@@Cskirt i do not, you can probably find one for three-phase motors on Amazon but for a single phase one i do not know, oh and if you do end up finding one, i definitely wanna see a bench grinder in there, those use induction motors too.
I did this expierement. Small 4 pole motor. Nominal speed is 1500 rpm on 50 hz. With vfd on 220 hz and 7000 rpm, torque so low. Rpm go down becouse motor cant spin its own blower
Lesson learnt: use steel brushes if you are overvolting your brushed mother. They lasted longer, just beware of the molten steel flying everywhere. :^)
Thank God, Finally the Video I Wanted Came. I Do These Kinds of Experiments All the Time. I Like Burning Small Engines. Where Did You Get the 400-500 Volt Supply? I'm Waiting for More Videos Like This
can anyone explain to me why the amps go up too when increasing the voltage? In electric cars, if I have a full battery, the motor gets more volts, less amps and with an almost empty battery the motor gets way less volts, but much more amps (at least for a short time until the BMS caps the amps drawn.) Cars with an 800 Volt system do use only half the amps as compared to the same model on an 400V system. But with half the Amps, the losses of the engine are only 1/4. But in all cases, the motor uses the same energy, but just adjusts amps to hold its target power / target rpm in comparison to the voltage available... Why the heck to all those tools spin until doom and just increase the amps drawn even if the voltage is risen?
The Saw Sounded like a Jet Engine Impact Wrench sounded like a 4 Stroke Engine and then Throttled up 9 in Grinder is not known what they sound like in overclocking the power Drills sounded like a Jet Engine (Same as the 1) Rotary tool is not known what they sound like
Böyle çektiğim videolar çok hoşuma❤ gidiyor ve çok beğeniyorum böyle videolar yapmaya devam etmeni istiyorum ve böylelikle daha iyi bir iki de izlenme ve beğeni alırsın ne olur böyle videolar çekmeye devam et🙏
A request: try overvolting a drone motor that spins at about 50000rpm at 3.7 volts, that motor is a tiny motor found inside of toy drones see if you can reach 100000rpm! Even if your meter says too high, still keep cranking up voltage until it gets damaged. Then post the link to the video.
I'm working on a video like that, I hope to release it in a month or so. I made an attempt a few videos back, it's called something like "Overvolting bldc motors/ pc parts" but my controller had trouble switching that fast. I got a much faster controller now to reach extreme speeds
![[#2024MAMA] BIGBANG (빅뱅) - 뱅뱅뱅 (BANG BANG BANG) + FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/EQsYfiPR9uM/mqdefault.jpg)
![[#2024MAMA] G-DRAGON - 무제(Untitled, 2014)+POWER+HOME SWEET HOME+뱅뱅뱅+FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/Ox29z5Nf1Uk/mqdefault.jpg)
I was expecting those angle grinder discs to fail and cause mayhem
i watched this with safety glasses on
i watched the grinder squinting like i always tend to do 😅
@@casemodder89 do you expect the blade just throwingn out of your device intno yor face
@@MrCoolOfficialYT a man who squints at angle grinders is a fool on all days except one
@MrCoolOfficialYT you literally wear safety glasses in your profile pic :^)
Those angle grinders made me really anxious.
Haven't had any accidents myself, BUT I keep thinking of it as ANKLE Grinder,
Because angle sounds like ankle (yikes).
here’s me watching motors die on a Thursday night with nothing else to do 😂
same how
Literally me right now.
This is wildly satisfying and cool to watch what happens at such absurd levels
The Biltema "dremel" tool DID make it's speced top speed....At 430 volts! LOL.
there was something not right about tha one. something dragging probably the bearings
It was 420 volts so 🌿
I thought the reader just looped around whenever it hit its top amount. Like it would actually be 130000 rpm
i want to see this with induction motors & a VFD, and incrementing the frequency until they burn up, that would be insanely funny.
Yeah that's on my to-do list, but it looks like I have to build my own VFD... Or do you have any suggestion on a suitable pre-built one?
@@Cskirt i do not, you can probably find one for three-phase motors on Amazon but for a single phase one i do not know, oh and if you do end up finding one, i definitely wanna see a bench grinder in there, those use induction motors too.
