Just short clip of my bigfoot with all the new parts and fun stuff on it! Goped, Go, ped, GSR, big, foot, bigfoot, ADA, S2, pipe, Exhaust, .800, spindle
@frenchy27 thanks man and the cables goes from this little piece on the frame to the dead center of the engine like in the middle between the carb and the pull starter.
@aooskvarek thanks man i appreciate the comment! its a pretty sweet biggie it was my first build i have ever done on a goped, i endded up adding alot more stuff on it, it was cherry when i was done :).
nice bigfoot if i were u i would toss the 2 bolt top end and crankcase and upgrade to a 4 bolt a 2 bolt motor will always blow a gasket over time especially when modified (pipe porting Etc...) my super x ped blew a head gasket and i tossed the 2 bolt when it seized and upgraded to a 4 bolt reed case from OBR (oneill brothers racing) check out OBR's website and look at their long block engines they're a complete motor minus the ignition fan covers and flywheel and pull starter cover hope i helped
that could be the problem. i would try getting a innertube with a straight valve stem. alot of the stems are L bent and i had the same problem on mine. for great parts check out DDMmotors or daves discount motors online its a great site thats has everything
with the .800 spindle does it do well on hills because I need I new one but there is hills around I would like to go up so I either get a .750 or .800 black magic spindle any suggestions
HELP!! i dont know why but all the time i put and new inner tube in the back tire it keeps tearing up and loosing air. i even put a new back tire thinking the old one had holes but it didnt. even with the new back tire the inner tubes end up loosing air some how. when i ride it or push it i notice the stem where you put air in keeps hitting the gas tank and fender holder, can this be the problem? if so please replay on how to fix the problem
no its not to bad it takes about 20mins total to remove the old one, and some muscling to get on the new one.
@frenchy27 thanks man and the cables goes from this little piece on the frame to the dead center of the engine like in the middle between the carb and the pull starter.
@aooskvarek thanks man i appreciate the comment! its a pretty sweet biggie it was my first build i have ever done on a goped, i endded up adding alot more stuff on it, it was cherry when i was done :).
sweet man , I love it !
@pocketbike1010 its a ADA S2 Race exhaust :)
nice bigfoot if i were u i would toss the 2 bolt top end and crankcase and upgrade to a 4 bolt a 2 bolt motor will always blow a gasket over time especially when modified (pipe porting Etc...) my super x ped blew a head gasket and i tossed the 2 bolt when it seized and upgraded to a 4 bolt reed case from OBR (oneill brothers racing) check out OBR's website and look at their long block engines they're a complete motor minus the ignition fan covers and flywheel and pull starter cover hope i helped
@mastax1234 hahah i totally understand what you mean and its strictly for looks, to give it a sleek look!
that could be the problem. i would try getting a innertube with a straight valve stem. alot of the stems are L bent and i had the same problem on mine. for great parts check out DDMmotors or daves discount motors online its a great site thats has everything
@yourmom922 thanks jimmy! and if i did do a drive by on my uphill street it would look like i was going about as fast as a snail hahah! i will tho
Could you make a video on how to install a clutch cable on a Go-ped bigfoot If you could that would be great thanks
sweet.
Got mine to go 25/26 with an LH
can you please make a video on how to replace or put in a new one?
i dont get it, whats the purpose of the gas tank cover? then you wont know how much gas you have left in your tank?
with the .800 spindle does it do well on hills because I need I new one but there is hills around I would like to go up so I either get a .750 or .800 black magic spindle any suggestions
I was thinking about getting a goped, how good are they at hill climbing? and with a stock goped bigfoot I should get ~20mph, right?
@2008yz250f4ever , do you still have the bigfoot gsr frameand motor mount for sale/trade?
HELP!! i dont know why but all the time i put and new inner tube in the back tire it keeps tearing up and loosing air. i even put a new back tire thinking the old one had holes but it didnt. even with the new back tire the inner tubes end up loosing air some how. when i ride it or push it i notice the stem where you put air in keeps hitting the gas tank and fender holder, can this be the problem? if so please replay on how to fix the problem
is it hard to replace the tilt cable?
looks sick! u gonna do a drive by video? hahaha
it looked nice until i saw it was a friction and not a chain goped
Can i ask how much was it? the Goped alone.