Fantastic hands on teaching. I've been bandsawing for only 63 yrs and I still picked up one new trick from you today. Your shop cat is a wonderful Plus. We love him!
Jesus. You covered two mistakes I made that lead to serious injury. Thanks for mentoring those who simply don't know until they get hurt. 30 years on the bandsaw and your high siding workarounds taught me something. Good job.
Your bandsaw spoon video really made me so interested in woodworking when I was 13. Im now 21, and have an entire shop! You have no idea how much one video has influenced my life.
Thank you! If the blade is sharp. It will be fine. If it’s dull I bring the guard down closer. To have more control… but I often keep it higher for more view
11:34 I'd hazard a guess that most shop saws have a much wider blade (.5" or higher) and they won't make the curve without the relief. Or they just don't trust the kids to cut without binding the blade.
@@derschwartzadder as a shop teacher, I can confirm that I don't want students binding the blade, I do try to keep two bandsaws with two different blades, a small one and a resaw one but kiddos aren't always mindful of which blade they're using so I could see enforcing relief cuts due to that. Also as the blade gets abused it's kerf is less wide and thus doesn't allow for tighter turns. Raising the guard up like jimmy does does help with blade maneuverability but again the teacher in me requires students to keep the guard down low in an effort to reduce injuries. Safer all around to have dumb facets on their piece that they can sand away with the spindle sander or disc sander. My rule of thumb is "if the curve is smaller than a coffee cup, use relief cuts. Also: shame on those shop teachers that don't make sure their machines are in safe working order, it's literally part of our job! (and kind of a fun one at that)
Thanks for the video. Jimmy. I knew some of the tips but there were a lot that I did not know.Somebod you refreshed my memory and taught me a whole bunch period
For some, experience is the best teacher, but much can be learned from sharing dos and don'ts. I found most of what you shared from my experience, but found two steps very helpful. (e.g. sacrificial piece for zero clearance.) All in all, very good vid. Certainly do more like this. Power tools and hand tools are slowly becoming a lost art due to tech. So for posterity...
Not only are you a great teacher, but you do it with a sense of humour. Reminds me of my days in a metal shop, as a teacher. One of my favourite comments at end of a safety lesson was, "and remember,( I paused), you don't want to set yourself on fire". Great tips, thanks.....
Some kid in my school shop caught on fire because he wasn’t wearing any protection other than his cotton shirt and his shirt caught a spark. He’s fine now
The one tip I use often that you didn't mention is that pulling material through the bandsaw is just as valid a method as pushing it through. So if you are cutting a straight or curved cut on a longer piece, start the cut by pushing the piece into the blade, then when you are halfway through the cut, with the piece fully supported by the table, walk around to the back of the saw and pull it the rest of the way through. This lets you support the workpiece throughout the cut and it will not want to tip upwards due to gravity
I have good outfeed support for the ts...so balance / tipping isn't as tricky. It also makes the walk to the other side longer. I also worry about kickback when I let go of the piece... But with smaller contractor saws, you can pretty easily walk around it without letting go, especially for sheet goods.
I agree with all the positive comments, great explanation of all the mistakes I’ve made! One additional thing I do, as you said, to back out of the cut, turn off the saw first. Sometimes I also, AFTER TURNING THE SAW OFF, I insert a small shim at the start of the cut, usually widens the whole cut to make it easier. Would also work with the saw running, but would be really dumb to be that lazy.
I miss this type of instructional video contest from you Jimmy. Takes me back to the NYC shop days. Yes, there may be other videos available how to do something, but the community trust you and what you teach. Keep on keeping on brother! Dining table build videos are always appreciated.
I've been using band saws for a few years now and have learned a lot by trial and error. I appreciate all that you presented in this video and learned a few things that will deffinately serve me well. Thanks and best wishes for continued prosperity.
I don't know you but I was just wanna let you know how much I appreciate getting guidance from a complete stranger with 50 years of bandsaw experience. Thanks man
You can only say "No" to somebody, so many times. The real trick isn't to not turn the rejection of a premise into a challenge, but to have the idiot comply.
The BEST bandsaw use video I have seen with lots of common sense. I tend to trust guys who do videos who have all their fingers and fingertips. He admitted to being cut, who hasn't, but losing a finger shows some flaw in the user. Thank you very much.
Mr. Jimmy, I am 52 years old and I JUST got my FIRST band saw. I don't know (correction, didn't know) anything about it, until I watched your video. I STILL don't know anything about it, compared to you, but I definitely feel more prepared and informed having watched your very informational video. Thank you for sharing your considerable knowledge with all of us on the Internets! Shalom and happy Bandsawing!
I'm 63 and have been breathing sawdust since I was about 10. But I always love learning something new, and that's why I appreciate videos like these. One thing that I see a lot of (with a bandsaw) that concerns me is the distance between material and the upper blade guard. I was taught to adjust it to about 1/8" to 1/4", as that will not only reduce the chance of skin to blade contact, but reduces flex in the blade... sturdier blade equals less drift and deflection. But I'm always seeing people on TH-cam with 6" to 8" of clearance. Usually, these are the same ones who wear gloves at the table saw, so I consider the source, but I notice you -- who are vastly experienced -- also had a large clearance. I'd love to know your thoughts on the matter. (Thanks for all you do)
EXCELLENT VIDEO! I’ve been bandsawing since I was 12 (I’m 62 now), and I gradually learned and applied all of these practices, especially after almost losing a thumb at 14). My dad was an artist who let us use all his machines, but there was ample training by him (esp. after my accident 48 years ago). I’ve not had one bandsaw accident since then. So much great info here! Subscribed and will save this clip to show others.