@@Cskirt They do exist, Zuked has them on Aliexpress. But only 2.2kw.
I've tried this but the electromagnetic field collapses around 3 a 4 times the frequency, so above like 160hz the motor only spins down
I did this expierement. Small 4 pole motor. Nominal speed is 1500 rpm on 50 hz. With vfd on 220 hz and 7000 rpm, torque so low. Rpm go down becouse motor cant spin its own blower
230mm grinder accelerated to a speed of ~650 km/h ☠️🌚
The cutting wheels seem to have a much better tolerance beyond their ranges than the grinders 😂
Man seeing those grinder discs spin like that made me have flashbacks of when one exploded on me
Must have been an expensive video to make 😶
All my videos are expensive 😅, this wasn't too bad, mostly old used corded tools no one wants
@@CskirtAre you from scandinavia? I recognized the Biltema logo :o
@@kraəb it literally says Sweden when you click on the channel description.
@@VIPPotato Oh, well i didn't see that. Thanks!
In the day and age of lithium and brushless tools, you can often find corded tools in the trash or at the flea market for a couple bucks per lol.
Getting into Photonicinduction territory, I see.
I wish photonicinduction was still active 😢
Holy moly that impact gave me welders flash😂
Same
Lesson learnt: use steel brushes if you are overvolting your brushed mother. They lasted longer, just beware of the molten steel flying everywhere. :^)
I think I just found me my new favorite .I like it. it's amazing how tough they actually are
4:09 make a wish! Happy birthday to you! 😅
I knew exactly what to expect with the steel "brush" on that impact but still gagged when I heard that startup
When you were testing out the Black and Decker and DeWalt angle grinders, I was expecting them to surpass their exceeded limits, and they sure did.
That DeWalt was especially impressive wow.
Need to do it again but with brushless power tools
Imagine drilling materials at 30.000rpm
You'll probably drill a concrete in like 1 second
Photonicinduction would be so proud :D
If he'll be ever back
That circular saw looked like it hit 88 mph!
The flux capacitor was going strong with these tools... They'll wonder where all the power tools came from back in 1955.
1:25 The 1.9 PD TDI in the work van on a cold winter morning..
Well that settles it- I’m upgrading all of my corded tools to steel brushes
These power tools are universal motor can run at DC and burnout way more powerful! I recommand try this next time!
The impact wrench became a jackhammer 😂
7:19 V8 POWER BABY
Awesome video! Subscribed
this guy's neighbors must love him
Thank God, Finally the Video I Wanted Came. I Do These Kinds of Experiments All the Time. I Like Burning Small Engines. Where Did You Get the 400-500 Volt Supply? I'm Waiting for More Videos Like This
I bought it used, 3-phase variable transformer with overdrive
Good god that’s some serious voltage
6:19 I’ve seen car engines fail less violently than that angle grinder. Holy fuck
bro the angle grinders caused me anxiety and i wasn't even remotely close to them
443V to fail that old school saw, old tools were incredible lol
Pneumatic tools can do that type of rpm all day long 😎
Awesome! Keep up the good work! 😊
Just FYI that grinder wheel was going 226 MPH 🤯
That's fine, battlebots are allowed up to 250mph tip speeds
3:20 holy shii that needs an epeleptic warning😂
Nihayet gelebildin😍 uzun zamandır video çekmiyordu İnşallah en kısa sürede kanalında yeni videolarda görmüş oluruz Sevgilerimle❤ sana iletiyorum
Rotary tool: **says 35k rpm**
Also rotary tool: **barely can handle the 35k rpm**
It made one last attempt and hit 35k before popping. That's how they rated it lol
@RennieAsh 🤣
I put my face shield on watching this at 4:34
I was scared that the circular saw was going to fly out.
Missed opportunity to hit those grinders with ammer.
1:36 started sounding like a diesel engine or something like that
😂😂
That’s true, it did
2 stroke lawnmower
Awesome video
Next *Makita Mitre Saw Ls1040*
1:30 Starting Up
6:28 very thanks!!
