Hello , I need some help. I inherited a e model 4gb corora with rgh2 xdk chip. I rewired it to upgrade it to rgh3. Ran flashdump.bin file through jrunner and converted it to rgh3. My problem is that it now only boots to xell via eject button. If I use the power button, I just the green light and it's black screened. I looked at jrunner and there are no blocks or errors. I unfortunately don't have the original dump. Just the dump I did when it was rgh2. I have been going at this for 2 days now with no avail. Any help is welcome. Ps. I have checked the wiring and it is good. I also don't have wb2k ram.
I'm sorry I'm so late to reply...first check all connections and solder points and the HDMI. Then try switching to the older AV cables and attach that to the screen. I've seen that refused display via the HDMI but would on the AV cables after a flash ....weird but reflashing fixed that. Make certain when you selected the RGH3 glitch also in JRunner that it's doesn't have an outdated kernel selected by default ....this happened to me just the other day. Let me know how it goes and where your at, I'm glad to help when I'm available.
YOO i have the same problem on my xbox 360 slim .. after i messed around with some dash board settings i disabled xbox live blocker then the xbox updated and it won t turn on again ... any tips on how to get it run again??
Hello, I really do not understand what to put in LDV Value. I am doing this because i have a bad block and cannot boot to XeLL. How can i count "f" if i cannot boot to Xell? or maybe LDV Value is shown in JRunner (on the right side) when i firstly load the nand.bin (with the bad block error)???
Help me mr i want your help. I have xbox360 JTAG/Rgh corona 4g. During update i switch off the console after turn on it's showing red light. Or but when turning on console from eject button it's opening in xell reloaded
@@TextText-j1q check to see if it's overheating. Open the console. Then use a external fan, even a box fan will work to blow more air on the GPU under the internal fan and try powering it on. If the red light goes away you have a overheating issue and I'd recommend replacing the thermal paste and perhaps replacing the stock fan with one with better airflow. Let me know if this works, if not I can help you check for other faults 😊
@@TextText-j1q if the NAND is now corrupt but you've downloaded your dashboards you can rebuild the NAND and you should still be able to access your pre-installed dashboards and saves as they're stored on the hard drive. Follow these steps: 1)Backup Your Data: Before attempting any repairs, ensure you have a backup of your current NAND and any important data on your hard drive. 2) Re-flash the NAND: Use a hardware NAND flasher to re-flash your original or a working NAND dump. This can often resolve issues with corrupt NAND1. 3) Check for Bad Blocks: If there are bad blocks in the NAND, ensure they are remapped correctly during the flashing process1. 4) Restore Dashboards: After successfully repairing the NAND, your dashboards like Aurora should still be on your hard drive. If they are not accessible, you may need to reinstall them.
I have xbox one 1540 dvd drive isnt working tried everything changed the laser the motherboard with dvd drive board replace didnt help i ordered a new dvd drive but not sure how to pair it Is it the same process on xbox one?
@@Mylotheblacknwhitecat alternatively if you can find a board from the exact same model as yours, you can use it and swap out the board in your new drive. This requires soldering but it's pretty easy.
Hello Repair Studio. If I don't know the CPU key of my console (because I never managed to run XELL) but I know the LDV, can I use a donor with the donor's CPU key, or do I need to know my own CPU key? Also, should the creation be set to Glitch2 - SMC+ or Glitch2 - RGH3?
