Is there a way to program the speed limits for each assist level? My ebike came with this display and it has 3 levels of assist which are programmed to be at 5 mph, 10 mph, and 15 mph. I would like to adjust this to be closer to 10, 15, and 20. Do you adjust the max speed and number of assists and does it just evenly divide the max speed by the number of assist levels you set it to? Also, my display is frozen and will not allow me to adjust certain settings. It is not password protected. It's odd!
Change PO5 from 3 to 5 this will alow more speed options, there is no setting each level, but by going to 5 levels that may get you where you want to be also make sure p08 is at 100.
If i change it to 5 levels it does'nt work, in every mode de bike wil going 25km/h. The problem is, i can't drive slower then 15km/h if the motor is on. How can i fix this? The bike is deliverd without a trottle. I hope that you can help me.
Go. To p 05 and change it to 5 pedal assist mode. This will pretty much get you. What you're asking for that's the only way you're going to get that little bit of speed up-and-up enough.
@@theebikeguy3852 thanks, but if i change p05 to 5 levels its not working, the bike then speeds up to 25km/h in every mode. If i set p05 in 3 levels i can choose 15-20-25 km/h.
I got E10 straight away 😅 ,still works but i thought it was compatible with KT esc's/controllers ,i should have bought the kt7 the kit came with but i went cheapskate 😅 🇬🇧
So looks like this display is not compatible with my controller (48V22A Lishui Sine-wave) there were kd21display on the bike. Or is there a way to fix that?
@user-iy7tj7hj2t The controller and LCD are programed together, in most cases you need to buy the same display you had, Even if you're able to make another display work with it, it's likely you will have issues..
@@methodes8911 Check the USB cable: A defective USB cable can cause display problems. Check the sensor magnet: A shifted sensor magnet can cause display problems. Check the fuses: A blown fuse can cause problems with the speedometer. Check the wiring and connectors: Inspect the wiring and connectors associated with the speed sensor, speedometer cable, or VSS for any visible damage.
i got a problem with it ... if i let go the throttle at high speeds then after a couple of seconds again try to push the throttle itll jerks like youre pulling on the brakes????
Could be the throttle, or possibly a break inhibioter acting up, If you disconnect both breaking heaviers depending on the style of E bike or E scooter, maybe only one see if you still have the same. Issue if you do, it's possibly a partly defective throttle. Like a it's like a piece of plastic that has broken inside and the Spring is getting stuck in a specific position. Not allowing it to function properly or the hall center is acting weird. Usually a error code will be associated with it but not always
@amirhoseinkargar3733 that would be the motor or possibly controller,,,,, if you put the back wheel off the ground and spin the tire slow with hand on it forward then backwards, if I feels kind of jerky, open up the unit, see if the 3 phase wires are melted together. If not disconnect the Hall sensor check your prongs for bent conecters or Corrosion?, If everything looks good, plug it back up. If you have the high go connector style line the 2 arrows up on either side. If it is just a quick disconnect, it's obvious how it snaps back together. Get back with me after you do this. If you find nothing, do not put it back together, I'll tell you how to run a test on the motor.
@@theebikeguy3852 i checked the resistance between phases before ...thyre all the same. the motor is 100 percent ok im sure of it ... it works .. i turn on the setup and start riding the vehicle daily...but every day i have this issue and after it e7 shows up
@amirhoseinkargar3733 OK, so you also tested the 3 phase wires while spinning the motor I guess? I would suspect that you would have a faulty controller. As the capacitors warm up inside, it probably starts acting up. Or one of the mosfits cold be going south..... But again, sometimes it's harder to diagnose unless it's directly in front of you. Hope some of the information I've given you helps. If not, good luck with the project, I'm sorry you're having issues with it.
@@OscarReyes-l4f If you bought the controller specifically for that unit, it will already be pre. Programmed. If you just bought a random controller, you will also have to replace the LCD display because they will be married together, and information will be shared between the controller and lcd display. That exact thing being in front of me. I'm sorry but I can't tell you.
