
@@ExtremeDailyDrivers they are, most things just pop off.
My new Favorite channel! Love all your work!
Wow, thank you!
Thanks for rhe help. Was stuck on swapping the mount ball ends.
Any time! Enjoy!
Thanks for the tutorial finally got my lights in and this made it easier
Great to hear!
Thank you for the video it looks great on my xB
Great job! Always looking forward to toaster Tuesday.
Me too! Thanks for watching!
Yooo I installed my fog lights today! Started with the hardest part - the relay. What a pain in the back! Laid cardboard down & got my head & arm under the fuse box.. Wasn't able to remove the plug & ended up using my front phone camera to see how the relay had to go in, then was able to just get my left hand fingers on the side of it to guide it & right hand to plug it in. Didn't take that long either doing it that way, though I did mess with it for a good half hour the night before with no luck. The rest was as easy as it looks, might tweak the adjusters on the lights. They still have just a little movement but not bad. Love your vids man, thanks! Your shop & cars are very clean. I need to get my engine bay looking like yours ha!
Hell yeah! Glad it worked!
I got mine today, got everything installed including the dang blasted relay (huge pain in my fingers) only to not have the lights turn on...
After about 20 minutes of making sure everything was connected I realized that my switch is a bit odd. It has three positions even tho only 2 are displayed (on and off) apparently the left and right toggle are off and the middle is on. Only slightly inconvenient but the fog lights turn on and look beautiful. After 15 years my Green Machine finally has fog lights.
Thank you for the awesome video!
Got them WORKING, the relay was hard! Posted some endoscope pictures that might be useful to others at scionlife, search for Relays Not Well Documented in EWD. Thanks Brandon.
Any time, Dude. Glad you got it!
thank you so much for this, i never knew this was so easy! It's going to be a new project of mine.
Nice! I hope you do! Thanks for watching!
Awesome video. Keep em coming. Toasters looking good.
Thanks! Will do!
My power wire wasn’t getting any power at the plug the relay and fuse were working fine so my solution was spend $30 and I just hard wired them to my battery and they work now so I’m happy
Very nice!! I have a purple scion manual ❤
Nice 👍
Sup man, love your channel. The extra plastic clips are incase yours break because of an accident or if you tighten too hard on the bolt. They are hard to find so keep them safe. Awesome 👍 channel again. Just did my breaks today after watching yours over and over.
Thanks for the tip and I'm glad I could help!
Looks good bro. I have a 2005 midnight blue. It’s fun working on them. I couldn’t do the fog lights cause the car was salvaged front end so wires were cut. But great video car look great
Thanks!
I need that deflector over the grill.
It's a FFF and they are hard to find, but not impossible. Thanks for watching!
@@ExtremeDailyDrivers i am looking for the lower set of fog light by the bottom lip where can i find those please?
Did you watch the video?
@@ExtremeDailyDrivers yes like five times for the fogs you installed but i want the lower set like you originally had at the bottom i just got the set you installed in the video but want to add the smaller square one to the bottom of bumper
sorry i see that part of the video now thank you, i may go with some simpler ones lol
Looks great 👍. Very clean.
Thanks 👍
Dude happy later toaster Tuesday. I think u did a fantastic job on this. I really want an oem fog lights too. The oem with yellow lens with L.E.D. White would be perfect. The cool thing about it, is that our xB comes with those oem fog light plugs that just hangs there waiting to be plugged. And I thought it was gonna be a lot of work but no. Just remove the bumper, and plug it in and put the bumper back together. And that’s it.
Always lookin forward to see more toaster Tuesday brotha.
Yeah, thank goodness Scion did the real hard work for us. Thanks for watching and supporting the channel!
Extreme Daily Drivers my pleasure. 🙌🏼
Thanks for this video, man.
My pleasure!
Thanks for the help homie!
Any time, Bro! #boxlife
CLEAN!! haha my fogs had the plastic spacers switched too! I thought it was made wrong 😅
After reading reviews, I think they are all that way. I have no idea why.
Thanks for this video bro. I will be adding the fog lights to my box soon. But first ingot a street glow green underbody kit that's will go first lol
Let me know how it goes! I will definitely be doing that in the future.
Awesome vid I used it to install mine thanks
Glad it helped
Love the video just picked up and 06 with 95000 miles on it. I ordered the lights! But I would like to also add the lights you already have on there at the bottom! I ordered those also. Just need info on how to install. I’m new to the car stuff! Thanks I watched all your videos!
Awesome! You'll love em'!
thanks bro... Good installation...
Glad it helped!
Little tip, you might wanna secure your foglights a little bit more around the back with zip ties or tape because mine only lasted a couple of month until one of them fell off, they seem like they're pretty secure but eventually they'll fall off with all the bumps.
Great tip. Thank you. I'll keep an eye on it.