@@dimitrisking7590 You can use a donor yes. Also as far as the glitch it depends on which one your doing. If your going the RGH3 route then choose that but if your using a chip you can use RGH glitch2 or glitch2-SMC....it breaks down like this: 1) RGH 1.2: This is often used for older Xbox 360 models (Phat consoles) and some Slim models. It’s known for its stability and relatively quick boot times. 2) RGH 2.0: This is used for newer Slim models and is necessary for consoles with a dashboard version higher than 14719. 3) S-RGH: This is a variation of RGH 2.0 that can offer faster boot times on some consoles. 4) Glitch2-SMC+ is a variant of the RGH 2.0 method, which uses an optimized SMC (System Management Controller) to improve boot times and stability. This method is particularly useful for certain Xbox 360 models, such as the Zephyr and Falcon, so best for older models in my experience. Zephyr's can be finicky so be aware if that's the model your working on. 🙂
@@repairstudio4940 Thank you very much for the quick response! I will use the RGH3 method. So, as you described, I don't need to know the CPU key of my console since I will be using the donor's CPU key. Therefore, I will follow your steps on my Jasper 256MB console with RGH3. Is there anything else I should be careful of for Jasper 256MB? If it works,I will post it on your channel! Thanks for your response!
@@dimitrisking7590 Nah Jaspers and Falcons do quite well actually. I would make certain once you get a donor CPU key to try to find a key of a console the same year and model with the same disk drive and drive key, retrieve your drive key, or replace the drive with a donor drive and key otherwise your console may not read the disks. Let me know how it goes. 🙂
Was hoping this would fix mine but unfortunately nothinf changed. Rgh 3 trinity. Ive checked rhe wiring and made sure all solder points were good. Flashes fine but after system will turn on but no screen input. Fan starts up normal and runs but every 5 seconds it sound like the fan restarts.
Haha ... Quality does indeed suck, hence why I've just decided not to TH-cam anymore. I can repair anything on these consoles but the quality isn't up to par. Im a repair tech not production company. Meh, no love lost though glad it helped.
Sorry I just saw this, I work often. This is common no worries... When you rebuild the NAND in JRunner for your RGH Xbox 360, the disk drive might stop working due to a mismatch between the drive’s firmware and the console’s NAND. Here’s what you can do to fix it: 1) Check the DVD Key: Ensure that the DVD key in the NAND matches the one in the drive. If they don’t match, the drive won’t work. You can find the DVD key in JRunner under the “Key Vault” tab. 2) Reflash the Drive: If the keys match but the drive still doesn’t work, you might need to reflash the drive’s firmware. Use a tool like JungleFlasher to reflash the drive with the correct firmware. 3) Verify Connections: Double-check all the physical connections between the drive and the motherboard. Sometimes, a loose cable can cause the drive to malfunction. 4) Rebuild NAND with Correct Files: Make sure you used the correct files when rebuilding the NAND. Incorrect or corrupted files can cause various issues, including problems with the disk drive. 5) Update Dashboard: Ensure your console’s dashboard is up to date. Sometimes, an outdated dashboard can cause compatibility issues with the drive. Sorry so late but hopes this helps....let me know if you need further help.
I tried rgh3 but after write xell the problem came that's when i tried turn on my xbox 360 trinity it doesn't boot and just made bipp sound (no green light).. I assume that my nand got brick and i dont know how to get cpu key.. Do you have ane solution?
@@wjyaa618 tysm for the fast reply, I think im going to put another week on this and see what happens… If I may ask how much you sold it for?/or how much can I sell it on these conditions?
@@repairstudio4940 hi i fixed it by making a donor nand with no nanddumps source only cpu and dvd key that worked. Some how i flashed mu CONSOLE with the wrong glitch xell worked but not normal boot its. Fixed. Now
@@RGHPLUG if you have the key you can rebuild with it. Also donor keys are available online in many forums. Many donate keys from broken consoles. The 360 community is huge! I'm glad you got it up and going, curious though is it a Corona?
Hy my 360 its a 2006 xenon i bricked it when i was trying to flashing the 2011 metro dashboard but where you choose the mod type i accidentally put glitch 2m (mine its glitch 2) when i flashed it it gave me black screen and i cant boot on xell any suggestions?