Jimmy, I've used a bandsaw for 25 years, and I can still learn a trick or two from you. One trick I have for you regarding cutting outside curves with a wide blade: I know you don't like relief cuts, but what I do is make relief cuts just shy of the cut line...about 1/16-1/8" from the line. Then when cutting the curve, I can do it in one smooth motion keeping the blade in the cut line while the wood bends and breaks away where I cut the reliefs. Works great without stressing the blade or creating the flats you mentioned in the video.
Amazing Jimmy. I’ve probably made all of those mistakes over the years. I honestly think this is one of your best videos you’ve made. Also, very cute cat.
Yes, to answer the question would I like more of these. FYI, I wholeheartedly concur about how dangerous those aggressive resaw blades can be. Bought a new 4tpi 3/4" blade back in January. Barely bumped it while installing it and adjust tension using the "flutter" method. It pulled my left hand right in. I'll never have full function of my left thumb or full strength in it again, but at least I still have it. It only takes a fraction of a second's loss of concentration. Thanks for the videos!
Oh my gosh that's awful! I caught my thumb in a tablesaw blade back in high school and I'm so glad I still have it, and really happy that it's still fully useable (still have a big scar but i can live with that.) I'm actually more afraid of my 16" bandsaw than I am of my tablesaw.
I just purchased a 14 inch band saw and kind of hate using it. After watching this video I was surprised how you hit on nearly every mistake I am making. This is a great video that gives me hope for future projects. Pencil is a great idea as a push stick. I worked in the ER for 30 years and have seen these take off a finger. Table saw was number one culprit in shop accidents.
PRICELESS......This should be required viewing in all HS shop classes as well as a DVD packed in with all new bandsaws. Thanks for the refresher course.
You probably have gotten this comment more times than you could read it but I would pay ANYTHING I could to apprentice at your shop. I am desperate to learn how to carve the way you do, and feel like I learn so much better by watching in person and doing by hand - and having someone there to be like "dont do that." In the meantime, I will watch everything you put up. Thank you, thank you, thank you.
I can wheel a chainsaw, use a chop saw like nothing else, handle a circular saw without a problem....I have a tabletop band saw from Craftsman that I'm scared to death of using. I do feel a little more confident now that I've watched this. Thank you Jimmy...yes, more videos like this. Someone mentioned a table saw.....that would be great! I have one of those, too, that I've used but still leary about cutting with it.
Long time since I've used a band saw, but I just bought an old one a little while ago. I fixed it up and now she's ready to go and your tips have reinforced some old Tekneek's I used a long time ago. THANKS for helping to clear the cobwebs.
I love this! Yes, please make more of these types of videos. (Maybe a table saw one next? Or drill press?) Crazy how many of these things I’ve done or thought were a good idea. 😵💫 You are the best, Jimmy! 👊🏼 #DIRESTA
What a refreshing informative video. Such a change from all to many TH-cam videos where the “how to” is in fact “ how not to”. They frighten me so much!
Very timely! I had a small (10") crappy bandsaw that always tipped and was frustrating to work with. One day it dropped and cracked and I went without one, but over time felt the need for one, so I am now close to finishing my own bandsaw based on Mathias Wandell's 16" model plans. Looking forward to being able to do what you do! (in about 50 years)
In my 50 years of woodworking, I have done only a minor amount of band sawing compared to using other tools to complete my projects. Your advice is the best. Knew of some by trial and error - still got all my fingers! and yes, only use a sharp blade. A community saw that I was to work with was hard to push and heat up and was told that I was working it too hard. I went a bought a new blade and put it on for just my project and the others in the shop wanted to know what I did. I told them and also told them that they should invest in their own blades. I took my own blade home with me.
Love this type of video! Reminds me of your older tool training vids. We can all use a drill, but it's awesome learning tips from someone with 6853256 hours of drill usage.
I thought I was the only one still using that antique Delta Milwaukee bandsaw! my wife found mine 25 years ago at a yard sale. I just made a fence for it today. I like your videos you tips will come in handy.
I have that same bandsaw, a 1948 14 inch Delta that my grandfather bought new. I've been using it since 1960. What a great machine. It is as old as me! In all these years, I have only been bit on the thumb ONCE. And believe me, it taught me a good lesson! Your tips are so spot on, I learned a few things too. You have gotten a subscribe and a thumbs up from me! Thanks for a common sense video.
Thank you Mr. Diresta for such amazing videos, i've been a long time subscribers now and it's been a long time since i've had the time to watch one of your videos. i'm starting to work with wood and those tutorials are amazing. It'd be great to have more videos like this one on different machines
great video, when i saw it on list I thought I don't need to watch that, I already now about bandsaws, then decided , oh all right i'll give it a minute. Watched whole instruction, and I learned lot more than nine things, THANK YOU
Relief cuts are often necessary when removing material from inside of a curve while using a wide blade. And if they are not absolutely necessary they certainly make the task easier. With the wide blade, Jimmy just made a series of MANY small relief cuts. But without a doubt his method of doing it works well.
Students are hard on the equipment. They twist the blade and pull back on the wood when they cross their line. Relief cuts on an inside curve saves me from replacing snapped and kinked blades too often.
My first time watching. I am 62 and these are some of the best examples I have seen. You sir are a pro. Thanks for sharing your life long experience. Bws
I'm the safety coordinator where I work. Several years ago, I was showing a novice 16 year old how to use a bandsaw. The very first thing I told him was never ever stick your fingers in the blade. I was very adamant about that and repeated it several times. He got halfway through his project, and what's he do, sticks his finger tip into the blade . It wasn't a bad cut, but his parents thought he should go to the emergency room. We spent 4 hours in the ER. I told him that little cut would probably be healed until you get to see a doctor. He got two stitches, and the away we went. My point is that when it comes to safety, listen to what you're told.
