If your old one isn’t already spoken for, take the compressor off your old one and tie the old tank into your new compressor. That’ll give you 140 gallons of capacity, or you could set it up like a surge tank. Either way will give you more air than you could ever need!
Ur reaction was So funny where u got scared wen the tire popped into place while filling it. I had to watch its multiple times. Nice job on the sweet truck. Lovin the new meat
I’m gonna need a review on the ingersol compressor after a while as I too am looking to upgrade soon when my husky 60 grenades & it will as it’s 12 years old with a lot of hard use. Thanks brother
Austin you need to get a two stage compressor instead of a single stage, recovery is much faster and keep's up with high CFM tools like your blast cabinet. Linking the old tank to the new one will also work for high volume to. Another great vid keep up the good work.
Hm, not much power? Check the carburator jets. Might be small. Also check the "auto-advance" of the spark plugs if it s working properly. Check the valve clearance (as you mentioned) too. Just some thoughts.
I bought the 60 gallon Ingersoll in 2019 and my auto switch already went out. The contact welded themselves together and wouldn't shunt off at max psi. So after I replaced it I always pull the power when I'm not in the shop. I need to go through my system to look for the slow leak that caused it to run more than it should. Just a few thoughts. Keep up the good work!
I’d like to see how that thing pushes snow. I may have to get one of these if I can find it at a fair price. Thanks for buying American on the air compressor.
Great skills and attention to detail as always Austin! Glad to see the fire is on there as it means its summer here in New Zealand Haha! Look forward to your videos mate!
If it hits a wall at 40, it could be a governor. It does so well at low speeds and even high revs. I know the newer ones I used on street for work were governed to 25mph, so right in that ballpark.
I noticed the wheel studs stuck out beyond the spacer, was there clearance on the back side of the rim? I ran into that trying to put 1" spacers on my sons 97 T4R, had to go with 1.25" thick spacers to get it to work. That thing is really cool!
I saw that as well. It looks like there's enough thread engagement that the original studs could be cut down flush for a better fit. As it is, it appears that the wheel is touching the ends of the old studs and not the face of the hub/spacer.
Hey , just a question , I have a 1990 Suzuki carry in bc Canada and it’s street legal, everywhere I look nothing says the tires are DOT , are they stamped ?
Now that bead breaker tool you made is way overkill! Lol. You could break beads on semi's (tractor trailers) You should combine those two air tanks to increase your air storage too. Great content as usual. Cheers from Sydney Australia 🇭🇲👍🦘🦘👍🇭🇲🇺🇸🇺🇸
Another great upgrade! What tires did you get? I have 4 older VW GTI 14x6 rims for my Carry ( they fit perfect) I don’t have a Clear choice for DOT off-road tires.
Those IR compressors come with anti-vibration isolation pads and hardware. I mounted mine to a modified hand truck with inflatable tires and a thick, rubber isolator. It produces very little harmonic resonance. Surprisingly quiet.
Maybe you could build a custom Ladder Rack like Mike Festiva for your kei truck and hold or mount two spare wheels/tires in the rear for extra weight back there! I’m also still hoping you put a different engine in it one day lol, 3 cylinders just isn’t enough.
I know it is a bit of a older video, however I have a quick question. Is that the TS4N5 two stage 80gal. air compressor from Tractor Supply? I am thinking about going out to Deer Park next time I am in Spokane and picking one up and would welcome some feedback after almost two years of ownership. Would you buy it again?
Not sure how much bigger then standed them tyres are but if the are bigger I'd be looking at taller diff gears if they're available for these things???
Man I am still so impressed w your skill level and ingenuity when it comes to all things automotive. Do you plan to paint (or use bed liner) this truck or leave it as is?
