Hello. I'm new, this is my first pair of glasses. I couldn't turn on OSD for half a year until I watched this video. Unbelievable. I already took a picture even to sell the hell out of these glasses. Thank You.
Sam Avella, done! Video was just released on how I installed the JST plug onto the Vista. I also attributed the video to your comment. Hope that's ok. 👍
My dji goggles v2 are also already in fcc mode. Allowing me to change from 25mbps to 50mbps. The display is twice as clear. Love it. Next going to add 1000 and 1200mw. 700 is the highest.
hello, nxp200, may i ask a question, i saw the osd on the right bottom side ,the RX signal (controller) cant activate, i have the same problem ,is it vista not support? thank u
I still dont have full use of osd. No GPS distance traveled or distance from home. I have altitude on display but gps speed only show in disarm mode after flight. I wonder if its because im using integra goggles not goggles 2.
The goggles shouldn't be the issue here. I don't have much experience in using GPS on my quads, but it may be configuration on Betaflight to show the correct numbers during ARM mode. Perhaps check you're on the correct OSD profile before flight
Hmm. Haven't seen that happen before. I would try another vtx (either digital or analog to see if the OSD chip is damaged). Or, check the Tx/Rx wires aren't getting shorted somehow after arming and flying around.
Hey ona separate note, before goggles 2 I had the naco.txt file on my vista, now with goggles 2, do I have to do anything to still have the extra video transmission power of 700w. IF so a video would be helpful. I am nervous about flashing my fc to 4.3.2 which is the last version available for the babyhawk 2 HD, does OSD work on goggles 2 at 4.3.2?
With the Goggles 2, you'll need to put an empty file named ham_cfg_support (no extension) onto a MicroSD card and insert it into the Goggles 2 before powering up. Then turn it on. This will put your Goggles into FCC mode. To check if this worked, go into Settings -> Transmission -> Channel Mode and switch it to Manual Mode. When you check the 40MHz bandwidth, you'll see 3 channels instead of 1. In terms of the OSD, it should work on BF 4.3.2. I have this video showing the instructions on how to set it up th-cam.com/video/gQFcvDB5RC4/w-d-xo.html
In the OSD settings in Betaflight, there is the option to turn on HD. Try that. I've noticed that sometimes that setting is buggy. So try turning it back to SD and then HD again.
I've tried to replicate this issue with BF4.5 but can't seem to see any issues with the size of OSD in HD mode. The only other thing I can think of is that there's an option inside the goggles 2 called "Settings - Display - Canvas Mode". There's SD and HD options. Select HD.
@@nxp200 I installed firmware 01.03.0000 on goggles..that was the problem. I couldnt choose canvas mode on goggles. Problem solved when i installed newest firmware on goggles
This depends on the flight controller. Some of them have plug and play connectors for the Caddx Vista and some require direct solder. In my case, I direct soldered to the flight controller the VBAT, GND, RX and TX wires.
www.printables.com/model/652970-impulserc-micro-apex-3-whoop-guard Edit: I forgot that this was intended to be used with the SwitchBlock I designed and the standard original camera mounting on the frame is not supported! Apologies for the mix up! I have redesigned it to allow for standard camera mounting and will print a test version before uploading the STL (to make sure it all fits dimensionally etc)
I just realised I designed this with my SwitchBlock, which means the standard FPV camera mounting is not supported. I'll remix to fix this and upload the new design. Apologies for this.
Hi, Sorry to bother you again. I forgot to ask you what fonts you used for your OSD? I’ve just setup my iFlight A65 that has a Caddx Vista with the Goggles 2 and the Fonts appear much larger than yours. Thanks.
No need to be sorry. Happy to try and help. The font is default after flashing Betaflight. In Betaflight Configurator OSD page, the front drop-down shows "font default" on mine.
Hi NXP! Fantastic video, really helped me a lot. I have one question though… after following this process everything worked perfect with the osd but when I went to fly today it was stuck in limp/low power mode. I assume this is something to do with the msp settings?? Have you encountered this before? Thanks!!
Hmm.. haven't had this happen before. Maybe you can try turning "Settings -> Control -> Auto Low-Power State of Air Unit" to "OFF"? That's how I fly, because if I crash and have to disarm, resulting in low power mode kicking in, I can't see the video to attempt turtle mode or locate where the quad ended up so I can search for it (as fast as I can before it overheats!). If that mode works, but you still want to have that option enabled, there might be some issue with the air unit not receiving the "arm" command from the flight controller. To which I'm not actually sure how to diagnose, sorry. If I get a chance anytime soon, I'll try to test it out on my system and let you know.