If you are in charge of safety and someone got hurt the first time they worked with the tool you were teaching them on then you are not doing your safety teaching job right.
Great video! I bought my first bandsaw about a year ago and since then I think I have made all 9 of your errors. Too bad I just found this video. You really are a talented craftsman and gifted teacher. Thank you.
Great tips, Jimmy, thanks. I saw a tip a few years ago that I incorporated as an experiment. It was helpful (or an illusion of helpful). Using a fine stone, diamond file, or steel file you simply dress the back of the blade, while it is running, to soften the hard edges. The theory is it reduces drag while doing curved cuts.
As a hobby carpenter, i find your advise is very good, and i try to follow it each time I use my very old "general" band saw! Also it does not have some of the adjustment capability that the more modern band saw has! I do a lot of adjusting by trail and error, so yes, your advise is most welcome when I'm preparing to do a little project, 'bird house - mantel clock - large & small lettering etc. keep doing what you are doing!
I did a double take-I have your saw, Delta/Milwaukee 14”, made in 1943. I know because I called Delta in Tennessee. The woman looked up the serial number, which was still in the files. I asked if they had a manual, which they do, so she sent me a copy. It’s hilarious to look at the prices of parts in 1943-bearings were like a buck and a half. Still working 80 years later. Got it from a guy for $300, replaced the 3/4 HP motor with a 2 HP dust proof farm motor (for conveyors), and that saw won’t bog down. I’ve been using it for over 30 years, and it’s one of my most used tools.
This is the best Video on TH-cam. I have seen so many folks with missing hands or digits it scares me to think about it... This video is TOPS for safety ! ! Thank you so much, BTW keep your Kitty indoors and safe, love that Kitty !! !
I know this video is over a year old but, thank you very much. Just got my first bandsaw (a older, used bench top model) a few days ago. I was really struggling with what I thought should have been simple cuts. When you showed the blade guides and bearings on your saw, I realized my saw was set up incorrectly. Now that I've corrected the setup issues, it cuts much better. Just need some more practice now lol. Thanks again.
I recently finished restoring a Tanner bandsaw made in Auckland New Zealand in 1952 and have been watching quite a few videos. This was the best one yet.Very helpful.Great vid. Especially the part about the upper guide setup and the pencil idea.
Well done. As a retired stair builder I have hundreds of hours on a bandsaw. Mostly resawing but also scroll type work, especially with making easements. I still get asked questions all the time about bandsaw usage. I will happily save this link and tell folks: watch this video!
Great video! The BEST tip I got was using the push stick to turn off the camera! LOL... seriously tho it is obvious your experience has superseded the books and many pros. Letting things fly on the how not to's is the best teaching anyone can give. It is always beyond a beginner's ability to grasp the physics of just how quickly things go wrong. Watching it makes them think much more clearly... and doesn't let them get to brave to quick. My woodshop teacher did this (many years ago- before EVERYTHING had guards on it) with all the power tools. While he scared a few nerdy kids (with flying shtuff), everyone ended the year with all their fingers and all the bandaids stayed in the box. His table saw kickback lesson landed a 3 footer scrap across the shop , across his desk, and slammed his empty chair. Whereupon (without missing a beat) he proclaimed in a drill Sargent's manner if anyone did that they have failed woodshop haha.. Got a few laughs but it never happened. Thanks for sharing.
Superb video, I am a beginner woodworking self-learner, just bought a band saw and love it. Thanks for passing this wisdom and knowledge to us. With 50 years of experience, I think you should be standard for anyone making bandsaw videos. 😊
I've been using a bandsaw for 45 years but you can always learn! Love the pencil idea, I always just used a scrap but the eraser of the pencil is a great idea. Thank you!
I've owned a bandsaw for 10 years and it's the one tool I really struggle with. This was a brilliantly helpful video - thank you. I will watch it again and start to implement some of your advice. My nemesis is trying to get straight even cuts whilst resawing to create thinner boards, I would be grateful for advice, guidance or a video even. Thanks again for sharing what you have learnt.
Just recently got.this bandsaw from my father's work. '75 rockwell 14". Mostly original equipment. Still.runs great. Had to replace the tires, balance the wheels and get new blades, what a solid saw.
Mr Diresta , you’re a jack of all trades. A very intelligent extremely talented and innovative and man. You now and then fabricate one of a kind off the wall high quality items . Many of these one of a kind off the wall items will overtime become very valuable collectors items. Once a month I will binge watch all your TH-cam Channel Videos that I have not previously watched.
I loved this and the amount of flinching I was doing watching you show what not to do tells me you're showing some important stuff. I also REALLY love this is your band saw from when you were 7. That's terrific!
Thanks for posting ! A couple of other tips I learned over my 30 years of amateur (very amateurish!) woodworking I give here for what it's worth. 1) Adjust the height of the blade with the height of the object, this way your blade will not wobble with a chance of breaking. 2) If someone watches you using the bandsaw they should never look at you from the side, but always in front or at the rear of the machine. If the blade breaks if some part flies of it will do on the side thus hurting badly the person who's on the side. A very unlikely thing to happen… except that I saw it once 20 years ago. These are onoy my two cents that I post because they are very easy to follow… Again thanks for those sound advice …
Well I absolutely love this. It reminds me of the machinery I used to see around me in workshops as a child, young man. Almost always accompanied by the smell of oil. Thank you.