That little truck should go through anything it clears with those claws on it! I was noticing your hardware bin. Did you just go into a hardware store and pick everything or did you find a place that offers kind of a basic hardware package? Anyone else feel free to let me know if such a thing exists :o)
I know big big tires really take a lot of power from these things, also Japanese low grade is about American mid grade, so probably try mid or high grade fuel
When it comes to Air ...SCFM rules... and Max Air Pressure is secondary.... you need as much SCFM as you can afford and the Highest Air Pressure next....then your Tank size will dictate how often your compressor has to come on to Keep Up with your biggest demanding air tools....anything running constantly will drain your system.... and yep..your Blaster is going to still need a break between work... 30 SCFM and 80 - 100 gal tanks at 150-175 PSI will be the best you get without going crazy expensive to get a full commercial shop sized compressor... all depends on your budget and needs...
Man I like your projects but what's up with the headlights are you going to go with LEDs for headlights, and keep up the good work, I like your show and I'll catch ya on the next one.
i think you need to go watch motocheez channel and see what he did with his carb and how he added a supercharger to his kei truck,, its a diahatsu hijet, but its pretty similar
![NISAMANEE - TADA (ท้าดา) [ OFFICIAL MV ]](http://i.ytimg.com/vi/hcQHEPMmJpU/mqdefault.jpg)
If your old one isn’t already spoken for, take the compressor off your old one and tie the old tank into your new compressor. That’ll give you 140 gallons of capacity, or you could set it up like a surge tank. Either way will give you more air than you could ever need!
Hell yeah first comment. Over 20 years doing tire work and I still jump when seating tires when they pop.
Same here haha
Austin, you and Mike Festiva need to have a Mini Truck rally!!! Keep up the sweet work!!
Your fabricating skills are bar none.this thing has come a long way in short time.good job,keep up the great work.😎😎😎👍👍👍
Thanks!!
Ur reaction was So funny where u got scared wen the tire popped into place while filling it. I had to watch its multiple times. Nice job on the sweet truck. Lovin the new meat
I love it when a plan comes together, the A-Team
Great tool idea with the press to been the tire beads! Like the new compressor! Should do what you want now!
I’m gonna need a review on the ingersol compressor after a while as I too am looking to upgrade soon when my husky 60 grenades & it will as it’s 12 years old with a lot of hard use. Thanks brother
Austin you need to get a two stage compressor instead of a single stage, recovery is much faster and keep's up with high CFM tools like your blast cabinet. Linking the old tank to the new one will also work for high volume to. Another great vid keep up the good work.
We had one at the weld shop great little hauler. Nice job on taking to it really like how you take a truck and go to the extreme with it.
Hm, not much power?
Check the carburator jets. Might be small.
Also check the "auto-advance" of the spark plugs if it s working properly.
Check the valve clearance (as you mentioned) too.
Just some thoughts.
I bought the 60 gallon Ingersoll in 2019 and my auto switch already went out. The contact welded themselves together and wouldn't shunt off at max psi. So after I replaced it I always pull the power when I'm not in the shop. I need to go through my system to look for the slow leak that caused it to run more than it should. Just a few thoughts. Keep up the good work!
I’d like to see how that thing pushes snow. I may have to get one of these if I can find it at a fair price. Thanks for buying American on the air compressor.
Really nice mini truck ! I love it ! 👏👍
Great skills and attention to detail as always Austin! Glad to see the fire is on there as it means its summer here in New Zealand Haha! Look forward to your videos mate!
I wish you good luck and success always bro
It seems the link to the tires no longer works, just curious what the wheel/tire combo is? Thanks, great looking truck dude!
If it hits a wall at 40, it could be a governor. It does so well at low speeds and even high revs. I know the newer ones I used on street for work were governed to 25mph, so right in that ballpark.
Little truck is looking good.
fun fact is that Żuk is a car that was produced in Poland in 1958-1995. In english Żuk means beetle =)
That compressor is the same we have in our shop and it’ll run a plasma and a air dermal tool almost steady
At the same time
Gotta admit, i was cracking up when u jumped when the tire bead popped lol
Haha it always gets me
Charcoal gray raptor liner and it will look good
I noticed the wheel studs stuck out beyond the spacer, was there clearance on the back side of the rim? I ran into that trying to put 1" spacers on my sons 97 T4R, had to go with 1.25" thick spacers to get it to work. That thing is really cool!