Have you reflashed it? That'd be my first step as many issues like accidently choosing the wrong glitch (which affects alters the timing) causes issues. Different mod chips and the RGH3 using a pico affect timing but saving and backing up your nand dump is SO important so it's simple to just reflash. Sorry for the delayed reply. Hope this helps. 😎👍🏻
I dont know how to remove the mod chip from the board because i bought over 1 year ago from ebay and the seller told me that if i want to repair the console i need to pay 60 euros (the console costed 45 euros)
@@francescogrilli7620 if possible upload a video here on TH-cam and I'll guide you. You only need to desolder the wires from the board however if this is a Corona then a post-fix adapter may also need to be removed. It will be a small white board around the CPU.
Ahhh the good ole flashy flashy green middle light...am I right? 😏 First reflash the nand back to retail using the saved dumps....what kernel version are you using and what mobo?
I have the same problem but when I follow your guidelines some squares remain blank from the information like a box:6BL[cf] patch0 and 7BL[cG] patch0 and others
Uggh betcha RGHing a Corona huh? They give everyone a run for their money ... So testy. Personally I try to stick to Trinity models but there's some Coronas I had to fight a week or so or more! They are just so weird!
Thought I'd drop back in and say you could replace the drive and clone it to a new drive using free software like Reflect. Also clean and ipect the cable and pins. Let me know how it goes...thanks. Sub plz ...more much cooler vids coming...Happy Holidays! 🎅
Well I'm having an issue with a 16mb corona I did a rgh3 wire install wrote xell it worked got the cpu key but after writing the custom image the system wouldn't power on only the beeping sound so I tried your method and the same thing happened
@@wesleylyght9373 ahhh the old beep beep beep...yes I know where your at. Your going to have to flash it using your saved Nand dumps and then go through the process again as if had never been flashed. In JRunner go to Load Source there should be a folder in output then under the extras folder called nandump1.bin and nandump2.bin, use the first one as the source by clicking it then in Load Extra go back and get the nanddump2.bin then compare and Write Nand.
@@nomoral7500 this will not brick your console please give details and I can help you through the process of getting your machine up and running again ...
This error is usually due to a corrupted file. Make certain your drive is secure in the console and try again, if it still isn't working then it's probably a file issue. Let me know and I can provide additional help.
![How to Dump & Flash JTAG/RGH NAND from XeLL [Tutorial]](/img/n.gif)
This video saved me. Keep up the excellent work.
Glad it helped! I've been super busy but I plan to beat this YT channel into submission and get back to it 😎
I worked for me i bricked my 4gb and it worked i did exactly what u did and it work tbh thank you very much helped me alot
Always
?? You have Xbox 360 rgh corona 4g
Hello , I need some help. I inherited a e model 4gb corora with rgh2 xdk chip. I rewired it to upgrade it to rgh3. Ran flashdump.bin file through jrunner and converted it to rgh3. My problem is that it now only boots to xell via eject button. If I use the power button, I just the green light and it's black screened. I looked at jrunner and there are no blocks or errors. I unfortunately don't have the original dump. Just the dump I did when it was rgh2.
I have been going at this for 2 days now with no avail. Any help is welcome.
Ps. I have checked the wiring and it is good. I also don't have wb2k ram.
I'm sorry I'm so late to reply...first check all connections and solder points and the HDMI. Then try switching to the older AV cables and attach that to the screen. I've seen that refused display via the HDMI but would on the AV cables after a flash ....weird but reflashing fixed that. Make certain when you selected the RGH3 glitch also in JRunner that it's doesn't have an outdated kernel selected by default ....this happened to me just the other day. Let me know how it goes and where your at, I'm glad to help when I'm available.
any info on "how to attach the flasher to the consol" please
Certainly are you looking for the direct pinouts from a NandX or JR Programmer?
Just let me know and I'll guide you 😇
YOO i have the same problem on my xbox 360 slim .. after i messed around with some dash board settings i disabled xbox live blocker then the xbox updated and it won t turn on again ... any tips on how to get it run again??
Certainly first do you have the nand reads...original nand dumps? Sorry for the delay holidays ya know...