Always good to learn new/different perspective... specially from someone very knowledgeable. I recently had a friend over to cut his project... as I was about to say this is the safest machine in the shop... Whoaa... blood spurts. Can't attach photos... or I would. (blood spattered on the floor, none on machine!, put the crime scene body cutout on floor) With the dust collection system running it can be that you don't realize the saw is still running as you clear the table as the victim did. Not a deep cut, but he stopped at his DR office for an opinion. It's something I coulda done... So... I constructed a circuit AC to DC to power a 10mm LED... and wired it into the saw... such that when the saw is on, a bright LED shines on the table top. Providing a visual reference .ITS ON..!!. Thus far, 38 accident free days. Felix
Thank you - good tips, clear illustration in use, clear English articulation and grammar (SO many fall down on this) and always to the point. A well-chosen speed of delivery meant that I could happily sit through the tips I knew already (as I knew they wouldn't take long) and at the same time, could just about keep up with the ones which were unfamiliar. Bravo!
Awesome, thanks very much. I have a new Grizzly bandsaw and really respect it. I've been running chainsaw commercially for over 50 years and have all my fingers. When I demo 'd a different brand, the salesman almost lost some fingers when he tried to cut some white oak round wood that I brought to test the saw. Apparently he never watched video of do's and don'ts on bandsaws, so thanks again.
Great video! I just purchased a used Jet 14" bandsaw yesterday, and spent a couple hours setting it up. I should have watched this first, as I now realize I didn't set the bearing and guide blocks correctly. Thank you for the safety tips too, I'm a professional musician, and my fingers are my extra important to me!
Thank you for the tips and explanations, I’m a retired mechanic and as a carpenter, I’d make a good butcher. I’ll watch you videos now to see what else I can learn, Ken from Australia.
I've been to lazy for years to buy a smaller blade for years and stuck with the technique you showed for tight curves with a larger blade, seeing how easy scroll cuts are for you with that small blade once I get home I'm ordering an assortment of different size blades because I think I will use the bandsaw more and to more of its potential, great video thank you
THanks Jimmy. This has been the first of your videos that I've watched. I subscribed immediately , not because I need the advice as I am an old luthier who has run the same Italian bandsaw for forty two years now , but because you presented a well thought out no bullshit guide that will be valuable to a new user. I particularly endorse the whole body method for curves .Yes, calm and steady , Be the cut.
Thanks for the reminders - for me. I'm 72 and have been using shop machines since I was 13. Never an accident! (yet) I was taught that sharp is safe. A sharp blade or bit is so much safer. Respect the tool, let it do the cutting or drilling and love your body parts. Oh yeah - don't use your machines when tired or in a rush. My shop teacher said to think of cutting a stick of butter with a stick or a sharp knife. Great video - thanks again...
Good tips I use a Shopsmith 11 inch bandsaw and it works for me. For the rip fence I use a 4 inch aluminum angle iron with welding vice grips on both ends to keep it straight. You definitely know your bandsaw. You should be a shop teacher. Thanks
Thank you so much for the vid. We are opening a woodworking shop and (they) bought a bandsaw for it. Knowing the insurance company and the kind of people who will be using the shop I'm putting together a workshop for bandsaw beginners (and after doing so I'm gonna shit myself based on my tablesaw workshop and the hard-headedness of so-called experienced people). Your video helped me to order the subjects because there is so much to tell, especially when you're experienced. And yes, we want more! Love
Absolutely the best reason for safety…”you don’t want to get blood on your workpiece” love it love it
Bloody good instruction video, no frills, just what is necessary. No daft introduction or self advertising. Spot on!
We need an entire “shop teacher” series at each major tool. This was awesome
I really like your 'teaching' style. Zero BS, direct, to the point and explicit.
Fantastic hands on teaching. I've been bandsawing for only 63 yrs and I still picked up one new trick from you today. Your shop cat is a wonderful Plus. We love him!
Jesus. You covered two mistakes I made that lead to serious injury. Thanks for mentoring those who simply don't know until they get hurt. 30 years on the bandsaw and your high siding workarounds taught me something. Good job.
Great video. No goofy music, no wasted time, just excellent advice with just the right amount of cat video sprinkled in.
Haha thank you! ❤
6:03
Yeah, he loves his cat, that's fer sher. :D
That was 19 minutes well spent on the best bandsaw lesson I’ve ever seen. Thank you for sharing your experience Sir!
Your bandsaw spoon video really made me so interested in woodworking when I was 13. Im now 21, and have an entire shop! You have no idea how much one video has influenced my life.
I thought that I was the master, but I bow to you. This is the most informative info I have ever seen on the bandsaw.
Thank you for the video.
Thank you! If the blade is sharp. It will be fine. If it’s dull I bring the guard down closer. To have more control… but I often keep it higher for more view
11:34 I'd hazard a guess that most shop saws have a much wider blade (.5" or higher) and they won't make the curve without the relief. Or they just don't trust the kids to cut without binding the blade.
@@derschwartzadder as a shop teacher, I can confirm that I don't want students binding the blade, I do try to keep two bandsaws with two different blades, a small one and a resaw one but kiddos aren't always mindful of which blade they're using so I could see enforcing relief cuts due to that. Also as the blade gets abused it's kerf is less wide and thus doesn't allow for tighter turns. Raising the guard up like jimmy does does help with blade maneuverability but again the teacher in me requires students to keep the guard down low in an effort to reduce injuries. Safer all around to have dumb facets on their piece that they can sand away with the spindle sander or disc sander. My rule of thumb is "if the curve is smaller than a coffee cup, use relief cuts. Also: shame on those shop teachers that don't make sure their machines are in safe working order, it's literally part of our job! (and kind of a fun one at that)
Awesome content! More videos regarding machine safety supplemented with pro tips and Diresta magic would be excellent.
Thanks for the video. Jimmy. I knew some of the tips but there were a lot that I did not know.Somebod you refreshed my memory and taught me a whole bunch period
For some, experience is the best teacher, but much can be learned from sharing dos and don'ts. I found most of what you shared from my experience, but found two steps very helpful. (e.g. sacrificial piece for zero clearance.)
All in all, very good vid.