The carbon frame is an ImpulseRC Micro Apex 3 inch. The black whoop guards is my own design. I'll add the 3D STL to the video description soon for you to download if you wish.
I haven't done this myself yet, but you'll need to root the V2 goggles and install wtf.os software to get the OSD to work. It's different instructions than in this video. Joshua Bardwell does great instructions on how to do this.
Hello, I’ve managed to update the goggles 2 Vista unit and get everything to bind and show video but I cannot for the life of me get the DJI remote control 2 to work.. it just doesn’t show up in beta flight.. any help would greatly be appreciated!
Hmm.. sorry, I haven't actually tried that combination. I recall that combination with RC2 wasn't supported, but I could be wrong. Have you soldered the SBUS wire to flight controller?
Check out Nordic Drone Explorer you tube channel its called "HOW to connect pavo 20 with DJI fpv remote controller 2". I used this video to set up my pavo 20. There is a cls command you have to do.
@@dugy40 nice! I don't know what triggers it to automatically set it. I've tried numerous things but it's never done it for me automatically. Unsure if it's a BF 4.4 vs 4.4.1 difference 🤷🏻♂️ Glad it was sorted for you👍
Sorry, I've been quite busy with work and family. I can only think to check the TX and RX are wired correctly (TX from Vista to RX on flight controller and RX from Vista to TX on flight controller) and the correct UART is selected (TX1 and RX1 is UART1 in Ports tab).
@@nxp200 i dont mean you with i get no answer dont worry 😀 yes i did that. I guess something with the unit or the connection cable is wrong. Thank you for your help!
![☀ Глубокая настройка OSD на цифре. От А до Я. MSP+Displayport. [DJI FPV/Walksnail OSD Tutorial]](http://i.ytimg.com/vi/m5KcrF-uGRE/mqdefault.jpg)
Your a god you saved me so much time thank you so much! Happy New year to you bro
Hello. I'm new, this is my first pair of glasses. I couldn't turn on OSD for half a year until I watched this video. Unbelievable. I already took a picture even to sell the hell out of these glasses. Thank You.
Damn, you saved me today. I never used Vista before and I've been tinkering with this issue for the last two hours. Thank you.
this definitely saved me today. ive been bashing my head for the last few days. appreciated!
Dude YOU my god of drones! You is only one guy who solve my problem with OSD! Thank you very much!
I really ought to remember these steps by now but still coming back to this video each time I get a new drone 🙏
Trust me.. I go back to my own videos too 😂
Just so helpful as it’s not a task we perform often 😅
I haven't checked yet, but I believe there's a preset made just for this to make it easier. I'll do an update video when I get time.
Thanks so much for the CLI tip. I couldn't get the OSD to show up as well and didn't know about the command.
Thank you for the update and great video.
Interested in seeing how you installed the JST Connector to the CADDX. That’s a brilliant idea.
Cheers 🍻
Sam Avella, done! Video was just released on how I installed the JST plug onto the Vista. I also attributed the video to your comment. Hope that's ok. 👍
Great video! The last part is crucial 👍
Thank you so much for making this tutorial.😍😍😍
Awesome ❤
Thank you you just saved me the cost of 2 more o3 air units
Great video
Love the little breakout board too gotta get some of those 👍👍
Glad the video helped! I have a video specifically for that extra board I added to the Vista th-cam.com/video/4qIszB0ouxg/w-d-xo.html
Thank you so much for making this tutorial. 😊🙏🤝
Glad it was helpful!
@@nxp200 i have a question, hope that u answer. Can we set Canvas height and width OSD when we use Caddx vista like Dji 03 air unit?
do you know if this solution it works also on 4.5.1? because i no have osd
congrats!!! still working!
My dji goggles v2 are also already in fcc mode. Allowing me to change from 25mbps to 50mbps. The display is twice as clear. Love it. Next going to add 1000 and 1200mw. 700 is the highest.
hello, nxp200, may i ask a question, i saw the osd on the right bottom side ,the RX signal (controller) cant activate, i have the same problem ,is it vista not support?
thank u
its connected to the flight ,all good, just cant show the RX signal, sad........,anyone know why? thx
Thank you so much! I was looking forever for this!