That looks dope!!!!!! Lol I can't even dream of modding anything on mine yet, it's all just too nice as stock. Plus the original dummy inserts are all still there.
It's so easy! Go for it!
Lov the new look I just got me some new head light too Hahaha I love how it look keep the good work brother
Awesome! Thank you!
No problem 👍🏽👍🏽👍🏽👍🏽
Good job bro 😷👍🏻
Thank you!
Stock lip is sick
I guess they ship all of them like that. I know I told you that they had to be swapped around. You would think they ship it the right way. It's crazy.. But it does look good. I installed yellow LEDs in mi e and my Girlfriends xb. I am going to order the yellow housing for my Xb
You would think they would. Crazy. I will be going with yellow fog light bulbs too.
www.amazon.com/dp/B07GTD6FB5/ref=cm_sw_r_other_apa_i_NxISEbMVM8SBY
That is the ones I used on both our XBs
Please make a video of painting the body parts! I’d like some tips because my front bumper needs attention 😅
If my lower lip lasts a month, I will!! I'm not a professional so lets hope my prep was good enough!
Love the look! We like to see a pic of the fog lights @ night....Does it help with the visibility? I need to ship down my XB to you, so you can Pimp my Ride! 😂
I actually filmed some night shots, but the camera didn't do a great job showing light output. Every little bit helps, when I install some LED or HID bulbs it will really make a difference. Thanks for watching!
Any idea what the other pop out spaces were used for besides the fog lights? It this thing pre-wired for any other options? Thanks for the video
No, they are only prewired for fogl ights. Thanks for watching.
Hi friend my name is Dennis thank you for helping me install my fog lights Where can I find a face finisher it looks cool
It's custom made. Thanks for watching.
Love it
Man I love this video, I really wanna find a front face finisher, that thing is nasty, so yep more things added to my list of parts I need for mine, thanks, lol, keep up the good work brother
I always wanted a FFF on my first xB, but could never justify the cost. When I got this xB, I said, "Screw it."
What bulbs you have? Really like the white
Watch the video for the answer!
I noticed at 4:52 you have tapped something in the fuse panel, can you tell us about that or is it in another video? My EWD (Electrical Wiring Diagram) Pg 24 shows that fuse position as undocumented!
That will be coming up soon when I run a bunch of interior lights.
@Extreme Daily Drivers
I have a question the relay you put on the comments comes up as an ac conditioner does that matter ?
It's correct. It will work.
Does adding the relay allow you to turn on the fog lights with only the corner markers on or with the headlights on only like from the factory?
I don't think the fog lights will work at all without the relay.
Go extreme and add some new lights in the bottom bumper
Does it matter the unit of the relay one unit or two unit
Just get the one listed in the description. I know that one works.
Any idea where to look for a FFF it gives that awesome finish.
I got mine from Facebook.
What paint did you use for the bottom lip
Duplicolor
Hey everyone, so the harness for the fog lights are already there (the pig tails ) if I go under there I should have them on my kids car ?? For real please answer I'm not good at this DIY stuff but wanted to try with my kid , thank you
Watch the video for the answer.
Got this same kit in today. Easy install on the lights and the switch. But I spent 45 minutes trying to get the relay into the socket with no luck. Any other tips on how to get it plugged in? there is a cut off zip tie back there that keeps cutting my fat hand lol.
Pop the fuse box lose and you will have more room to pull in the relay. Good luck.
@@ExtremeDailyDrivers thanks my dude
That FFF tho 👌🏼. Where’d you get one to fit the USDM lights? You can also find some different knobs for your HVAC controls too!
It's custom. I will be changing my HVAC knobs soon. I have an interior video planned.
Love your vid's I've learned so much about this car I believe I can rebuild this thing and make it better but for the relay for the fog light I can't figure out how to get it in need help thanks!!
I pulled the fuse box loose and that made it easier. it was impossible to video, but if you look at it you will know what I mean. Thanks for watching!
Thank you ! I’ll try that and keep you post and keep doing those great videos!!
Do you have any additional info on the FF ? Been searching, and not coming up with anything .
They are really hard to find. Good luck!
@@ExtremeDailyDrivers SMH
Thanks for the great contents! does the lower fogs still works?
Yes! Believe it or not, they still did work after all the abuse they had been through.
.... and snap! I tried that with my xB and nothing, I've got the neighbors looking at me like I'm crazy. I'll try it tonight with the wife, hopefully it'll work then. The box looks f#ing burly dude! It would be cool to see a vid on a spray on the bumper, I need to do it on mine as well, and what's the deal with yesterday's teaser pic, when are we going to get a look at the interior?
Soon! I'm going to do an interior lighting video and I think I'll unveil it then for those who don't follow me on IG or missed the YT post.
