3D Printable Hinge in Fusion 360 tutorial

แชร์
ฝัง
  • เผยแพร่เมื่อ 30 ต.ค. 2024

ความคิดเห็น • 91

  • @anonimuso
    @anonimuso 5 ปีที่แล้ว +5

    This video is a good companion video to the Maker's Muse one because Angus just talks about hinges, he doesn't actually show you how to design one in the software. I'm trying to do this in Autodesk Inventor, so I hope the commands are similar. :) But watching this gave me a general idea of how to do it.

  • @maxbarbul
    @maxbarbul ปีที่แล้ว +1

    Thank you for this tutorial! Despite using a newer version, I was able to match all needed actions, thanks to your explanations and remarks.

  • @gaWalt
    @gaWalt 4 ปีที่แล้ว +2

    Tomas, thanks for clearly explaining the process of making a hinge using Fusion 360!. My sample worked the first time!
    This was my first hinge.

  • @needge
    @needge 3 ปีที่แล้ว

    Perfect i was searching for this tutorial after Maker's Muse Video

  • @mousa65
    @mousa65 4 ปีที่แล้ว +2

    I am new using Fusion 360 and you explained how to make this hinge very well and I printed it later and it was perfect thanks for sharing your knowledge

    • @mistertravorjr.6036
      @mistertravorjr.6036 4 ปีที่แล้ว

      Did you print it as one thing?

    • @mousa65
      @mousa65 4 ปีที่แล้ว

      Hello
      Yes, of course, it is printed on one piece and is slightly joined in the center, but then separates the two pieces by hand.

  • @CroPrepper
    @CroPrepper 4 ปีที่แล้ว +14

    people complaining about audio like they came to listen to a song. Dont mind the audio, the content is important.

    • @artistryartistry7239
      @artistryartistry7239 4 ปีที่แล้ว +2

      Listening to static and constant white noise might be fine for you. But don't purport to tell other people what's acceptable for them.

    • @forgotrafe
      @forgotrafe 3 ปีที่แล้ว

      @@artistryartistry7239 indeed. I’m partially deaf in one ear and even with headphones I’m really struggling with this video.

  • @arpadpinter6050
    @arpadpinter6050 5 ปีที่แล้ว +20

    3:30
    which is going to present the AAAAAAAAAAAAAAAAAAAAAAH as i call it

  • @xXxDJDANxXx1
    @xXxDJDANxXx1 5 ปีที่แล้ว +1

    Thank you so much for creating this video. i was wanting to make a custom hinge for my 3d printer enclosure because didn't like shop brought and couldn't find any that i like on thingiverse so ive used this guide to create my own custom one. once again thank you for share this. helped me out a lot

  • @adrianakaye423
    @adrianakaye423 6 ปีที่แล้ว +9

    Video shows how to make a hinge perfectly, wish the audio was a little better but easy to follow

    • @hoggif
      @hoggif 5 ปีที่แล้ว +1

      For a non-native english speaker the audio is sometimes pretty difficult to follow. I wonder how that kind of audio can be done in the first place (without using phones, skype or other very tight codecs with a poor line)

  • @benjamin1832
    @benjamin1832 2 ปีที่แล้ว

    You worked very well, I'm a little curious why you work upside down, it's hilarious, jajaja 😂 😂

  • @memonsalmaanmohammedirfan7435
    @memonsalmaanmohammedirfan7435 2 ปีที่แล้ว

    Very nice. Thanks!

  • @chrisjericho7123
    @chrisjericho7123 6 ปีที่แล้ว

    Thank you. I followed this and got it to work. using this I can modify it for a project. i also learned a little more about certain commands you used.

  • @RLS1010w-wh
    @RLS1010w-wh 3 หลายเดือนก่อน

    Cool👍

  • @Bion479
    @Bion479 6 ปีที่แล้ว

    Brilliant Video, I have learnt loads about fusion from it thanks :)

  • @matthewcarrellful
    @matthewcarrellful 5 ปีที่แล้ว +3

    thanks Thomas your wallpaper made me laugh

  • @javixuPichus
    @javixuPichus 3 ปีที่แล้ว

    Thanks grate video tutorial

  • @phreedumbphighter
    @phreedumbphighter 6 ปีที่แล้ว

    Nice video. Easy to follow. Thanks for making it.

  • @nasugaming-chip5298
    @nasugaming-chip5298 4 ปีที่แล้ว

    Super helpful

  • @shark_one4062
    @shark_one4062 5 ปีที่แล้ว

    Thanks a lot bro, my first Hinge !

  • @devstefancho
    @devstefancho 5 ปีที่แล้ว +1

    Thanks for a great video , I have a question
    Is this no need for support?
    or I just can print it ?