I still dont have full use of osd. No GPS distance traveled or distance from home. I have altitude on display but gps speed only show in disarm mode after flight. I wonder if its because im using integra goggles not goggles 2.
The goggles shouldn't be the issue here. I don't have much experience in using GPS on my quads, but it may be configuration on Betaflight to show the correct numbers during ARM mode. Perhaps check you're on the correct OSD profile before flight
can you help sir. at first there is a display(osd ) after a minute it will be gone. any fix for this?thanks
Sorry. I can only think there is something damaged on the flight controller. Does it come back each time you plug in a new battery?
@@nxp200 it do it for me as well
Nice one, really nice video👌🏻
Hey
do you know what can be a problem if I see OSD for first 5-10 seconds after arming, but then it disappears?
Hmm. Haven't seen that happen before. I would try another vtx (either digital or analog to see if the OSD chip is damaged). Or, check the Tx/Rx wires aren't getting shorted somehow after arming and flying around.
Hey ona separate note, before goggles 2 I had the naco.txt file on my vista, now with goggles 2, do I have to do anything to still have the extra video transmission power of 700w. IF so a video would be helpful. I am nervous about flashing my fc to 4.3.2 which is the last version available for the babyhawk 2 HD, does OSD work on goggles 2 at 4.3.2?
With the Goggles 2, you'll need to put an empty file named ham_cfg_support (no extension) onto a MicroSD card and insert it into the Goggles 2 before powering up. Then turn it on. This will put your Goggles into FCC mode. To check if this worked, go into Settings -> Transmission -> Channel Mode and switch it to Manual Mode. When you check the 40MHz bandwidth, you'll see 3 channels instead of 1. In terms of the OSD, it should work on BF 4.3.2. I have this video showing the instructions on how to set it up th-cam.com/video/gQFcvDB5RC4/w-d-xo.html
@@nxp200 many thanks, found the ham hack, had it on my o3 just not my vistas
Thank you so much!
Hello 👋 can i bind vista to dji integra?
Yes it can. You'll need to update the Vista to latest firmware
@@nxp200 thank you
Thanks dude!🎉
im on Bf 4.5 and my osd is zoomed in. its kind of showiong all info but screen in goggels 2 are to small. Do u have any idee how to fix this?
In the OSD settings in Betaflight, there is the option to turn on HD. Try that. I've noticed that sometimes that setting is buggy. So try turning it back to SD and then HD again.
@@nxp200 thx. but i cant change after ive set msp on uart. It is on hd as default.
@@roarviksanderiksen Strange.. I haven't had this happen before. I'll try to replicate the issue and let you know
I've tried to replicate this issue with BF4.5 but can't seem to see any issues with the size of OSD in HD mode. The only other thing I can think of is that there's an option inside the goggles 2 called "Settings - Display - Canvas Mode". There's SD and HD options. Select HD.
@@nxp200 I installed firmware 01.03.0000 on goggles..that was the problem. I couldnt choose canvas mode on goggles. Problem solved when i installed newest firmware on goggles
Share the file for the ducts?
www.printables.com/model/655623-impulserc-micro-apex-3-whoop-guard-standard-analog
on betaflight 4.2.2 you can make osd with caddx vista?
I believe only 4.3 supports OSD with Vista
Great work. Did you solder any pads to the fc from vista or it’s a direct plug and play?
This depends on the flight controller. Some of them have plug and play connectors for the Caddx Vista and some require direct solder. In my case, I direct soldered to the flight controller the VBAT, GND, RX and TX wires.
Hi. Do you have the stl file of the ducts on thingiverse? Can you send the link please?
I'll see if I can dig it up and post it on printables for you. I don't upload on thingiverse anymore. Hope that's ok for you
@@nxp200 yes sure, no problem. If you point to me where to find it too, because I don’t know where “printables” is, I’ll be glad.
@@nxp200 lol ok, actually I found printables. I just had to Google it.
www.printables.com/model/652970-impulserc-micro-apex-3-whoop-guard
Edit: I forgot that this was intended to be used with the SwitchBlock I designed and the standard original camera mounting on the frame is not supported! Apologies for the mix up! I have redesigned it to allow for standard camera mounting and will print a test version before uploading the STL (to make sure it all fits dimensionally etc)
I just realised I designed this with my SwitchBlock, which means the standard FPV camera mounting is not supported. I'll remix to fix this and upload the new design. Apologies for this.