Got a 16mb Trinity and it wont boot into xell, any suggestions
Did you try reflashing and also check your solder joints
Hello, I really do not understand what to put in LDV Value. I am doing this because i have a bad block and cannot boot to XeLL. How can i count "f" if i cannot boot to Xell? or maybe LDV Value is shown in JRunner (on the right side) when i firstly load the nand.bin (with the bad block error)???
Sorry I just saw this. You'll need a donor. Do you have the CPU key at all? Did you get any good nand dumps? If not you'll need a donor.
Help me mr i want your help. I have xbox360 JTAG/Rgh corona 4g. During update i switch off the console after turn on it's showing red light. Or but when turning on console from eject button it's opening in xell reloaded
@@TextText-j1q check to see if it's overheating. Open the console. Then use a external fan, even a box fan will work to blow more air on the GPU under the internal fan and try powering it on. If the red light goes away you have a overheating issue and I'd recommend replacing the thermal paste and perhaps replacing the stock fan with one with better airflow. Let me know if this works, if not I can help you check for other faults 😊
@@repairstudio4940 ?? How it's bricked by bad nand I think 🤔. Overheating it's not matter 🤔
@@repairstudio4940 during update it's shutdown by mistake 😭when I turn on it's showing red light issue 😔
@@repairstudio4940 can I repair by using xell reloaded 🤔
@@TextText-j1q if the NAND is now corrupt but you've downloaded your dashboards you can rebuild the NAND and you should still be able to access your pre-installed dashboards and saves as they're stored on the hard drive. Follow these steps:
1)Backup Your Data: Before attempting any repairs, ensure you have a backup of your current NAND and any important data on your hard drive.
2) Re-flash the NAND: Use a hardware NAND flasher to re-flash your original or a working NAND dump. This can often resolve issues with corrupt NAND1.
3) Check for Bad Blocks: If there are bad blocks in the NAND, ensure they are remapped correctly during the flashing process1.
4) Restore Dashboards: After successfully repairing the NAND, your dashboards like Aurora should still be on your hard drive. If they are not accessible, you may need to reinstall them.
You save my Life. Thanks my Friend \o
Always of course. 😇👍🏻
I have xbox one 1540 dvd drive isnt working tried everything changed the laser the motherboard with dvd drive board replace didnt help i ordered a new dvd drive but not sure how to pair it
Is it the same process on xbox one?
@@Mylotheblacknwhitecat you have to use the board from the old drive ....the APU and board are paired.
@repairstudio4940 oh b I don't know where my original dvd drive went I just bought another one
@@Mylotheblacknwhitecat man that's not good, other than ordering a new one from Microsoft you may just have to use it for digital downloads.
@repairstudio4940 yeah I might have to use it for digital games
I wasn't sure if j-runner would repair the new drive to my Xbox like how the xbox 360
@@Mylotheblacknwhitecat alternatively if you can find a board from the exact same model as yours, you can use it and swap out the board in your new drive. This requires soldering but it's pretty easy.
Hello Repair Studio. If I don't know the CPU key of my console (because I never managed to run XELL) but I know the LDV, can I use a donor with the donor's CPU key, or do I need to know my own CPU key? Also, should the creation be set to Glitch2 - SMC+ or Glitch2 - RGH3?
@@dimitrisking7590 You can use a donor yes. Also as far as the glitch it depends on which one your doing. If your going the RGH3 route then choose that but if your using a chip you can use RGH glitch2 or glitch2-SMC....it breaks down like this:
1) RGH 1.2: This is often used for older Xbox 360 models (Phat consoles) and some Slim models. It’s known for its stability and relatively quick boot times.
2) RGH 2.0: This is used for newer Slim models and is necessary for consoles with a dashboard version higher than 14719.
3) S-RGH: This is a variation of RGH 2.0 that can offer faster boot times on some consoles.
