In the event you are seeing two labels at the roadway crown you can remove the unnecessary label by changing the properties of one of the lanes. Try this... Select one of the lanes in your assembly, then visit the Properties Palette (press Ctrl+1) and change the "Inside point code" to "none". This will prevent the redundant marker from being labeled.
Excellent presenter. Takes special talent to master a subject, then translate the material to a teaching platform that is easily consumed. Great Job Jeff.
Jeff, Hopefully you still get notifications about comments on this. I am trying to have sections produced of a track but seem to have an issue with the sections when the track is above existing ground level. Your sections show a specific thickness of most likely subbase and then the fill line extends beyond the subbase thickness to the existing ground. Say i wanted to illustrate the capping material beneath the subbase, is it possible to make the capping material target a specific depth beneath existing ground? Say you have 150mm subbase onto 200 capping, but if the underside of the capping is above existing ground level it is shown as floating whereas we desire it to be at least 150mm within the existing ground so the capping may be in excess of 400mm thick at that point. Is this possible? Your advice would be much appreciated. Kind Regards, Adam
BY THE WAY, WHICH SUBASSEMBLY IS THE LANE?, ALL LANE SUB ASSEMBLY IN Civil 3D 2017 vertically End in two outer end, while here it is sloped, i could not find this kind sub assembly in Civil 3D 2017
Hey Jeff! Do you have any tips or video on how to put out text on structures for levels in plan? And numbering them? Is there any easy way for labels? I think i did it for couple a years ago with just a click somewherr
Thanks for sharing the videos. In case if we want to apply different correct sections let's say 15 kms, can we upload all in one go with different TCS in this 15 kms.
Jeff, how can i make the Crown point from duplicate? im seeing the label in both side and i don´t need that. I tried changing the "inide point code" to none, and nothing happend...
Great video! Unfortunately when I tried staggering I ended up with 2 labels at the crown. I have 2 subassemblies with crown codes along the centerline so 2 labels get created. Any way to avoid this?
Unfortunately when I go to select the "Label Set" within the section group properties -- it does not select it at all. It wont even allow me to select "No-Labels". Do you happen to know why this might be happening? Could something be locked ? Appreciate all of your videos and help-- they are excellent :)
Dear Jeff Bartels i have Land Desktop Civil 3d 2009 Companion 32 Bit. But My Operatiing System is 64 Bit So, i,m Not able work on land desktop 32, if you have a link of Land Desktop 64 bit, kindly send me. & if you have other solution send me. hopping a good response & early action (
In the event you are seeing two labels at the roadway crown you can remove the unnecessary label by changing the properties of one of the lanes. Try this...
Select one of the lanes in your assembly, then visit the Properties Palette (press Ctrl+1) and change the "Inside point code" to "none". This will prevent the redundant marker from being labeled.
Excellent presenter. Takes special talent to master a subject, then translate the material to a teaching platform that is easily consumed. Great Job Jeff.
Excelente from any point of view. Short, concise, and loaded with useful information. Pedagogical.
Jeff, Hopefully you still get notifications about comments on this.
I am trying to have sections produced of a track but seem to have an issue with the sections when the track is above existing ground level. Your sections show a specific thickness of most likely subbase and then the fill line extends beyond the subbase thickness to the existing ground. Say i wanted to illustrate the capping material beneath the subbase, is it possible to make the capping material target a specific depth beneath existing ground? Say you have 150mm subbase onto 200 capping, but if the underside of the capping is above existing ground level it is shown as floating whereas we desire it to be at least 150mm within the existing ground so the capping may be in excess of 400mm thick at that point. Is this possible? Your advice would be much appreciated.
Kind Regards, Adam
BY THE WAY, WHICH SUBASSEMBLY IS THE LANE?, ALL LANE SUB ASSEMBLY IN Civil 3D 2017 vertically End in two outer end, while here it is sloped, i could not find this kind sub assembly in Civil 3D 2017
Hey Jeff!
Do you have any tips or video on how to put out text on structures for levels in plan? And numbering them? Is there any easy way for labels? I think i did it for couple a years ago with just a click somewherr
Thanks for sharing the videos. In case if we want to apply different correct sections let's say 15 kms, can we upload all in one go with different TCS in this 15 kms.
Jeff, how can i make the Crown point from duplicate? im seeing the label in both side and i don´t need that. I tried changing the "inide point code" to none, and nothing happend...
Thank' s Jeff for this short presentation! I love it.
I have enjoyed your videos. Very clear and precise.
Thanks James!
Great video! Unfortunately when I tried staggering I ended up with 2 labels at the crown. I have 2 subassemblies with crown codes along the centerline so 2 labels get created. Any way to avoid this?
Superb illustrations and demonstration
Thank you!
Unfortunately when I go to select the "Label Set" within the section group properties -- it does not select it at all. It wont even allow me to select "No-Labels". Do you happen to know why this might be happening? Could something be locked ? Appreciate all of your videos and help-- they are excellent :)
how i export the cross section existing ground station and offset from civil 3d to excel?
It's Great Jeff
You have any sample questions for Autodesk civil 3D professionals exam
any links for the templates in section views, plan and profile views?
Amazing video clip....thanks Jeff
So glad to hear the content was helpful!
Eng / Jeff please how can I get ADSK section stilye plot please ?
It's great.
How i can set all point label are readable in project objects to profile view.
How can I change. My labels units from feet to meters
Dear Jeff Bartels i have Land Desktop Civil 3d 2009 Companion 32 Bit. But My Operatiing System is 64 Bit So, i,m Not able work on land desktop 32, if you have a link of Land Desktop 64 bit, kindly send me. & if you have other solution send me.
hopping a good response & early action (
Excellent!
Many thanks!
Congratulation Jeff!
bonjour, j'ai besoin de votre aide, j'ai besoin de profil en travers ferroviaire pour voie unique civil 3d
thanks. very well
Your wisdom is staggering.
Can you share your dwg files?
I like your videos , upload more please :)
The fucking habit of using inches, feet,... instead the International System of Units as the rest of the world.
Don't really give a fuck about what the rest of the world does. We do it this way.