Great video. We have a California Pellet Mill which is just a few blocks from where I live. I watched one of your other videos and have found these very informative. I hope I can get to see the inside of ours some day.
I'm beyond jealous of how easy this is compared to the dinosaur I have to repair.. the dies are twice the size and instead of two rolls, there's 3 rolls... I think the rolls we have are also at least 3-4 inches in diameter wider.. this is ridiculous 😂
We don't even have die clamps on our pellet machines... We have to heat the insert with a rose bud to 180-200° f and slip the die in and bolt it down.... Then there's a stiffening ring on the outer ring we have to heat up as well and slip that on there and then the shroud is fastened to the stiffening ring.... I WISH we had pellet mills like this.. this looks like cake work..
I used to be a pellet Mill operator and changing pellet mill dies were never that easy for us we had a die cart and we pulled the whole assembly out rollers and all and a safety precautions used in this video was never used I work for Martindale feed Mill out of Texas.
We do the same but we usually leave the #1, (or the top roll) in it so if the wench fails for some reason it doesn't fall and hit the #1 shaft, or the floor... Or your feet x.x
Look's like LOTO procedures need to be gone over with the employees. Every person working on the equipment must affix their LOCK & TAG to the cutoff switch I saw 2 people on that job. Somebody is going home with a pink slip in his hand. I seen plenty go home from the place I worked at just helping for a minute with no lock on.
@@michaelschardan5312 sand, mineral oil, and oats , mix all together run it through your pellet Mill for at least 30 minutes reusing what you've already mixed up so you will need to block the entrance to the cooler .
![ละลาย (LALALYE) - DAOU PITTAYA ต้าห์อู๋ พิทยา [OFFICIAL MV]](http://i.ytimg.com/vi/wo6r9TgausI/mqdefault.jpg)
Great video. We have a California Pellet Mill which is just a few blocks from where I live. I watched one of your other videos and have found these very informative. I hope I can get to see the inside of ours some day.
Bro... We have the paladin pellet machines from the 80s where I work.. I WISH it was this simple
I'm beyond jealous of how easy this is compared to the dinosaur I have to repair.. the dies are twice the size and instead of two rolls, there's 3 rolls... I think the rolls we have are also at least 3-4 inches in diameter wider.. this is ridiculous 😂
use to work in a mill , die changes were a pain to do
I resign from this kind of job. Hahaha too hard for me. I thought it was easy pezzy
We don't even have die clamps on our pellet machines... We have to heat the insert with a rose bud to 180-200° f and slip the die in and bolt it down.... Then there's a stiffening ring on the outer ring we have to heat up as well and slip that on there and then the shroud is fastened to the stiffening ring.... I WISH we had pellet mills like this.. this looks like cake work..
Why roller-shells are easy to be worked out
Within a short time?
Good video. Thanks for showing it.
I own a pellet stove & somehow this arrived in my feed. Pretty scary how much Google knows about each of us.
I used to be a pellet Mill operator and changing pellet mill dies were never that easy for us we had a die cart and we pulled the whole assembly out rollers and all and a safety precautions used in this video was never used I work for Martindale feed Mill out of Texas.
We do the same but we usually leave the #1, (or the top roll) in it so if the wench fails for some reason it doesn't fall and hit the #1 shaft, or the floor... Or your feet x.x
what is the reference on the tool ingersoll rand?
Aguem responde ser a regulagem dos rolos é um para baixo e o outro para cima?!
Am from Indonesia, i problem to mesin Wood pellet, what you solusi to me? Plis 🙏🙏
I dont operate this brand of mill, but our die changes take hours
Can kindly send electrical diagram video of 53f pellet IDAH
Please send me matching position of roller shell and dai.
Now try this on a working pellet mill made by cpm not that easy lol perhaps one that uses molasses. See how that works out for yea
Hell we dnt use none of that but we run big mills
Yo trabajo en una industria de alimento balanceados y los dados y rodillos se dedgastan muy rapidos
Mucho ajuste u mezcla agresiva
Alimentos con maiz, como alimento de gallina, gastan mas rapido los dados y rodillos
Look's like LOTO procedures need to be gone over with the employees. Every person working on the equipment must affix their LOCK & TAG to the cutoff switch I saw 2 people on that job. Somebody is going home with a pink slip in his hand. I seen plenty go home from the place I worked at just helping for a minute with no lock on.
If anybody wants to know how to break a new die in let me know if they happen to be in this industry.
Hello I'm in the industry. What the method you use to break in?
@@michaelschardan5312 sand, mineral oil, and oats , mix all together run it through your pellet Mill for at least 30 minutes reusing what you've already mixed up so you will need to block the entrance to the cooler .
I whis i have this machine ....
Xk nose desgastan los roles paregos
Rulo ayar videosu yokmu?
nice informative
Fine!
Buy KAHL save all your head