    • @maenova417
      @maenova417  5 ปีที่แล้ว +1

      Print without supports, completely flat. The tolerances in the hinge will let it move and not fuse together :)

    • @devstefancho
      @devstefancho 5 ปีที่แล้ว

      Tomas Svitil Thanks for your fast feedback
      then how can I know the maximum tolerance? you use 0.3mm for gap
      Is this related to nozzle size?(0.4mm)

    • @maenova417
      @maenova417  5 ปีที่แล้ว +1

      @@devstefancho it is specific to your printer - how accurately it can print. The easiest way to find out is to print an accuracy gauge like the one from Makers Muse. Or just print and keep changing the tolerance until you get a a good print. You can expect it to be 0.2~0.5 depending on how good your printer is :)

    • @devstefancho
      @devstefancho 5 ปีที่แล้ว +1

      Tomas Svitil I will try this
      Thanks for your feedback again!

    • @stephenman3846
      @stephenman3846 5 ปีที่แล้ว

      @@maenova417 hiii but can i print without support becuase i modified the design abit

  • @itsfragsz7345
    @itsfragsz7345 ปีที่แล้ว

    hi is there any other way to create allowance for the hinge to move at 10:22 ? i think its because new version of fusion hence i do not have the feature of going back to the first part

  • @nedu1741
    @nedu1741 5 ปีที่แล้ว

    Thank you so much! Very informative

  • @misamalirizvi1610
    @misamalirizvi1610 4 ปีที่แล้ว

    Nice

  • @Leif_YT
    @Leif_YT 6 ปีที่แล้ว

    Thank you, great video.

  • @Josh-gj3vo
    @Josh-gj3vo 2 ปีที่แล้ว

    Hi i reallying enjoy your video honestly that's the one i need it right now, can you do me a favor to put the file in description😅 please🥺

  • @neddy1703
    @neddy1703 4 ปีที่แล้ว

    Would this actually print in place and work? I’m not sure it would...
    which orientation would you print it? It has overhangs greater than 45 degrees in all orientations from what I can see...

    • @maenova417
      @maenova417  4 ปีที่แล้ว

      Hey Neddy, yes, this will print in place on most modern printers.
      Make sure to print without supports. You'd be surprised how well 3D printer can print in air without any supports.

  • @ContempoBigBand
    @ContempoBigBand 4 ปีที่แล้ว

    Thankssssss!!!

  • @marylynch8929
    @marylynch8929 6 ปีที่แล้ว

    Thanks for tutorial :)

  • @zebanya8418
    @zebanya8418 2 ปีที่แล้ว

    Hello i just have a question how thin can i make a hinge?

  • @RaadYacu
    @RaadYacu 6 ปีที่แล้ว +1

    Thomas this is an excellent video on hinges. you should have more videos

  • @fpv568
    @fpv568 4 ปีที่แล้ว +2

    great video, as others pointed out, investing in a better mic would make your videos much more enjoyable to watch!

  • @ranjinia
    @ranjinia 7 ปีที่แล้ว +3

    beautiful goat impression at 3:31

    • @bobafett5640
      @bobafett5640 6 ปีที่แล้ว +1

      rip headphone users

  • @sonnigundbelanglos
    @sonnigundbelanglos 4 ปีที่แล้ว +1

    could you give the data to this hinge, it looks exactly like the one I need :)

  • @HarshaVardhanOnco
    @HarshaVardhanOnco 6 ปีที่แล้ว

    Good video Sir! Can you please also demonstrate how to 3D print all the components. If we 3D print them as it is, then we can't get to snap the two parts. How do you separate the shaft of the joint?

    • @maenova417
      @maenova417  6 ปีที่แล้ว

      Hey Harsha, this is actually meant to be printed as a single piece. You have to figure out the tolerance of your 3D printer. Angus at Makers muse made a great tester, if you Google 3d printer tolerance gauge. Then you need to set the tolerance between the hinge and the body to the value you find. E.g. for my cetus printer it's 0.2mm, so if the hinge rod diameter is 5mm, then I'll make the rod holder diameter 5.2mm. You need to try a few prints and see what works best for you :)

  • @brandonkennethnowaseb4511
    @brandonkennethnowaseb4511 4 ปีที่แล้ว

    Hello Kevin, I've to say i learned a lot from your Fusion360 tutorials, now i was wondering if you could do a tutorial with a stylish pillar. Will be highly appreciated

    • @maenova417
      @maenova417  4 ปีที่แล้ว +2

      I'm Tom tho 😢
      What do you mean by stylish pillar?

  • @peterskowronski6248
    @peterskowronski6248 5 ปีที่แล้ว +8

    Great content, too bad the audio is bad, and you go way too fast. Hope you remake this video at some point.

  • @ciceroaurelius3757
    @ciceroaurelius3757 4 ปีที่แล้ว

    also its a good video

  • @4funrc11
    @4funrc11 6 ปีที่แล้ว

    Hey! Pretty cool! Waiting for "next time". :*)

  • @yasirekingen8822
    @yasirekingen8822 5 ปีที่แล้ว +3

    I guess microfon 3d printed too

    • @maenova417
      @maenova417  5 ปีที่แล้ว +2

      :D

    • @michaels3003
      @michaels3003 3 ปีที่แล้ว

      Maybe he does not live on Earth.

  • @RCyoutube88
    @RCyoutube88 5 ปีที่แล้ว

    thank you !