What power company you got there? Mine got my TV, speakers, PC PSU, washing machine and water heater shot after releasing three-phase current
6:02 the jet engine is starting up
5:20 thanks ❤❤❤
?
5:43 sounds like a supercharger
The motors with lights out @@ be cool
The motor:💥🥵☠️
Good vídeo!!!🎉
Just a idea: try overvolting cheap kitchen ware😂 like blenders and dough machine's or water cookers😮
He did tho
Bro's making mini tokamaks at home
Why mans live so short?
Mans:
Good old "Meec" tools.....
Bro tryna create time machine
all gas no brakes
What kind of power supply are you using to blow these things up!?
Your check motor lights are on
Did the commutator explode on the black and decker grinder?
Aww popped iiittt!
can anyone explain to me why the amps go up too when increasing the voltage?
In electric cars, if I have a full battery, the motor gets more volts, less amps and with an almost empty battery the motor gets way less volts, but much more amps (at least for a short time until the BMS caps the amps drawn.)
Cars with an 800 Volt system do use only half the amps as compared to the same model on an 400V system. But with half the Amps, the losses of the engine are only 1/4.
But in all cases, the motor uses the same energy, but just adjusts amps to hold its target power / target rpm in comparison to the voltage available...
Why the heck to all those tools spin until doom and just increase the amps drawn even if the voltage is risen?
Biltema 💪🏻💪🏻😂😂😂
i dont really know why but its seems so brutal.. i feel bad for these instruments..😢
Lets go a new video!
3:31 AAAHH (MY EARS IS BROKEN)
What you had a biltema powertool are you uropean?
Yes, swedish
The Saw Sounded like a Jet Engine
Impact Wrench sounded like a 4 Stroke Engine and then Throttled up
9 in Grinder is not known what they sound like in overclocking the power
Drills sounded like a Jet Engine (Same as the 1)
Rotary tool is not known what they sound like
Planning *welding machines*
Warning! Harsh Sounds! -> Shows Ultra Epilepsy Gore Video
1:35 a generator?
this sounds like 2 stroke engine 7:50
AM NOT LYING
Jet engine
i like my tools sparky bro
The 2nd one 😂
Warning:Don't try this at home
Ok, I will.
Can you blow some halloween toys please?
Woah
I have full battery after watching this video
pls do more
Can you overvolt vacuum cleaners next?
He already did two vacuum motors tho
I’m curious but it also feels wasteful and sad.
Böyle çektiğim videolar çok hoşuma❤ gidiyor ve çok beğeniyorum böyle videolar yapmaya devam etmeni istiyorum ve böylelikle daha iyi bir iki de izlenme ve beğeni alırsın ne olur böyle videolar çekmeye devam et🙏
The angle grinder exploded, or atleast the sparks look like it
Your back after 1 month
Yeah, been busy lately, but I hope to release a few different videos over the next weeks
@@Cskirt oh ok
Love it, but i suggest a photosensitivity warning before the video starts.
A request: try overvolting a drone motor that spins at about 50000rpm at 3.7 volts, that motor is a tiny motor found inside of toy drones see if you can reach 100000rpm! Even if your meter says too high, still keep cranking up voltage until it gets damaged. Then post the link to the video.
I'm working on a video like that, I hope to release it in a month or so. I made an attempt a few videos back, it's called something like "Overvolting bldc motors/ pc parts" but my controller had trouble switching that fast. I got a much faster controller now to reach extreme speeds
Lol silly and fun
Should have also measured the rpm increase
lucky that the saw blade didnt rip itself apart, coulda been deadly if it did
the impact wrench turned into a lawn mower, then into a jet xd
5:10 he made a new star in the solar system 💀
That was made out of metal, no way that could pop. At least at the rpm the saw gave.
Dc motors in 220v Ac
More like 440v
2:11 7660w ac
wow
Next episode: Blowing up different fuse☑️
I'll recommend blow a big capacitor, he did though.
next video , put the tool in a bucket of liqued nitrogen... then see how far you can push those tools
Liquid*
Hydrogen*
😂😂😂😂😂
UK ?
Sweden
Second
First