You are very welcome. I’m glad you love my channel! I’ll try to keep everything very basic and simple to comprehend. I appreciate you watching. Good luck with your project!
Hi, thank you for the helpful video! I have a question about keeping corner bead level and plumb when the drywall is not installed in good condition -how can I ensure it stays really straight? I find it hard to use a laser level every time I work on corner beads in Condo and townhouse unit. I’d really appreciate any advice you can give me about leveling without using the laser. Thanks from Toronto!
Hi, I am trying to replace some water damaged drywall in the bathroom. The piece is about 16"x3 1/2". One side buts up against an acrylic tub and just floats over the flange. The other side runs under a now partially rusted corner bead. I rent, so I am not going to replace with tile or Hardiebacker. I am just trying to figure out if I can get a 16" replacement piece of corner bead to match the profile of the undamaged portion of corner bead that is still on the wall, or will it be a fools errand? Can i replace just the bottom portion of bead with vinyl to prevent rust? Will that make it harder to match? 2nd Can I run mud directly over the flange into the side of the tub, or do i need something like a Trimtex tearaway bead to prevent mud from cracking overtime due to temp fluc. and the mov. of the acrylic tub. I was honestly thinking of using a piece of pvc baseboard instead of drywall for a patch, so I take care of the waterproofing issue. But that's just because I'm forced to buy an entire sheet of Green Board when I am using less than a square foot. Thanks in advance for any advice.
It never does get covered in mud. You typically just paint over it. The metal corner is embedded in the mud for the most part except for the very corner. I hope that helps!
A: do all your taping 1st. B: start in the middle and use nails C: tape the corner to prevent cracks D: mud from the bottom and work up E: get rid of the gloves.
When it comes to teaching carpentry, you're my favorite.
This comment really does make my day! I appreciate that. I really do enjoy teaching through TH-cam videos. Stay tuned for more!
I approve your message
👌👍
I love this channel. You explain every detail making the process so easy to understand and implement. Many thanks 👍
You are very welcome. I’m glad you love my channel! I’ll try to keep everything very basic and simple to comprehend. I appreciate you watching. Good luck with your project!
That channel makes me save a lot of money, I learned a lot. Thank you so much.
Your job is always wowed. Thank you for all your videos
You’re welcome. I’m glad you are finding value in my content. I’ve tried to upload every week or so. Stay tuned for more!
Nice job and excellent production quality! -Ed
@@MyClutteredGarage Thank you Ed!
Good video. We use Mesh tape on the corner bid between metal and sheet rock to prevent future cracking.
That sounds like a great way to add security. Good idea. Thanks for sharing!
Excellent, thanks man
I appreciate that. You are welcome!
Thanks buddy, first time doing that
Hi, thank you for the helpful video! I have a question about keeping corner bead level and plumb when the drywall is not installed in good condition -how can I ensure it stays really straight? I find it hard to use a laser level every time I work on corner beads in Condo and townhouse unit.
I’d really appreciate any advice you can give me about leveling without using the laser. Thanks from Toronto!
I usually start from the center instead of at an end to prevent fold ups
You should make a video on how to frame the corner of a room
This video I made in the past might help
th-cam.com/video/JkplFW7WHRw/w-d-xo.html . Thanks for watching!
@@TheExcellentLaborer yea thank you keep up the good work love your videos very helpful
How did you mud those beads that were closer than 9 inches?
Hi, I am trying to replace some water damaged drywall in the bathroom. The piece is about 16"x3 1/2". One side buts up against an acrylic tub and just floats over the flange. The other side runs under a now partially rusted corner bead. I rent, so I am not going to replace with tile or Hardiebacker. I am just trying to figure out if I can get a 16" replacement piece of corner bead to match the profile of the undamaged portion of corner bead that is still on the wall, or will it be a fools errand? Can i replace just the bottom portion of bead with vinyl to prevent rust? Will that make it harder to match?
2nd Can I run mud directly over the flange into the side of the tub, or do i need something like a Trimtex tearaway bead to prevent mud from cracking overtime due to temp fluc. and the mov. of the acrylic tub. I was honestly thinking of using a piece of pvc baseboard instead of drywall for a patch, so I take care of the waterproofing issue. But that's just because I'm forced to buy an entire sheet of Green Board when I am using less than a square foot.
Thanks in advance for any advice.
How does the corner get mud if its scraped off?
It never does get covered in mud. You typically just paint over it. The metal corner is embedded in the mud for the most part except for the very corner. I hope that helps!
A: do all your taping 1st. B: start in the middle and use nails C: tape the corner to prevent cracks D: mud from the bottom and work up E: get rid of the gloves.
Where do you live ?
Sorry……. 76yo didn’t have my glasses on…. I thought the title was Corn Bread……
If you spread joint compound on your corn bread you won't need to use tooth paste ever again.😝
You guys are my kind of people 😂
🤣
😂😂😂