Certainly do more like this. Power tools and hand tools are slowly becoming a lost art due to tech. So for posterity...
Not only are you a great teacher, but you do it with a sense of humour. Reminds me of my days in a metal shop, as a teacher. One of my favourite comments at end of a safety lesson was, "and remember,( I paused), you don't want to set yourself on fire".
Great tips, thanks.....
Some kid in my school shop caught on fire because he wasn’t wearing any protection other than his cotton shirt and his shirt caught a spark. He’s fine now
The one tip I use often that you didn't mention is that pulling material through the bandsaw is just as valid a method as pushing it through. So if you are cutting a straight or curved cut on a longer piece, start the cut by pushing the piece into the blade, then when you are halfway through the cut, with the piece fully supported by the table, walk around to the back of the saw and pull it the rest of the way through. This lets you support the workpiece throughout the cut and it will not want to tip upwards due to gravity
Very good tip. It’s way harder to cut yourself when pulling too.
That is a great tip ! Thanks for the insight...I did not think about doing that.
😢
I do the same method on the table saw
I have good outfeed support for the ts...so balance / tipping isn't as tricky. It also makes the walk to the other side longer.
I also worry about kickback when I let go of the piece...
But with smaller contractor saws, you can pretty easily walk around it without letting go, especially for sheet goods.
Bloody awesome! There's nothing more useful than learning from someone who has years and years of practical experience such as yourself!
I miss Spike. It was nice to see him in the videos back in the NYC days.
I agree with all the positive comments, great explanation of all the mistakes I’ve made! One additional thing I do, as you said, to back out of the cut, turn off the saw first. Sometimes I also, AFTER TURNING THE SAW OFF, I insert a small shim at the start of the cut, usually widens the whole cut to make it easier. Would also work with the saw running, but would be really dumb to be that lazy.
I miss this type of instructional video contest from you Jimmy. Takes me back to the NYC shop days.
Yes, there may be other videos available how to do something, but the community trust you and what you teach.
Keep on keeping on brother!
Dining table build videos are always appreciated.
I've been using band saws for a few years now and have learned a lot by trial and error. I appreciate all that you presented in this video and learned a few things that will deffinately serve me well. Thanks and best wishes for continued prosperity.
This isn’t a beginner’s video, it’s an everybody video. Well done!!
Being a shop teacher some 25 yrs now, using band saw on daily basis, I learned some new things.... Every day is a schoolday...
I don't know you but I was just wanna let you know how much I appreciate getting guidance from a complete stranger with 50 years of bandsaw experience. Thanks man
This is Just like your older videos. Even the cat looks the same. Love this style of video. Thanks for being such a great teacher
❤
Probably we need more of that “don’t do that it is not necessary” content
Заебись лишних пальцев много не бывает!!!!
😂 Yes please!
You can only say "No" to somebody, so many times. The real trick isn't to not turn the rejection of a premise into a challenge, but to have the idiot comply.
I hate cats!
Imagine if there was someone to stop you and say “don’t do this, it’s not necessary” at all relevant points in life. That would be a superpower
The BEST bandsaw use video I have seen with lots of common sense. I tend to trust guys who do videos who have all their fingers and fingertips. He admitted to being cut, who hasn't, but losing a finger shows some flaw in the user. Thank you very much.
Thanks Jimmy, lessons learned from decades of experience condensed into 20 minutes , this stuff is absolute gold 👍
Mr. Jimmy, I am 52 years old and I JUST got my FIRST band saw. I don't know (correction, didn't know) anything about it, until I watched your video. I STILL don't know anything about it, compared to you, but I definitely feel more prepared and informed having watched your very informational video. Thank you for sharing your considerable knowledge with all of us on the Internets! Shalom and happy Bandsawing!
I'm 63 and have been breathing sawdust since I was about 10. But I always love learning something new, and that's why I appreciate videos like these. One thing that I see a lot of (with a bandsaw) that concerns me is the distance between material and the upper blade guard. I was taught to adjust it to about 1/8" to 1/4", as that will not only reduce the chance of skin to blade contact, but reduces flex in the blade... sturdier blade equals less drift and deflection. But I'm always seeing people on TH-cam with 6" to 8" of clearance. Usually, these are the same ones who wear gloves at the table saw, so I consider the source, but I notice you -- who are vastly experienced -- also had a large clearance. I'd love to know your thoughts on the matter.
(Thanks for all you do)
Ditto
We’ll he said he takes a lot of risk I’m sure it’s so he can see better
100%, to me seeing the guide so much higher than the top of the workpiece, negated any confidence in the video.
@@stevemorris3710 Really, who has more experience on a Bandsaw that taught you ?
@@rrmerlin3402 Yes really. My Instructors. Hope that satisfies your curiosity. So glad for your fact-check lol.
EXCELLENT VIDEO! I’ve been bandsawing since I was 12 (I’m 62 now), and I gradually learned and applied all of these practices, especially after almost losing a thumb at 14). My dad was an artist who let us use all his machines, but there was ample training by him (esp. after my accident 48 years ago). I’ve not had one bandsaw accident since then.
So much great info here! Subscribed and will save this clip to show others.
Thank you! thank you!
Great tips and nice pest control officer. Keep up the inspiring work brother!
Jimmy, I've used a bandsaw for 25 years, and I can still learn a trick or two from you. One trick I have for you regarding cutting outside curves with a wide blade: I know you don't like relief cuts, but what I do is make relief cuts just shy of the cut line...about 1/16-1/8" from the line. Then when cutting the curve, I can do it in one smooth motion keeping the blade in the cut line while the wood bends and breaks away where I cut the reliefs. Works great without stressing the blade or creating the flats you mentioned in the video.