  • @ehseaglesofdesign7957
    @ehseaglesofdesign7957 6 ปีที่แล้ว

    Nice tutorial. I'd like to show this to my high school students but there's an f-bomb in the first seconds. Ha ha. It's ok I love my coffee too. Cheers ps I might still show it

  • @mordechairothschild3042
    @mordechairothschild3042 5 ปีที่แล้ว

    Can i export it to sketch up and then attach it to an existing object?

    • @maenova417
      @maenova417  5 ปีที่แล้ว

      I don't see why not. But I think it' be better to just model it directly, that way you'll have more control :)

  • @mog99lie
    @mog99lie 6 ปีที่แล้ว +9

    Audio, I had problems following and gave up after the first minute.

    • @golferchin76
      @golferchin76 6 ปีที่แล้ว +3

      So you did not learn from this excellent tutorial. what a shame.

    • @DaxmathecoolNobodie
      @DaxmathecoolNobodie 6 ปีที่แล้ว +4

      How can you learn when he's literally talking into a potato? I've been playing this video over and over for the past hour just trying to understand what he's saying because news alert not everyone can speak fucking potato like you can.

    • @djmason9
      @djmason9 5 ปีที่แล้ว +3

      I have the same problem he needs to take the potato out of his mouth

  • @thinkithink648
    @thinkithink648 4 ปีที่แล้ว

    good....

  • @oscardaolio393
    @oscardaolio393 5 ปีที่แล้ว

    Really useful! Good hints..but better audio pls...even if everything can be followed just by watching.Thx!

  • @TheCastle11111
    @TheCastle11111 5 ปีที่แล้ว

    How would you insert the pin?
    I don't catch that part.

    • @justenhansen
      @justenhansen 5 ปีที่แล้ว

      You can print them together on a 3d printer already assembled. They can't come apart.

    • @TheCastle11111
      @TheCastle11111 5 ปีที่แล้ว

      @@justenhansen oh really. just figured that out. Thx mate;)

  • @sunpeter8260
    @sunpeter8260 5 ปีที่แล้ว +1

    Thanks for the excellent tutorial! I have to mention so many others have already complained. This nice tutorial is totally spoiled by the horrible audio! What a pity!

  • @ciceroaurelius3757
    @ciceroaurelius3757 4 ปีที่แล้ว +1

    SLOW DOWN

  • @michaelcook3794
    @michaelcook3794 5 ปีที่แล้ว +2

    So, you are going with that audio ??? Huh.

  • @MrPvallone
    @MrPvallone 5 ปีที่แล้ว

    Good video, but invest in a better microphone

  • @thejetshowlive
    @thejetshowlive 6 ปีที่แล้ว

    How does this print without supports?

    • @maenova417
      @maenova417  6 ปีที่แล้ว +1

      thejetshowlive great, you want to print without supports.

    • @chrisjericho7123
      @chrisjericho7123 6 ปีที่แล้ว

      Most 3d printers can bridge short distances ( if tuned properly) without the plastic running down onto what below it. Remember this is layers, so after the last layer of the INSIDE of the bottom of the hole, after a few layers it will start to print the bar that goes through the hole. it will bridge the plastic from the two sides and start to build the middle piece. After teh middle piece is done, it will start to front the top on the hole and continue to the top to the model.

    • @iggusify
      @iggusify 6 ปีที่แล้ว

      Very good question! And thanks for the replies! I still don't get it, however. Is the hinge supposed to be printed laying down, with the pin horizontal? In that case, wouldn't the pin fuse with the inside of the hole?

    • @golferchin76
      @golferchin76 6 ปีที่แล้ว +1

      print laying down, and not it will not fuse, as long as you know what's the tolerance of your FDM printer. You can try this and see that when it starts to print the pin, the first layer of it is only a line or two, technically there's contact and fuse but due to the contact area is so small and thus weak, after printing you apply force to turn the hinge, the contact point breaks and you have a free moving 2 parts.
      My FDM printer's tolerance is 0.1-0.15 mm at this 5mm thick design.

  • @ethanillidge9768
    @ethanillidge9768 5 ปีที่แล้ว

    fix your mic but good video

  • @keldsor
    @keldsor 5 ปีที่แล้ว

    why this crappy sound ?

  • @designstudie
    @designstudie 3 ปีที่แล้ว +1

    very bad sound

  • @Tizocr
    @Tizocr 2 ปีที่แล้ว

    the sound is horrible

  • @djmason9
    @djmason9 5 ปีที่แล้ว

    Why do you have to have the F word at the beginning of your video it rains it for kids who would like to learn 3-D printing

    • @maenova417
      @maenova417  5 ปีที่แล้ว

      It was my wallpaper at the time

    • @djmason9
      @djmason9 5 ปีที่แล้ว

      @@maenova417 yeah i got that part but maybe you could have edited your video to remove it thats all im saying..

    • @maenova417
      @maenova417  5 ปีที่แล้ว +1

      @@djmason9 fair enough, next time

  • @dakadaka7455
    @dakadaka7455 4 ปีที่แล้ว

    cringed so hard