4) Glitch2-SMC+ is a variant of the RGH 2.0 method, which uses an optimized SMC (System Management Controller) to improve boot times and stability. This method is particularly useful for certain Xbox 360 models, such as the Zephyr and Falcon, so best for older models in my experience. Zephyr's can be finicky so be aware if that's the model your working on. 🙂
@@repairstudio4940 Thank you very much for the quick response! I will use the RGH3 method. So, as you described, I don't need to know the CPU key of my console since I will be using the donor's CPU key. Therefore, I will follow your steps on my Jasper 256MB console with RGH3. Is there anything else I should be careful of for Jasper 256MB? If it works,I will post it on your channel! Thanks for your response!
@@dimitrisking7590 Nah Jaspers and Falcons do quite well actually. I would make certain once you get a donor CPU key to try to find a key of a console the same year and model with the same disk drive and drive key, retrieve your drive key, or replace the drive with a donor drive and key otherwise your console may not read the disks. Let me know how it goes. 🙂
Using this method to flash xell? I don't have keys and dump. I bought a new nand flash drive. I need to fill xell. Will this help?
Yes you need donor keys and JRunner has the tools built in to rebuild the NAND via a donor.
Was hoping this would fix mine but unfortunately nothinf changed. Rgh 3 trinity. Ive checked rhe wiring and made sure all solder points were good. Flashes fine but after system will turn on but no screen input. Fan starts up normal and runs but every 5 seconds it sound like the fan restarts.
I have the same issue. No output tries to reboot but nothing happens
Same@@fkfkfkrkfkf5200
Same😢
Did Microsoft do something and not tell us I’m 5 Xboxes deep no fix this is stupid done trying
Hmmm... Can you upload a video and drop the link and let me see?
crap quality but it got the job done. thank you so much.
Haha ... Quality does indeed suck, hence why I've just decided not to TH-cam anymore. I can repair anything on these consoles but the quality isn't up to par. Im a repair tech not production company. Meh, no love lost though glad it helped.
help !!!after this my dvd drive is not working
Sorry I just saw this, I work often.
This is common no worries...
When you rebuild the NAND in JRunner for your RGH Xbox 360, the disk drive might stop working due to a mismatch between the drive’s firmware and the console’s NAND. Here’s what you can do to fix it:
1) Check the DVD Key: Ensure that the DVD key in the NAND matches the one in the drive. If they don’t match, the drive won’t work. You can find the DVD key in JRunner under the “Key Vault” tab.
2) Reflash the Drive: If the keys match but the drive still doesn’t work, you might need to reflash the drive’s firmware. Use a tool like JungleFlasher to reflash the drive with the correct firmware.
3) Verify Connections: Double-check all the physical connections between the drive and the motherboard. Sometimes, a loose cable can cause the drive to malfunction.
4) Rebuild NAND with Correct Files: Make sure you used the correct files when rebuilding the NAND. Incorrect or corrupted files can cause various issues, including problems with the disk drive.
5) Update Dashboard: Ensure your console’s dashboard is up to date. Sometimes, an outdated dashboard can cause compatibility issues with the drive.
Sorry so late but hopes this helps....let me know if you need further help.
I tried rgh3 but after write xell the problem came that's when i tried turn on my xbox 360 trinity it doesn't boot and just made bipp sound (no green light)..
I assume that my nand got brick and i dont know how to get cpu key.. Do you have ane solution?
I am great at what I do. Your nand is NOT (almost assuredly) bricked. Give me more info.
@@repairstudio4940 whenever I tried to turn on xbox 360, it doesn't boot (green light not turn on) and just making a bipp sound
@@wjyaa618i have the same problem on a Corona 4Gb, did you found any fix on this?
@@EmaBixD i gave up on that.. Bought new one and surprisingly I succeeded the rgh3
@@wjyaa618 tysm for the fast reply, I think im going to put another week on this and see what happens… If I may ask how much you sold it for?/or how much can I sell it on these conditions?
HI MY MAN I CANT GET IT TO WORK XELL IS BOOTING BUT NOT MY CONSOLE??
Have you tried to re-flash also did you save your first NAND dump?
