Hey! I m your new subscriber from India i have one doubt can i use p55nf06 MOSFET instead of irf3205 please tell me 2mosfet parallel connection on other side 2 MOSFET parallel please tell me
Thank you for the project. It may be sine wave, but I am not sure about the wattage using 2 Mofets and 5A /12v transformer. It is not mentioned in the descreption properly.
5000watt ke inverter par kaam karega ye ? agar karega to konsa transformer or konsa MOSFET lagaau or ye bhi bta dijiye ki MOSFET kitne lagaane hai please reply.
You haven't checked the waveform with an oscilloscope. Without a low pass filter on the outputs, you won't get any sine wave, transformer is vibrating means output is not a pure sine wave.
Hi bro, if you check the output signal in oscilloscope, you will not see sine waveform and without the correct output voltage of 230 ac. Don't confuse people.
@@homemade_101 Thank you very much for the quick response. Your explanation for building the inverter is clear. I followed it to the end. As a beginner, in electronics, I learnt a lot from it. My problem was how to build the feedback circuit. Please can you advise me in which page I can find the feedback circuit in the circuit diagram details you sent to me. Thank you so much for your help..
me sorprende que funcione, las placas de hierro del transformador la curva de histeresis con un controlador a 22.5 khz de pwm deben ser enormes. Pero supongo que para demostrar el concepto esta bueno.
Das Teil kann kein reinen Sinus, deshalb wird der Erbauer dir das nicht zeigen können oder wollen. Echte Sinuswandler sind PWM gesteuert, und bedürfen einen HF-Übertrager aus Ferrit und nicht einen Dynamoblech Transformator. Zusätzlich sind noch diverse andere magnetische Bauteile von nöten.
Hello, very nice video. I did the same but above 210V, voltage drops a lot even with feedback circuitry. I am using 220v/8.5v transformer from UPS. Do you think 220v/12v would be better ??? thanks !
*Are you sure that the output is 220V with a pure sine wave? With your proposed structure of two sides, each side having one MOSFET, I want to double or triple the power by adding multiple MOSFETs in parallel, and each MOSFET having a 100-ohm resistor for voltage division. Would it be stable? If possible, could you create a video showing how to add 4 to 8 MOSFETs on each side for reference, both for me and others? Thank you very much.*
TL494 Inverter 👉th-cam.com/video/UK_d7Upulr0/w-d-xo.html
how many capacitor voltages are you using in the feedback circuit
Terima kasih sudah mau berbagi ilmu, salam dari Indonesia
Kamu sudah coba mas?
kok gk bisa di download file nya bang
Best detail demo thanks brother. Increasing number of mosfets and power of transformer, we can get high power output
You are welcome
How many FET can be connected on egs 002 board?
Very good👍👍👍👍 video thank you
welcome bro
Hey! I m your new subscriber from India i have one doubt can i use p55nf06 MOSFET instead of irf3205 please tell me 2mosfet parallel connection on other side 2 MOSFET parallel please tell me
Sorry i mean instead of irfz44n
This project is very simple as compared to the full bridge complicated one.
thank you bro
7:10 por que el foco se apagó antes de desconectar el cable?
This is the best demonstration ive ever watch but nearly 100% perfect, sad but the video didnt demonstrated how to make the feedback of the inverter.
plz chek link. circuit
Theres no feedback circuit
Theres have feed back circuit@@ronaldbagaoisan5854
Bro Watch Full Video
Its Very helpfull. Thank you!
You're welcome!
Thank you for the project.
It may be sine wave, but I am not sure about the wattage using 2 Mofets and 5A /12v transformer. It is not mentioned in the descreption properly.
yes, you are right.
Not sinewave; you need a H bridge for that; an H bridge needs 4 Mosfets, cannot be done with only 2.
Does it working well with fan and no noise?
yes, good one. please check the circuit diagram.
Can I use 20N50 MOSFETs?
5000watt ke inverter par kaam karega ye ? agar karega to konsa transformer or konsa MOSFET lagaau or ye bhi bta dijiye ki MOSFET kitne lagaane hai please reply.
whats the watt output of this ? can this pure sine wave inverter power home appliances ?
yes. 200W
how many capacitor voltages are you using in the feedback circuit
25v
@@homemade_101 thank you so much ❤❤
Can the battery voltage be 20v?
\can't to this
@homemade_101 just try it first
Is it still pure sine wave inverter?
yes
can i ask u something sir? in circuit diagram, pin vfb and tfb didn't connect but in video is connect. which one is correct?
Diagram is correct. it is not need
Okay, thank you
Can i use 10ohm instead of 100ohm on G pin
ok
Здравствуйте если не секрет ка кие два резистора от диодного моста на потенциометре если вас не затруднит
На сколько Ом два резистора
100k resistors
Sir are you sure the out put voltage is 220 volt?
yes plese check circuit diagram 🤔
@@homemade_101 ok thank you 😚
The output is it Pure sine wave or modified
sine
Is this a 3000W inverter?
Yes but modification. Plz full circuit diagram have in description box
@@homemade_101 I'm not an expert in electronics but only with 2 mosfet it reaches 3000Watt? Ar you sure?
@@homemade_101 it will not be 3000 watts with a 5 amp transformer!
the overall system watt depends on what? number of mosfets in circuit ?