@@raydoyle585 If I recall you have to hold the power button down for a few seconds after installing the numbers and it should go into the advanced settings
Communication error between LCD and Controller, you can check P20 to 0 and if it will work, First try to unplug lcd from.controller make.sure there are no bent pins then reconnect
@@theebikeguy3852 i did ...but i noticed something ...theres a rear led that comes from controller ....at start up they glow but i accidentally shorted them and now they stoped glowing ... is it the whole controller board or what?
@@amirouw OK, well, I think you're referring to the rear tail light. It is possible for certain things to be working and others not to be and the controller to be partly burnt up. It's hard to say in your case without actually running test on it and without it being in front of me. Well well obviously I can't run test. Or it could have been that you burnt out the lights. It's hard to say. If you have a electric bicycle shop nearby, I suggest that you take it there. Sorry, you're having a difficult time with it.
Bro today on My Bicycle Display want password but i don't know which is password you can help Me which password i give then open my Bicycle Display Thnx
@DARSHANDEORUKHKAR faulty Controller, You may. Try to disconnect the controller from the display. Then reconnect it. If it's still showing area code nine replace the controller.
Is there a way to program the speed limits for each assist level? My ebike came with this display and it has 3 levels of assist which are programmed to be at 5 mph, 10 mph, and 15 mph. I would like to adjust this to be closer to 10, 15, and 20. Do you adjust the max speed and number of assists and does it just evenly divide the max speed by the number of assist levels you set it to? Also, my display is frozen and will not allow me to adjust certain settings. It is not password protected. It's odd!
Change PO5 from 3 to 5 this will alow more speed options, there is no setting each level, but by going to 5 levels that may get you where you want to be also make sure p08 is at 100.
@@theebikeguy3852 thanks!
If i change it to 5 levels it does'nt work, in every mode de bike wil going 25km/h.
The problem is, i can't drive slower then 15km/h if the motor is on. How can i fix this? The bike is deliverd without a trottle. I hope that you can help me.
Go.
To p 05 and change it to 5 pedal assist mode. This will pretty much get you. What you're asking for that's the only way you're going to get that little bit of speed up-and-up enough.
@@theebikeguy3852 thanks, but if i change p05 to 5 levels its not working, the bike then speeds up to 25km/h in every mode. If i set p05 in 3 levels i can choose 15-20-25 km/h.
I got E10 straight away 😅 ,still works but i thought it was compatible with KT esc's/controllers ,i should have bought the kt7 the kit came with but i went cheapskate 😅 🇬🇧
So looks like this display is not compatible with my controller (48V22A Lishui Sine-wave) there were kd21display on the bike. Or is there a way to fix that?
@user-iy7tj7hj2t The controller and LCD are programed together, in most cases you need to buy the same display you had, Even if you're able to make another display work with it, it's likely you will have issues..
Hi, is there a way to adjust it to prevent it from jerking a lot?
I’m using an E-Bike
Set P-12 to 1 it will take off smoother.
Where did you get the list of error codes???
I am a 12yr. Ev tec got a lot of them memorized, as soon as I'm off work I will look on our computer to see if I can find it and post a PDF.
Mine doesnt say How fast i go
manuals.plus/lcd/s866-lcd-instruments-v1-0-operating-manual@@methodes8911
@@methodes8911 Check the USB cable: A defective USB cable can cause display problems.
Check the sensor magnet: A shifted sensor magnet can cause display problems.
Check the fuses: A blown fuse can cause problems with the speedometer.
Check the wiring and connectors: Inspect the wiring and connectors associated with the speed sensor, speedometer cable, or VSS for any visible damage.
How to reset hitway bk3s
@@36July-g5y you can try this
th-cam.com/video/BCF7s_feZ4g/w-d-xo.htmlsi=qCWv4I6V-O02Ua-C
i got a problem with it ... if i let go the throttle at high speeds then after a couple of seconds again try to push the throttle itll jerks like youre pulling on the brakes????