@@repairstudio4940 hi i fixed it by making a donor nand with no nanddumps source only cpu and dvd key that worked. Some how i flashed mu CONSOLE with the wrong glitch xell worked but not normal boot its. Fixed. Now
@@RGHPLUG if you have the key you can rebuild with it. Also donor keys are available online in many forums. Many donate keys from broken consoles. The 360 community is huge! I'm glad you got it up and going, curious though is it a Corona?
@@repairstudio4940 hi its a Trinity that i flashed with glitch2 and not glitch2 RGH 3.0
And it messed up everything but i found a Way to fix it by using donernand files and someother stuff.
Hy my 360 its a 2006 xenon i bricked it when i was trying to flashing the 2011 metro dashboard but where you choose the mod type i accidentally put glitch 2m (mine its glitch 2) when i flashed it it gave me black screen and i cant boot on xell any suggestions?
Have you reflashed it? That'd be my first step as many issues like accidently choosing the wrong glitch (which affects alters the timing) causes issues. Different mod chips and the RGH3 using a pico affect timing but saving and backing up your nand dump is SO important so it's simple to just reflash. Sorry for the delayed reply. Hope this helps. 😎👍🏻
I tried to put the original nand but the console doesnt do anything only black screen
I dont know how to remove the mod chip from the board because i bought over 1 year ago from ebay and the seller told me that if i want to repair the console i need to pay 60 euros (the console costed 45 euros)
@@francescogrilli7620 if possible upload a video here on TH-cam and I'll guide you. You only need to desolder the wires from the board however if this is a Corona then a post-fix adapter may also need to be removed. It will be a small white board around the CPU.
hey man do you know what it means if i’m getting error 000 writing block
and now it’s flashing green
Ahhh the good ole flashy flashy green middle light...am I right? 😏
First reflash the nand back to retail using the saved dumps....what kernel version are you using and what mobo?
I have the same problem but when I follow your guidelines some squares remain blank from the information like a box:6BL[cf] patch0 and 7BL[cG] patch0 and others
So sorry I'm just now seeing this and been in the process of making more content. So in the reads it's missing blocks?
For my RGH to boot i gotta remove the hard drive and thats even hit or miss.
Uggh betcha RGHing a Corona huh? They give everyone a run for their money ... So testy. Personally I try to stick to Trinity models but there's some Coronas I had to fight a week or so or more! They are just so weird!
Thought I'd drop back in and say you could replace the drive and clone it to a new drive using free software like Reflect. Also clean and ipect the cable and pins. Let me know how it goes...thanks. Sub plz ...more much cooler vids coming...Happy Holidays! 🎅
@@repairstudio4940 i give it a try after christmas and thanks ill sub!
man i killed my console so bad that my nand x doesnt even see it lmao
Haha what? Nah haha I take it your dealing with the fun error 'no device found' situation?
@@repairstudio4940yeah, but I found out that my 4gb nand just died. I'm gonna see if I can solder another one in place
❤❤❤❤❤
Didn't work for my situation
Explain where your at man and I'll see if I can guide you and getcha up and running
What all have you done I JRunner and I'll see if I can help getcha going?
Well I'm having an issue with a 16mb corona I did a rgh3 wire install wrote xell it worked got the cpu key but after writing the custom image the system wouldn't power on only the beeping sound so I tried your method and the same thing happened
@@wesleylyght9373 ahhh the old beep beep beep...yes I know where your at. Your going to have to flash it using your saved Nand dumps and then go through the process again as if had never been flashed. In JRunner go to Load Source there should be a folder in output then under the extras folder called nandump1.bin and nandump2.bin, use the first one as the source by clicking it then in Load Extra go back and get the nanddump2.bin then compare and Write Nand.
this bricked my xbox
@@nomoral7500 this will not brick your console please give details and I can help you through the process of getting your machine up and running again ...
E 79
This error is usually due to a corrupted file. Make certain your drive is secure in the console and try again, if it still isn't working then it's probably a file issue. Let me know and I can provide additional help.