@@SRTpj392 on the wiring side, probably 45 minutes to an hour and that’s only because it was my first time ever doing it trying to find out how to route the wires and wires to cut. I got my exhaust spark plugs welded so that is a different time but if you was to screw in probably another 10 minutes.
I remember doing this back in the day with MSD box and spark plugs my car now can do it on its own not as nice as your flames but it will do it in between shifts engine brake and at stand still. loud pops when it has E85 but no flame tho good video tho for those going to do the kit install
So this maybe a stupid question But.., the spark plug that is inside the exhaust you never have to change the spark plug they just last forever like that..?? Its crazy because ive never seen a spark plug welded inside of a exhaust pipe before. Any information on this would be helpful before i purchase for my scatpack. Great video keep the content coming
Yo thank you. So Ive installed this and ran into an issue. I tapped into the wire at the connector into the fuse box. I am assuming that is why I get spark but no flame. I guess because of the relays, doing it at that point causes the power to be cut from both the ignition coils AND the injectors. Gonna rewire it tomorrow lmfao
Apart of the kit. How to make it pop (aka gun shot) accelerate press and hold button - after acceleration while holding the button - tap the gas pedal once After tapping the gas pedal release the button it should make the gunshot sound. This is all very fast not a slow process. within 2 to 3 seconds, you should have completed what I just told you anything longer than that you will only make a flame or not do it at all.
Idk if anyone is having the same issue but when i do it for some reason my car starts giving me check engine codes “ignition coil A-F” and fully disconnects the throttle and dies all the way which makes me think its a safety feature but idk how to remove it or why does it do that
It may be low rpm. And how you push the throttle and how long you hold the button. When I first got the kit and was learning how to control it and do different things. My car did the same thing, but the check engine light always goes away after the car resets itself and or sees that no longer issue definitely a safety feature on the new model chargers, nothing to worry about since I put this kit on my car.
Yeah i found that the best way is to hold it for like 2 sec and release and press again for 2 sec and release for the best to get the flames without your car disconnecting everything even while it is at 3500rpms, that’s the best way with anyone is dealing with this
If you have a charger, it is definitely there. You have to sort through all of those wires that you see in my video. It just may be well hidden. It is a half and half like 16 gauge wire maybe a little bigger I’m not all the way knowledgeable on gauge Wires, but 15 and up chargers that is the wire you need to look for. I hope you find it.
Only video that shows the wire to splice in the fuse box
FACTSSSSSSSS thanks for watching. 🫱🏽🫲🏾
Yup i hate how no one talks about it. Great video man thanks
@@SRTpj392 on the wiring side, probably 45 minutes to an hour and that’s only because it was my first time ever doing it trying to find out how to route the wires and wires to cut. I got my exhaust spark plugs welded so that is a different time but if you was to screw in probably another 10 minutes.
THE ONLY VIDEO THAT EXPLAINS IT PERFECTLY ! THANK YOU BRO❤️
Glad it helped!
W video 🔥
I remember doing this back in the day with MSD box and spark plugs my car now can do it on its own not as nice as your flames but it will do it in between shifts engine brake and at stand still. loud pops when it has E85 but no flame tho good video tho for those going to do the kit install
So this maybe a stupid question But.., the spark plug that is inside the exhaust you never have to change the spark plug they just last forever like that..?? Its crazy because ive never seen a spark plug welded inside of a exhaust pipe before. Any information on this would be helpful before i purchase for my scatpack. Great video keep the content coming
You don’t have to weld it, you will receive a nut with the kit and you will be able to tighten it with that yeah no need for welding
I don’t even own a cat yet but video was informative 👍🏾
Speak it into existence 💪🏽
The kit that you have did you get single or Dual
Dual
Yooo i splice the wire that was shown in the video the yellow n black wire and it still didn't spark.. can the button itself be a defect?
U may have the connection backwards going into the button. Try swapping it before you request a replacement kit
Yo thank you. So Ive installed this and ran into an issue. I tapped into the wire at the connector into the fuse box. I am assuming that is why I get spark but no flame. I guess because of the relays, doing it at that point causes the power to be cut from both the ignition coils AND the injectors. Gonna rewire it tomorrow lmfao
How is it going ?
For it to pop while driving is it that part of the kit or did you tune it as well for pops
Apart of the kit.
How to make it pop (aka gun shot)
accelerate
press and hold button - after acceleration while holding the button - tap the gas pedal once
After tapping the gas pedal
release the button
it should make the gunshot sound. This is all very fast not a slow process. within 2 to 3 seconds, you should have completed what I just told you anything longer than that you will only make a flame or not do it at all.
Idk if anyone is having the same issue but when i do it for some reason my car starts giving me check engine codes “ignition coil A-F” and fully disconnects the throttle and dies all the way which makes me think its a safety feature but idk how to remove it or why does it do that
It may be low rpm. And how you push the throttle and how long you hold the button. When I first got the kit and was learning how to control it and do different things. My car did the same thing, but the check engine light always goes away after the car resets itself and or sees that no longer issue definitely a safety feature on the new model chargers, nothing to worry about since I put this kit on my car.
Yeah i found that the best way is to hold it for like 2 sec and release and press again for 2 sec and release for the best to get the flames without your car disconnecting everything even while it is at 3500rpms, that’s the best way with anyone is dealing with this
Whats your b pillar design called that looks gas🔥
Black forged carbon wrap
Ik this old but when I hit the button there’s no spark in the back or nothing just the check engine light comes on is it not wired right or what?
Message me on instagram and I’ll help you figure it out my instagram is techdk23
I got the same kit how do you make it pop?
Video coming this weekend on How to make it pop
Do I need to delete the cats?
Yes
Where did you buy the kit at?
www.hotlicksexhaust.com/
I cannot find that particular wire in my scatpack
If you have a charger, it is definitely there. You have to sort through all of those wires that you see in my video. It just may be well hidden. It is a half and half like 16 gauge wire maybe a little bigger I’m not all the way knowledgeable on gauge Wires, but 15 and up chargers that is the wire you need to look for. I hope you find it.
@TechDK23 how long did the Installation take total
How do you make it pop like that at the end of the video ?
Hold and release button for 1sec it will pop.. make sure you take your cats off or the cats will prevent that from happening
Video coming this weekend. On how to
Hey boss, could you give a tutorial on how to shoot flames while driving ? I need to know from the best 🔥
I got you. A few people been asking for it
THANK YOU 🙏🙏🙏 I’ll be waiting for that notification 🔔
@@Infernogt19video coming out this weekend sorry for the delay.
@@Infernogt19 Yeah please
a bit late but could you link all the stuff you said in the video it was a bit hard to hear them
This is a must for any V8 car
Mannn a poor man’s tune
hey bro, saw you today in upper sandusky in the scatpack at mcdonalds. w car i was in the explorer at the gas station
Video coming soon for wat I was doing that day. Thank you for tapping in 🙏
Fire video but dont go to that muffler shop again them welds are garbage
Facts😂
FACTSSSSSSSS. 😅