I saw that as well. It looks like there's enough thread engagement that the original studs could be cut down flush for a better fit. As it is, it appears that the wheel is touching the ends of the old studs and not the face of the hub/spacer.
Thanks! Yes there is room on the mating surface of the wheel!!
Hey , just a question , I have a 1990 Suzuki carry in bc Canada and it’s street legal, everywhere I look nothing says the tires are DOT , are they stamped ?
Nice welds! You see this motocheeze this is a weld
Now that bead breaker tool you made is way overkill!
Lol. You could break beads on semi's (tractor trailers)
You should combine those two air tanks to increase your air storage too.
Great content as usual.
Cheers from Sydney Australia
🇭🇲👍🦘🦘👍🇭🇲🇺🇸🇺🇸
Another great job! I am amazed on your different skills.
Ever think about selling t-shirts on this project and the red Toyota?
New motor 👌🏼
Another great upgrade! What tires did you get?
I have 4 older VW GTI 14x6 rims for my Carry ( they fit perfect) I don’t have a
Clear choice for DOT off-road tires.
It may not be fast but it looks cool.
I would have left the compressor on the pallet it came with to absorb vibration but hey to each his own. As usual nice work.
My 7.5hp 80gal came with 4 thick rubber pads.
Those IR compressors come with anti-vibration isolation pads and hardware. I mounted mine to a modified hand truck with inflatable tires and a thick, rubber isolator. It produces very little harmonic resonance. Surprisingly quiet.
Ok didn’t see them the way he swayed the compressor back against the wall. He would have torn them up moving it like that.
Still think you should fab a turbo setup on it !
Great video and very informative
Love the video. I have the same truck what rim and tires you put on I went to link but says not available. Also what lift you have on it 😀
Maybe you could build a custom Ladder Rack like Mike Festiva for your kei truck and hold or mount two spare wheels/tires in the rear for extra weight back there! I’m also still hoping you put a different engine in it one day lol, 3 cylinders just isn’t enough.
Honda D series, Subaru Flat4, Toyota 4banger, or maybe even a Rotary?? 😂👀
Well you do like diesel conversion find a kubota 3 cid and do it
Motocheeze put a super charger on his from a Subaru I think, it really increases the profromance for climbing the hills
i`m an electrician ! that compressor jut needs # 10 wirw and a 30 amp breaker ! no problem !
I giggle every time you jump inflating tyres. You know its gunna happen Ya just can’t help but jump!!🤣
Filter dryer should be at least 10 ft from the compressor for best results
What size tires and wheels are you using? Your eBay link doesn't work! Nice rig, great job!
Are you sure its powerful enough to plow snow? The tires will definitely help it though!
Low gear it will be fine!
I like your shop. First. Class
I know it is a bit of a older video, however I have a quick question. Is that the TS4N5 two stage 80gal. air compressor from Tractor Supply? I am thinking about going out to Deer Park next time I am in Spokane and picking one up and would welcome some feedback after almost two years of ownership. Would you buy it again?
What size are those tires? The website link does not show them.
Check your timing. Advance it to 10 degrees.
Check valve lashing for spec. If you need those numbers I can provide that as well.
Will do! You have the valve clearance spec?
Not sure how much bigger then standed them tyres are but if the are bigger I'd be looking at taller diff gears if they're available for these things???
Hey Austin can you make a 3rd gen rear bumper?
what is the size of your tire and also the rim? i have also a multicab.ty
Man I am still so impressed w your skill level and ingenuity when it comes to all things automotive.
Do you plan to paint (or use bed liner) this truck or leave it as is?
Thanks! I haven’t decided on paint yet!