I love this type of video where you explain what you are doing and giving tips. I also love your cat in the videos, I miss Spike!
not only did this show how to work with a bandsaw safely, but also it gave me some great inspiration on what is possible with a bandsaw. Thank you 🤝
Amazing Jimmy. I’ve probably made all of those mistakes over the years. I honestly think this is one of your best videos you’ve made. Also, very cute cat.
I rate it THEE best. I've been watching Diresta since the very beginning
Thanks mate, I've been working in wood for over 50 years and i reckon the way you told the viewer how and why is perfect. No nonsense just practical.
Yes, to answer the question would I like more of these. FYI, I wholeheartedly concur about how dangerous those aggressive resaw blades can be. Bought a new 4tpi 3/4" blade back in January. Barely bumped it while installing it and adjust tension using the "flutter" method. It pulled my left hand right in. I'll never have full function of my left thumb or full strength in it again, but at least I still have it. It only takes a fraction of a second's loss of concentration. Thanks for the videos!
sheesh. ok, is it just the blade thats a problem? if a normal/safe blade snaps, does it whip around and cut you?
Oh my gosh that's awful! I caught my thumb in a tablesaw blade back in high school and I'm so glad I still have it, and really happy that it's still fully useable (still have a big scar but i can live with that.) I'm actually more afraid of my 16" bandsaw than I am of my tablesaw.
I just purchased a 14 inch band saw and kind of hate using it. After watching this video I was surprised how you hit on nearly every mistake I am making. This is a great video that gives me hope for future projects. Pencil is a great idea as a push stick. I worked in the ER for 30 years and have seen these take off a finger. Table saw was number one culprit in shop accidents.
This is fantastic - your confidence is based on years of experience, but I'm even more impressed with your ability to teach
PRICELESS......This should be required viewing in all HS shop classes as well as a DVD packed in with all new bandsaws. Thanks for the refresher course.
Thank you!
Your tips not only make work easier, but also increase safety. I look forward to more advice and explanations.
You probably have gotten this comment more times than you could read it but I would pay ANYTHING I could to apprentice at your shop. I am desperate to learn how to carve the way you do, and feel like I learn so much better by watching in person and doing by hand - and having someone there to be like "dont do that." In the meantime, I will watch everything you put up. Thank you, thank you, thank you.
@@artlargerthanme447 💪🏼💪🏼💪🏼💪🏼🙏🏼
I can wheel a chainsaw, use a chop saw like nothing else, handle a circular saw without a problem....I have a tabletop band saw from Craftsman that I'm scared to death of using. I do feel a little more confident now that I've watched this. Thank you Jimmy...yes, more videos like this. Someone mentioned a table saw.....that would be great! I have one of those, too, that I've used but still leary about cutting with it.
50 years and 10 fingers... quite an achievement !
Long time since I've used a band saw, but I just bought an old one a little while ago. I fixed it up and now she's ready to go and your tips have reinforced some old Tekneek's I used a long time ago. THANKS for helping to clear the cobwebs.
I love this! Yes, please make more of these types of videos. (Maybe a table saw one next? Or drill press?) Crazy how many of these things I’ve done or thought were a good idea. 😵💫 You are the best, Jimmy! 👊🏼 #DIRESTA
Yes table saw please 🤕
I’ll throw in my vote for angle grinder and belt sander
I agree, table saw next, then grinder, maybe drill press. This guy is a great teacher.
Find "Jimmy Tips" for tool-specific vids from way back.
What a refreshing informative video. Such a change from all to many TH-cam videos where the “how to” is in fact “ how not to”. They frighten me so much!
Very timely! I had a small (10") crappy bandsaw that always tipped and was frustrating to work with. One day it dropped and cracked and I went without one, but over time felt the need for one, so I am now close to finishing my own bandsaw based on Mathias Wandell's 16" model plans. Looking forward to being able to do what you do! (in about 50 years)
In my 50 years of woodworking, I have done only a minor amount of band sawing compared to using other tools to complete my projects. Your advice is the best. Knew of some by trial and error - still got all my fingers! and yes, only use a sharp blade. A community saw that I was to work with was hard to push and heat up and was told that I was working it too hard. I went a bought a new blade and put it on for just my project and the others in the shop wanted to know what I did. I told them and also told them that they should invest in their own blades. I took my own blade home with me.
Love this type of video! Reminds me of your older tool training vids. We can all use a drill, but it's awesome learning tips from someone with 6853256 hours of drill usage.
I thought I was the only one still using that antique Delta Milwaukee bandsaw! my wife found mine 25 years ago at a yard sale. I just made a fence for it today. I like your videos you tips will come in handy.
As one who recently acquired a bandsaw, this content was super useful and timing was fantastic. As always great video.
I have that same bandsaw, a 1948 14 inch Delta that my grandfather bought new. I've been using it since 1960. What a great machine. It is as old as me! In all these years, I have only been bit on the thumb ONCE. And believe me, it taught me a good lesson! Your tips are so spot on, I learned a few things too. You have gotten a subscribe and a thumbs up from me! Thanks for a common sense video.
Thank you Mr. Diresta for such amazing videos, i've been a long time subscribers now and it's been a long time since i've had the time to watch one of your videos. i'm starting to work with wood and those tutorials are amazing. It'd be great to have more videos like this one on different machines
great video, when i saw it on list I thought I don't need to watch that, I already now about bandsaws, then decided , oh all right i'll give it a minute.
Watched whole instruction, and I learned lot more than nine things, THANK YOU
Relief cuts are often necessary when removing material from inside of a curve while using a wide blade. And if they are not absolutely necessary they certainly make the task easier. With the wide blade, Jimmy just made a series of MANY small relief cuts. But without a doubt his method of doing it works well.