Could be the throttle, or possibly a break inhibioter acting up, If you disconnect both breaking heaviers depending on the style of E bike or E scooter, maybe only one see if you still have the same. Issue if you do, it's possibly a partly defective throttle.
Like a it's like a piece of plastic that has broken inside and the Spring is getting stuck in a specific position. Not allowing it to function properly or the hall center is acting weird. Usually a error code will be associated with it but not always
@@theebikeguy3852 yeah its an E7 ..now why is that
@amirhoseinkargar3733 that would be the motor or possibly controller,,,,, if you put the back wheel off the ground and spin the tire slow with hand on it forward then backwards, if I feels kind of jerky, open up the unit, see if the 3 phase wires are melted together. If not disconnect the Hall sensor check your prongs for bent conecters or Corrosion?, If everything looks good, plug it back up. If you have the high go connector style line the 2 arrows up on either side. If it is just a quick disconnect, it's obvious how it snaps back together. Get back with me after you do this. If you find nothing, do not put it back together, I'll tell you how to run a test on the motor.
@@theebikeguy3852 i checked the resistance between phases before ...thyre all the same. the motor is 100 percent ok im sure of it ... it works .. i turn on the setup and start riding the vehicle daily...but every day i have this issue and after it e7 shows up
@amirhoseinkargar3733 OK, so you also tested the 3 phase wires while spinning the motor I guess? I would suspect that you would have a faulty controller. As the capacitors warm up inside, it probably starts acting up. Or one of the mosfits cold be going south..... But again, sometimes it's harder to diagnose unless it's directly in front of you.
Hope some of the information I've given you helps. If not, good luck with the project, I'm sorry you're having issues with it.
Hi there I bot A new controller bike and how can I set the controller it's A U 1
@@OscarReyes-l4f If you bought the controller specifically for that unit, it will already be pre. Programmed. If you just bought a random controller, you will also have to replace the LCD display because they will be married together, and information will be shared between the controller and lcd display. That exact thing being in front of me. I'm sorry but I can't tell you.
Can you tell me why mine only goes to P0 4?
@@jonvaughn123 It depends on the bike company. When they order in bulk , they may only have that many settings In their computer.
@@theebikeguy3852how unlock all settings or reset to factory?
@vidik79 Sorry To my knowledge today, LCD display of this type cannot be factory reset.It can only reset the mileage to 0
@@theebikeguy3852 that kinda sux lol
@@theebikeguy3852 wonder if it can be reprogrammed?
Mine asks for 4 digit code when I press + and - together? 🤔
You can try 3745
@@theebikeguy3852
Thanks typed in the number you suggest but it doesn't do anything, there's no enter button to enter the code 🤷♂️
@@raydoyle585 If I recall you have to hold the power button down for a few seconds after installing the numbers and it should go into the advanced settings
6262
1212
hi why i get E10?
Communication error between LCD and Controller, you can check
P20 to 0 and if it will work,
First try to unplug lcd from.controller make.sure there are no bent pins then reconnect
@@theebikeguy3852 i did ...but i noticed something ...theres a rear led that comes from controller ....at start up they glow but i accidentally shorted them and now they stoped glowing ... is it the whole controller board or what?
@amirhoseinkargar3733 what kind of bike you got that has lights on the controller
@@theebikeguy3852 led on the back of the bike are connected to controller board
@@amirouw OK, well, I think you're referring to the rear tail light. It is possible for certain things to be working and others not to be and the controller to be partly burnt up. It's hard to say in your case without actually running test on it and without it being in front of me.
Well well obviously I can't run test. Or it could have been that you burnt out the lights. It's hard to say. If you have a electric bicycle shop nearby, I suggest that you take it there. Sorry, you're having a difficult time with it.
I need a code
You can try 3745 or the devil+1. 6666
Bro today on My Bicycle Display want password but i don't know which is password you can help Me which password i give then open my Bicycle Display Thnx
why do i get E-09 error
@DARSHANDEORUKHKAR faulty Controller, You may.
Try to disconnect the controller from the display. Then reconnect it. If it's still showing area code nine replace the controller.