Is there any advantage to this implementation vs the standard ELRS that most people use? ELRS is LORA, on an Arduino-compatiblr ESP32 board. The same thing but FAR more advanced. It looks like this implementation is like ELRS, except slower, heavier, more expensive, and less reliable? Any reason to re-invent ELRS, but worse?
Good afternoon, I ask for your help. According to your example, I tried to pass 4 values, and not 2 as in your example. But I encountered a problem in the receiver.
no because lora can transfer very limited data (like 64 byte, 128byte) you need much more data to transfer sound.if you use lora for walkie talkie or a camera you need to wait for hours to be able to tranfer large data.
Hi I implemented the code on a card with Lora but every time I activate the motors with a l298 bridge the arduino nano freezes and I have to restart with the rst button on the arduino why does this happen
@@ElectroniClinic Ok thanks for the answer, that was the first thing I did, I checked the input voltage to the Arduino, it is 8vdc y puse un watchdog pero a un así se queda congelado esto ocurre cuando hago avance o retroceso
@@ElectroniClinic It was the first thing I checked, the voltage is 8 vcd, it is connected to Vin and the LorAx is connected to the 3.3 vcd of the arduino, and it even has a 470micro capacitor in Vin and I put a watchdog, it follows the problemI have already changed the Arduino nano to rule out a hardware failure, it still only happens when I move forward and backward, that's when the Arduino freezes. Could it be something else?
GREAT JOB!! THE NEXT STEP IS TO ADD SENSORS ON RC HELICOPTER AND COMPLETE AND FULL LORA SERIES...THANKS IN ADVANCE!
Great content indeed! Inspiring and entertaining!
Is there any advantage to this implementation vs the standard ELRS that most people use? ELRS is LORA, on an Arduino-compatiblr ESP32 board. The same thing but FAR more advanced.
It looks like this implementation is like ELRS, except slower, heavier, more expensive, and less reliable?
Any reason to re-invent ELRS, but worse?
What is delay in ms?
I use Lora for remote control, it delays about 1sec, so i think it is not suitable for remote control. It is so lagggg
Good afternoon, I ask for your help. According to your example, I tried to pass 4 values, and not 2 as in your example. But I encountered a problem in the receiver.
i have a question, if i follow the circuit diagram, the reset button does not connect to anything. will this still work ?
thank you so muchhh! im making an rc car and this works so well!
Why not just use express LRS?
Very great
Bro can you make 6ch code for this transmitter and raciver
Just beautiful. I would like to be able to reach out to you for some projects
Sure.
I want to try with ESPNow at first and it's a long journey.
Great content sir...🎉 sir plz make 8 channel tx rx...with lora..
Ok sure I will, I will cover this in flight controller designing.
Do you need a HAM radio license to operate LoRA?
no, it's an open band, low-power transciever
Pensando aqui , 1 controle de drone de longo alcance 10 km que preciso de 4 ch ou mais vai ser muito complicado 😢
Hey, could you create a walkie-talkie using this Lora module?
no because lora can transfer very limited data (like 64 byte, 128byte) you need much more data to transfer sound.if you use lora for walkie talkie or a camera you need to wait for hours to be able to tranfer large data.
Hi I implemented the code on a card with Lora but every time I activate the motors with a l298 bridge the arduino nano freezes and I have to restart with the rst button on the arduino why does this happen
@@Ekirnet-one check your power supply and also use a watchdog timer.
@@ElectroniClinic Ok thanks for the answer, that was the first thing I did, I checked the input voltage to the Arduino, it is 8vdc y puse un watchdog pero a un así se queda congelado esto ocurre cuando hago avance o retroceso
@@ElectroniClinic It was the first thing I checked, the voltage is 8 vcd, it is connected to Vin and the LorAx is connected to the 3.3 vcd of the arduino, and it even has a 470micro capacitor in Vin and I put a watchdog, it follows the problemI have already changed the Arduino nano to rule out a hardware failure, it still only happens when I move forward and backward, that's when the Arduino freezes. Could it be something else?
Going in the right direction,
Towards lora mesh network
FHSS?
ভাই আমি 99টাকার পেকেজ চাই
مرحبا بك صديقي ممكن رقم وتساب توصل معك