Students are hard on the equipment. They twist the blade and pull back on the wood when they cross their line. Relief cuts on an inside curve saves me from replacing snapped and kinked blades too often.
My first time watching. I am 62 and these are some of the best examples I have seen. You sir are a pro. Thanks for sharing your life long experience.
Bws
I'm the safety coordinator where I work. Several years ago, I was showing a novice 16 year old how to use a bandsaw. The very first thing I told him was never ever stick your fingers in the blade. I was very adamant about that and repeated it several times. He got halfway through his project, and what's he do, sticks his finger tip into the blade . It wasn't a bad cut, but his parents thought he should go to the emergency room. We spent 4 hours in the ER. I told him that little cut would probably be healed until you get to see a doctor. He got two stitches, and the away we went. My point is that when it comes to safety, listen to what you're told.
If you are in charge of safety and someone got hurt the first time they worked with the tool you were teaching them on then you are not doing your safety teaching job right.
Great video! I bought my first bandsaw about a year ago and since then I think I have made all 9 of your errors. Too bad I just found this video. You really are a talented craftsman and gifted teacher. Thank you.
Thanks for making most of this this video using a normal person’s bandsaw. Appreciated 🫡
Great tips, Jimmy, thanks. I saw a tip a few years ago that I incorporated as an experiment. It was helpful (or an illusion of helpful). Using a fine stone, diamond file, or steel file you simply dress the back of the blade, while it is running, to soften the hard edges. The theory is it reduces drag while doing curved cuts.
That is how I was taught 63 years ago and it does make a difference.
As a hobby carpenter, i find your advise is very good, and i try to follow it each time I use my very old "general" band saw! Also it does not have some of the adjustment capability that the more modern band saw has! I do a lot of adjusting by trail and error, so yes, your advise is most welcome when I'm preparing to do a little project, 'bird house - mantel clock - large & small lettering etc. keep doing what you are doing!
30-50 bandsaw tips in 3-5 minutes.
I did a double take-I have your saw, Delta/Milwaukee 14”, made in 1943. I know because I called Delta in Tennessee. The woman looked up the serial number, which was still in the files. I asked if they had a manual, which they do, so she sent me a copy. It’s hilarious to look at the prices of parts in 1943-bearings were like a buck and a half. Still working 80 years later.
Got it from a guy for $300, replaced the 3/4 HP motor with a 2 HP dust proof farm motor (for conveyors), and that saw won’t bog down.
I’ve been using it for over 30 years, and it’s one of my most used tools.
All these tips yet the most basic one is the blade upper guide. Which you dont use correctly 😅😅😅
He does use it correctly. His blade's still on just fine.
This is the best Video on TH-cam. I have seen so many folks with missing hands or digits it scares me to think about it... This video is TOPS for safety ! ! Thank you so much, BTW keep your Kitty indoors and safe, love that Kitty !! !
A little bit of humility and respect shown to others less skilled than you would go a long way?
Thank you. I've been woodworking for 50+ years. Not much in the bandsaw. Glad to say I learned a few great tricks today.
I know this video is over a year old but, thank you very much. Just got my first bandsaw (a older, used bench top model) a few days ago. I was really struggling with what I thought should have been simple cuts. When you showed the blade guides and bearings on your saw, I realized my saw was set up incorrectly. Now that I've corrected the setup issues, it cuts much better. Just need some more practice now lol. Thanks again.
I recently finished restoring a Tanner bandsaw made in Auckland New Zealand in 1952 and have been watching quite a few videos. This was the best one yet.Very helpful.Great vid. Especially the part about the upper guide setup and the pencil idea.
Great tips. I'm 66 and have been a woodworker for 40 years, and can still learn new things.
Well done. As a retired stair builder I have hundreds of hours on a bandsaw. Mostly resawing but also scroll type work, especially with making easements. I still get asked questions all the time about bandsaw usage. I will happily save this link and tell folks: watch this video!
Great video! The BEST tip I got was using the push stick to turn off the camera! LOL... seriously tho it is obvious your experience has superseded the books and many pros. Letting things fly on the how not to's is the best teaching anyone can give. It is always beyond a beginner's ability to grasp the physics of just how quickly things go wrong. Watching it makes them think much more clearly... and doesn't let them get to brave to quick.
My woodshop teacher did this (many years ago- before EVERYTHING had guards on it) with all the power tools. While he scared a few nerdy kids (with flying shtuff), everyone ended the year with all their fingers and all the bandaids stayed in the box. His table saw kickback lesson landed a 3 footer scrap across the shop , across his desk, and slammed his empty chair. Whereupon (without missing a beat) he proclaimed in a drill Sargent's manner if anyone did that they have failed woodshop haha.. Got a few laughs but it never happened. Thanks for sharing.
Superb video, I am a beginner woodworking self-learner, just bought a band saw and love it. Thanks for passing this wisdom and knowledge to us. With 50 years of experience, I think you should be standard for anyone making bandsaw videos. 😊
I've been using a bandsaw for 45 years but you can always learn! Love the pencil idea, I always just used a scrap but the eraser of the pencil is a great idea. Thank you!
I've been using a bandsaw for over 30 years & after watching your video, I'm surprised I have all my fingers! Super awesome info Thank You!
I've owned a bandsaw for 10 years and it's the one tool I really struggle with. This was a brilliantly helpful video - thank you. I will watch it again and start to implement some of your advice. My nemesis is trying to get straight even cuts whilst resawing to create thinner boards, I would be grateful for advice, guidance or a video even. Thanks again for sharing what you have learnt.
Just recently got.this bandsaw from my father's work. '75 rockwell 14". Mostly original equipment. Still.runs great. Had to replace the tires, balance the wheels and get new blades, what a solid saw.