What about the Tacoma? When are we going to see the rest of the buid?
What are the tires called and size? The link you left does not work anymore.
That little truck should go through anything it clears with those claws on it! I was noticing your hardware bin. Did you just go into a hardware store and pick everything or did you find a place that offers kind of a basic hardware package? Anyone else feel free to let me know if such a thing exists :o)
I used to part out dirt bikes so most of my hardware is from that!
If you dont sell your old compressor you can tie it in as an extra volume bottle
Do they not make those tires anymore? Link is not working anymore
I know big big tires really take a lot of power from these things, also Japanese low grade is about American mid grade, so probably try mid or high grade fuel
That thing would be pretty cool solid-axle swap with some Suzuki Samurai axles or something
needs more power to run that...
How fast did you think it was going to go. Put a vw motor in it
Mike Festiva has a channel and some videos of him going through his Carry's engine issues. might be worth a look.
Here’s a question … Tell us, in a video, what the man who can fabricate anything, can tear down and rebuild any vehicle want for Christmas?
More TOOL'S and 💰 🤑 lol
When it comes to Air ...SCFM rules...
and Max Air Pressure is secondary....
you need as much SCFM as you can afford and the Highest Air Pressure next....then your Tank size will dictate how often your compressor has to come on to Keep Up with your biggest demanding air tools....anything running constantly will drain your system.... and yep..your Blaster is going to still need a break between work... 30 SCFM and 80 - 100 gal tanks at 150-175 PSI will be the best you get without going crazy expensive to get a full commercial shop sized compressor... all depends on your budget and needs...
Be really cool to turbo charge it. Think about it.
Man I like your projects but what's up with the headlights are you going to go with LEDs for headlights, and keep up the good work, I like your show and I'll catch ya on the next one.
How are the balance on the tires?
You do not need to balance the tires?
What size and brand tire did you put on this thing, The link is expired
i would be looking at small diesel engines to swap into it....like a Yanmar or Kubota from a tractor... 3 cylinder ??
Looked on e bay did not see Tyres, so can you please send me the Tyre name and part number. Thanks for your time!
Just remember for every inch over stock you go up on tires your speedo is gonna read about 3 miles slow.
I would love for you to fabricate a front and rear bumper for my 1990 Carry Truck! Let me know a price and how to contact you for order.
Put a plastic tank in the back , easy to move and fill and empty 👍 200 ltr tank = 200 kg
sound ya the ones you're putting on are quieter
Your driver-side headlight is busted. Was it like that? Another small job!
i think you need to go watch motocheez channel and see what he did with his carb and how he added a supercharger to his kei truck,, its a diahatsu hijet, but its pretty similar
Check gearing, that tiny little truck probably isn't geared to go that fast, probably meant for little farm truck or something
next episode: TDI swap on the zuk. :)
check ignition timing!
Needs a Supercharger if you want to run 25'' tires..
Sluggish power could be the timing is off.
Harbour Freight manuel tire machine is better option, been using one for over 20 years....
the cat might be clogged on it for the lack of power if it has one
Next time mount the tire on something, the tire can pop up and break your wrist if the tire flips off the rim.
I love desert cars and I don't own one💔
👍👍❤❤❤
lookers F and B
Hey Austin! I been hooked on your channel! You are truly amazing! What size tires and rims did you put on in this tire video? And brand please?
Kubota diesel swap ot
Austin that is no a truck for plowing mate definitely not for that application
Oh no!!!
A breaker bar is not a torque wrench.
Zuk? Żuk?
'
oh i like that suzuki truck...
how come american company dont make it their own mini trucks
motor swap it
Mud flap brackets little rusty... be a shame to powder coat it...
That would be a shame haha
sorry but the tires you're taking off get better traction than the ones you're putting on it has been my experience.
You and cameron brothers? or related?
Yes we are brothers!
Why is your videos hiding from me.
Need a bigger engine