Is it a step down voltage controller?? Can we give 18v in input and get 1.5v to 15v in output?? what about its heating issue or heating time on using??
Is it ok to plug the plug the pins of into a mosfet into a 3 terminal male plug? The spacing between the 3 square holes on the plug is exactly the same on the IRFZ44N. I’ve never bought any electronic components and I source all my stuff from the dumpster. I only have one IRFZ44N mosfet and I already know how easy it is to break the pins off them. I feel like plugging it into a plug with several inches of wire will alllow me to use it for other things too and not make it as permanent. Does anyone else do this? I also realized I can plug them into those 8 pin cradles(?) that you push an dip8 ic into. It works sorta like a mini breadboard in a way.
Питание от мощного трансформатора 18-22 в через мостик 10а , поставив транзистор на радиатор можно сделать зарядное для авто!
Much more clearly if u put circuit diagram on video or make blog for your project, tx u mr 🙏
useful video agar sircuit diagram hota aur bhi acchha hota
Is it a step down voltage controller?? Can we give 18v in input and get 1.5v to 15v in output?? what about its heating issue or heating time on using??
Input max 55v.
If u want more than 5A then use a bigger heatsink
@@TARIQLAB really thanks for your reply, you make great videos 🙏
Is it ok to plug the plug the pins of into a mosfet into a 3 terminal male plug? The spacing between the 3 square holes on the plug is exactly the same on the IRFZ44N. I’ve never bought any electronic components and I source all my stuff from the dumpster. I only have one IRFZ44N mosfet and I already know how easy it is to break the pins off them. I feel like plugging it into a plug with several inches of wire will alllow me to use it for other things too and not make it as permanent. Does anyone else do this? I also realized I can plug them into those 8 pin cradles(?) that you push an dip8 ic into. It works sorta like a mini breadboard in a way.
okay thanks but please tell the names of following things use in the circut .
All Components clearly mentioned in the video
Muje 68.v par cutoff circuit chaheay kia ye kam Kare ga input mere pas 74 volt 4 amps hain
U can use transistor J13009 400v 12A
@@TARIQLAB circuit diagram?
عزيزى بعد التحيه الدخول كام فولت واشكرك
50 v
Ye kinay ampar ka load Le sakti hain
49A
Why not blust bulb on 48v ???
Bulb voltage?
60v bulb
Всегда прилагай схемы--а это одни твои руки
Kia ye 60+ volts pe kam kare gi
No....50 se 55 volts tak
60v tak karey ga, Potentiometer ziyada value ka laga lena
y el diagrama?
What's maximum out put Amp.?
50v
Current? Not volt
@@lukachstrimer7212 current? Not volt
It wwill burn after 15 min. On 2 amp.
He made just a resistor 😂
Hi bro
48v bulb ampere how much?
1A
Sir,35volt 2ampere load will work fine with normal heating?
If need use bigger heatsink
Its maximum output current with normal heatsink and I can use capacitor on input and output
10 A, capacitor no need
@@TARIQLAB I want to desgin for sinewave UPS when I make 24v/48v ups when we need a buck converter maximum 2 amp
Jo sinewave kit k sath ata wo bht heat hota ur burn ho jata ha wo adjustable ni hota
Input voltage and ah not informed.
Input 50v max 60v, 20A
Çok küçük olduğu için iyi anlaşılmıyor