Thanks a lot Man, same problem, u are Angel ❤.
Where you able to turn on auto-recording on goggles 2 when you arm…?
No. Haven't been able to get auto record on arm to work with G2+Vista. There doesn't seem to be any options for it.
Hi,
Sorry to bother you again. I forgot to ask you what fonts you used for your OSD?
I’ve just setup my iFlight A65 that has a Caddx Vista with the Goggles 2 and the Fonts appear much larger than yours.
Thanks.
No need to be sorry. Happy to try and help. The font is default after flashing Betaflight. In Betaflight Configurator OSD page, the front drop-down shows "font default" on mine.
Does this also work with INAV?
I'm sorry. I don't know much about INAV to answer this.
Hi NXP! Fantastic video, really helped me a lot. I have one question though… after following this process everything worked perfect with the osd but when I went to fly today it was stuck in limp/low power mode. I assume this is something to do with the msp settings?? Have you encountered this before? Thanks!!
Hmm.. haven't had this happen before. Maybe you can try turning "Settings -> Control -> Auto Low-Power State of Air Unit" to "OFF"? That's how I fly, because if I crash and have to disarm, resulting in low power mode kicking in, I can't see the video to attempt turtle mode or locate where the quad ended up so I can search for it (as fast as I can before it overheats!). If that mode works, but you still want to have that option enabled, there might be some issue with the air unit not receiving the "arm" command from the flight controller. To which I'm not actually sure how to diagnose, sorry. If I get a chance anytime soon, I'll try to test it out on my system and let you know.
Got my sub! Very nice channel
Wow that's a cool frame you have! What is that? I've never seen it before.
The carbon frame is an ImpulseRC Micro Apex 3 inch. The black whoop guards is my own design. I'll add the 3D STL to the video description soon for you to download if you wish.
Saved my ass, thank you!
Can you use betaflight 4.4 on the dji headset V2??
I haven't done this myself yet, but you'll need to root the V2 goggles and install wtf.os software to get the OSD to work. It's different instructions than in this video. Joshua Bardwell does great instructions on how to do this.
Some values will work straight out, to get everything you will need wtfos.
Hello, I’ve managed to update the goggles 2 Vista unit and get everything to bind and show video but I cannot for the life of me get the DJI remote control 2 to work.. it just doesn’t show up in beta flight.. any help would greatly be appreciated!
Hmm.. sorry, I haven't actually tried that combination. I recall that combination with RC2 wasn't supported, but I could be wrong. Have you soldered the SBUS wire to flight controller?
Check out Nordic Drone Explorer you tube channel its called "HOW to connect pavo 20 with DJI fpv remote controller 2". I used this video to set up my pavo 20. There is a cls command you have to do.
Thank you!
Motors are you running?
iFlight Xing 2 1404 4600kv
Thanks
What commands did you type?
set osd_displayport_device = MSP
save
@@nxp200 I just moved my stuff around and when I went to cli it automatically did it. Didn’t have to type anything.
@@dugy40 nice! I don't know what triggers it to automatically set it. I've tried numerous things but it's never done it for me automatically. Unsure if it's a BF 4.4 vs 4.4.1 difference 🤷🏻♂️ Glad it was sorted for you👍
gogles V2 and vista nebula \
No osd
i did all of this but still doesnt work.... anyone else having the same problem?
i got the problem too
@@alessandrodimartino1872 still got no answer. I ordered a new unit and a new cable. Hope its only the cable
Sorry, I've been quite busy with work and family. I can only think to check the TX and RX are wired correctly (TX from Vista to RX on flight controller and RX from Vista to TX on flight controller) and the correct UART is selected (TX1 and RX1 is UART1 in Ports tab).
@@nxp200 i dont mean you with i get no answer dont worry 😀 yes i did that. I guess something with the unit or the connection cable is wrong. Thank you for your help!
which firmware are you using? in sight and in glasses. here does not work osd with vista and integrates.😢
LOTS OF BUFF. but good knowledge. thank you. goggles bit missed on lots of videos
Your lq isnt working?
Yeh. I didn't turn on my controller for this test. I just wanted to set the OSD working