Can you tell me how many watts does this circuit with 2 MOSFETs produce?
200W
@@homemade_101 Thank you very much. Could you please tell me if I tested it on testborad first, is the power output stable?
Sir, can you please share the circuit diagram and the components used for the feedback circuit?
have in description
Please this transistor 1watts or 1/2 ?
1/2 w
Please i have 1/4 watts. Can i use 2 transistors?
@@Abouadam3851 yes no problem
how many watt can produce?
200W
How many watt output??
100W
I need 500W. Can you tell me how many Mosfets will have to use?
2, 4, 6, 8
Buen video 😊, en la parte trasera de la placa EGS002 como lo has configurado para la frecuencia ?? Y se pueden poner más mosfet en paralelo ??
sí, puedes usar más MOSFET.
Good job !!!
thank you
You haven't checked the waveform with an oscilloscope. Without a low pass filter on the outputs, you won't get any sine wave, transformer is vibrating means output is not a pure sine wave.
point
Sir, can you please make a tutorial on how to make the feedback circuit? It would be very helpful sir.
ok i will try
@@homemade_101 yes sir please, I want to make this project with the feedback loop.
Sir feedback circuit capacitor uf and voltage tell me
1000uf, 16v
Are you Electrical Engineer?
No bro I am Electronics Technician
😂
I can use 500W! what can change?
use mor mosfet
Super work💯💥& good job ..thanks for sharing 🙏😊
Welcome ☺️
Hi bro, if you check the output signal in oscilloscope, you will not see sine waveform and without the correct output voltage of 230 ac. Don't confuse people.
today I will uploading new sine wave inviter video. you can try it.
can you 1200watts diagram using egs002
or 1000 w
thanks you so much
@@chesterongoco6985
How to make the feed back circuit is not explained.
Circuit Diagram : drive.google.com/file/d/1qTExbPPKlaiAjgsL_e0Y9iCUIE8MeVLz/view?usp=drive_link
@@homemade_101 Thank you very much for the quick response. Your explanation for building the inverter is clear. I followed it to the end. As a beginner, in electronics, I learnt a lot from it. My problem was how to build the feedback circuit. Please can you advise me in which page I can find the feedback circuit in the circuit diagram details you sent to me. Thank you so much for your help..
me sorprende que funcione, las placas de hierro del transformador la curva de histeresis con un controlador a 22.5 khz de pwm deben ser enormes. Pero supongo que para demostrar el concepto esta bueno.
thanks bro
Como usa-lo em 24v?
12V only
Es wäre schön, wenn Sie die Ausgangswellenform (Sinuswelle) anzeigen könnten. Danke.
Diagram in description box. full Circuit diagram in
Das Teil kann kein reinen Sinus, deshalb wird der Erbauer dir das nicht zeigen können oder wollen. Echte Sinuswandler sind PWM gesteuert, und bedürfen einen HF-Übertrager aus Ferrit und nicht einen Dynamoblech Transformator. Zusätzlich sind noch diverse andere magnetische Bauteile von nöten.
Watt ?
100W
@@homemade_101 do you have feedback circuit diagram?
Hi. I believe the potentiometer should be 10K. In the schematics, you wrote 100K. Thanks for your video.
yes you are corrects
@@alessandrodonascimentovarg24 what would happen if we connect 100k pot
@@homemade_101 could uh help
feedback voltage required ?
can it work without temperature sensor ?
yes need a thermistor. chek data sheet
Hello, very nice video. I did the same but above 210V, voltage drops a lot even with feedback circuitry. I am using 220v/8.5v transformer from UPS. Do you think 220v/12v would be better ??? thanks !
Welcome bro.. Connect out put pins X rated capacitor. Parallel connect. No problem UPS transformer. Bus 12 0 12v transformer best one.
@@homemade_101 Hello, i did include a 2 micro farad in parallel with 220V output but still the same problem.
You could use it full h-bridge mode znd get more power out of it...
yes
I didn't see oscilloscope wave display
sine
With this configuration it has square wave, not to do with sine wave
...
yes
🍻🍻🍻👍👍👍
@@homemade_101
Ok, Thanks a lot
HELL.
HOW I CAN CHANGE THE FREQUENCY
plz check circuit diagrams
ගන්න තියෙන්නේ කෝහෙද
not download file😢😢😢
🤔
По вашей схеме не работает инвертор перегрев
Did you watch the video?
Comment je peux trouver ce circuit d'oscillateur?
Why my project is not 220v she is 190 v only 😢
disappointed😢
how much your supply voltge 🤔
12v 5 A
looks like you are to cheap to buy a piece of perf board????!!!!!!!!!!!!!!!!
Alliexpress
Gujarati translation
what
I have a far better circuit and it's pcb
Feed back circuit... can you make it look?
full circuit diagram has in the description box link.
*Are you sure that the output is 220V with a pure sine wave? With your proposed structure of two sides, each side having one MOSFET, I want to double or triple the power by adding multiple MOSFETs in parallel, and each MOSFET having a 100-ohm resistor for voltage division. Would it be stable? If possible, could you create a video showing how to add 4 to 8 MOSFETs on each side for reference, both for me and others? Thank you very much.*
ok i will try
Thanks @@homemade_101
This inverter can run induction fan??
i think can't
How much watt can use?
100W