Mr Diresta , you’re a jack of all trades. A very intelligent extremely talented and innovative and man. You now and then fabricate one of a kind off the wall high quality items . Many of these one of a kind off the wall items will overtime become very valuable collectors items.
Once a month I will binge watch all your TH-cam Channel Videos that I have not previously watched.
These are the best tips ever!!!!!! I don't think anyone has ever spoken of these tricks before.
I loved this and the amount of flinching I was doing watching you show what not to do tells me you're showing some important stuff. I also REALLY love this is your band saw from when you were 7. That's terrific!
Thanks for posting !
A couple of other tips I learned over my 30 years of amateur (very amateurish!) woodworking I give here for what it's worth.
1) Adjust the height of the blade with the height of the object, this way your blade will not wobble with a chance of breaking.
2) If someone watches you using the bandsaw they should never look at you from the side, but always in front or at the rear of the machine.
If the blade breaks if some part flies of it will do on the side thus hurting badly the person who's on the side. A very unlikely thing to happen… except that I saw it once 20 years ago.
These are onoy my two cents that I post because they are very easy to follow…
Again thanks for those sound advice …
Thank you. Great information. I have a Rockwell model 14 (28-240), excellent condition I picked it up at garage sale for $40. Best $40 I ever spent.
A real privilege to have this lesson from you.
Well I absolutely love this. It reminds me of the machinery I used to see around me in workshops as a child, young man. Almost always accompanied by the smell of oil. Thank you.
Thank you for all of the great tips, I will definitely use some in the future.
I just purchased a new bandsaw. I never used one before. Your helpful advice couldn't have come at a better time. Thank you.
Always good to learn new/different perspective... specially from someone very knowledgeable.
I recently had a friend over to cut his project... as I was about to say this is the safest machine in the shop...
Whoaa... blood spurts.
Can't attach photos... or I would.
(blood spattered on the floor, none on machine!, put the crime scene body cutout on floor)
With the dust collection system running it can be that you don't realize the saw is still running as you clear the table as the victim did. Not a deep cut, but he stopped at his DR office for an opinion.
It's something I coulda done...
So...
I constructed a circuit AC to DC to power a 10mm LED... and wired it into the saw... such that when the saw is on, a bright LED shines on the table top. Providing a visual reference .ITS ON..!!.
Thus far, 38 accident free days.
Felix
Thank you - good tips, clear illustration in use, clear English articulation and grammar (SO many fall down on this) and always to the point. A well-chosen speed of delivery meant that I could happily sit through the tips I knew already (as I knew they wouldn't take long) and at the same time, could just about keep up with the ones which were unfamiliar. Bravo!
Great info! I've been using bandsaws for over 50 years and I learned a couple of things. Thanks!
Thank you! I am just starting to use a band saw to cut blanks for bowls. Your suggestions were/are very helpful!😊
Awesome, thanks very much. I have a new Grizzly bandsaw and really respect it. I've been running chainsaw commercially for over 50 years and have all my fingers. When I demo 'd a different brand, the salesman almost lost some fingers when he tried to cut some white oak round wood that I brought to test the saw. Apparently he never watched video of do's and don'ts on bandsaws, so thanks again.
just finished fixing up a broken 10 in bandsaw, first of its kind in my shop and i’m so excited. great timing for this video for me,
thanks !
Great presentation, please make more. In a few minutes of watching your video I corrected several problems I've been having... kudos!
Great video! I just purchased a used Jet 14" bandsaw yesterday, and spent a couple hours setting it up. I should have watched this first, as I now realize I didn't set the bearing and guide blocks correctly. Thank you for the safety tips too, I'm a professional musician, and my fingers are my extra important to me!
Thank you for the tips and explanations, I’m a retired mechanic and as a carpenter, I’d make a good butcher.
I’ll watch you videos now to see what else I can learn, Ken from Australia.
I've been to lazy for years to buy a smaller blade for years and stuck with the technique you showed for tight curves with a larger blade, seeing how easy scroll cuts are for you with that small blade once I get home I'm ordering an assortment of different size blades because I think I will use the bandsaw more and to more of its potential, great video thank you
Jimmy, Thanks for the tips, tricks, & wisdom
Just bought my first bandsaw and my fingers can’t thank you enough for your sagely advice.
Thanks, I just got a small bandsaw and I'm going to make my wife a nice wooden spoon for Christmas! These are great tips.
Thanks a lot Ive never used a bandsaw and just got one, glad I found this video before I started.
THanks Jimmy. This has been the first of your videos that I've watched. I subscribed immediately , not because I need the advice as I am an old luthier who has run the same Italian bandsaw for forty two years now , but because you presented a well thought out no bullshit guide that will be valuable to a new user. I particularly endorse the whole body method for curves .Yes, calm and steady , Be the cut.
Thanks for the reminders - for me. I'm 72 and have been using shop machines since I was 13. Never an accident! (yet) I was taught that sharp is safe. A sharp blade or bit is so much safer. Respect the tool, let it do the cutting or drilling and love your body parts. Oh yeah - don't use your machines when tired or in a rush. My shop teacher said to think of cutting a stick of butter with a stick or a sharp knife. Great video - thanks again...
Good tips
I use a Shopsmith 11 inch
bandsaw and it works for me.
For the rip fence I use a 4 inch aluminum angle iron with welding vice grips on both ends to keep it straight.
You definitely know your bandsaw.
You should be a shop teacher.
Thanks
Thank you so much for the vid. We are opening a woodworking shop and (they) bought a bandsaw for it. Knowing the insurance company and the kind of people who will be using the shop I'm putting together a workshop for bandsaw beginners (and after doing so I'm gonna shit myself based on my tablesaw workshop and the hard-headedness of so-called experienced people). Your video helped me to order the subjects because there is so much to tell, especially when you're experienced. And yes, we want more! Love