New to the channel. Did you end up making a video of how you painted the grill?
Yep, check out the Scion xB playlist. I think there are 50+ videos in there.
Thanks for the video but where did you purchase the fog light switch I didn't see a link above...
In the description
@@ExtremeDailyDrivers I thought you bought the switch separately I see that it came with the fog lights now. I was just looking for the actually switch thanks though
I have a polar white 2006. Sweet color! Mine has no fog lights, but if it's pre-wired that year, does it mean I don't need to order the relay switch? BTW, I might be your only grandma/granddaughter subscriber pair. I'm 60. She's 9. We plan to mod up my stock ride a bit and love your channel.
All xB's come prewired, but you will still have to order the relay switch. Check the links in the description box to see everything you need. Thanks for watching! I'm glad you are enjoying the channel! Thanks for watching!
Will you ever do an intake manifold, i know the only on on market is 800$ weapon r but i remember you picked up the corolla one can you make a video looking into getting that thing installed
I really want to find a way to make it work. Throttle body is definitely going on soon. I wanted to make sure my intake was working perfectly before I start changing things up. So far it's passed with flying colors.
When will you do the sound system replacement 2.0 !?
It's probably going to cost the most, so not for awhile.
hey i wanna suggest cougar motor v16 led headlights. i've been using them in my xb and high and low beams are great. loving the videos! :D
Thanks for the recommendation and for watching!
Puedes escribir la medida de esas luces
So question i know this is an older video... But i recently just got a Gen 1 Scion XB from an older couple, and was thinking of putting fog lights in... Do you have to havef to install a switch or is it possible to just have them come on when you turn the lights on? Maybe a dumb question im new to this sh!t.
Yes, but it's cleaner and easier if you just follow the directions in the video.
@@ExtremeDailyDrivers will do, been watching your videos religiously for the last month. And thank you so much for replying!
@@nctrnlmjsty8719 Thanks for watching!
Hey Extreme Daily Drivers, do you have to remove the bumper??
It's easy, watch some of the previous videos. I show you how to do it 100 times.
@@ExtremeDailyDrivers Is there a diagram to plug the relay switch correctly?
Not that I'm aware of. Just plug it in, and turn on your fog lights. If they don't come on, you are in the wrong outlet on the fuse box. If you watch the video, I tell you where to plug it in.
Having trouble, I did everything and they don’t work :( . Idk if I put the relay in the right spot.
Sounds like you didn't.
@@ExtremeDailyDrivers turns out everything was correct, I just didn’t have my headlights on. Didn’t realize that was required lol.
Glad it was an easy fix!!! Congrats!
Mine didn't come with a relay, what should I do?
Watch the video. It has all the answers and links.
Front face finisher wait a minute I don't have that on my grill🤨
It's custom. They never came on the cars.
where can i get a face 🤔 finisher for my xb?
Man, I think I payed almost $300 to the dealer for the fog lamps when I bought the car. What a rip-off! But there were no aftermarket clones then.
Don't worry, I did too. We all live and learn! Thanks for watching!
Let’s make a xB club
Hello where did you get the front face finisher
It's custom made. Thanks for watching.
@@ExtremeDailyDrivers look amazing who did it I love it and have 2 scion and I’m from Florida so if you have the person that did it let me know thanks 😊
@@mollyjerrybullyz They were from Seattle and mine was the last one he made. That was 8 years ago.
Thats the only part i still want that i never found. It looked so good on your box.
POV drive for bb bro 😊
I was thinking of doing this!
@@ExtremeDailyDrivers yah yah bro i can't wait to see your POV'S videos
I need to find cool places to drive!
@@ExtremeDailyDrivers ok bro ride safe!
Hey man, what taillights are those?
Led from ebay
Give them the ilnk to buy them they are very cool!
😀😀😀🚗
Links for everything are in the description box! Thanks for watching.
thanks i found it 👍🏽
Any time!
How did you repair or fix that lower lip?
I sanded the heck out of it and it really didn't need any filler.
Oh wow that's cool. I'm looking into going to the junk yard and looking for both bumpers that's why I was asking.
Good luck. They are hard to find.
Thanks I will need it.
Where in Florida are you located!?! :)
Orlando
@@ExtremeDailyDrivers ok, sweet im in Daytona Beach and im on the hunt to get a nice xB
Mine had play in them after I clicked in it idk why
I'm sure you could easily fix that with some universal weather striping from Home Depot or Lowes.
@@ExtremeDailyDrivers i didnt think about that!! I just stuffed the packing peanuts that came with them inside lol
I need to finger out why my doesn't come on
You may have the relay in the wrong place or not plugged in all the way.
I'm going to miss with it today hopefully it will worm up it's only 30 outside here already lol
The harness for the button was put on backwards my nieces boyfriend lol 😂😆🤣