How To Change 2017 - 2023 Chrysler Pacifica Cabin Air filter - Replace Remove Replacement Location

A video tutorial on how to replace the cabin air filter on a 2017 - 2023 Chrysler Pacifica.
WHEN SHOULD YOU CHANGE THE CABIN AIR FILTER IN YOUR CHRYSLER PACIFICA?
It is recommended that you replace your cabin filter every 10,000 - 15,000 miles or once a year.
If you need to remove, replace or change the cabin air filter in your Chrysler Pacifica you should perform the following steps:
1. Open the glove compartment door partially, leaving extra slack on the glove compartment tension tether. Detach the glove compartment tension tether by sliding the black tension tether clip down, and popping it out of the slot on the side of the glove compartment door.
2. There are glove compartment travel stops on either side of the glove compartment door. To release them, push inward on each travel stop, and pull the glove compartment door down until the travel stops pass clear of their hooking points..
3. Pry up the lid of each individual compartment snap, and detach it from the rest of the snap. There is a small space on the side of each snap to use for separating the lid
4. After removing the snaps, lift up the compartment cover to gain access to the fresh air inlet location.
5. Remove the cabin filter cover by prying back each of the retaining tabs from their hooking points, and then pulling the cabin air filter cover out to expose the cabin filter. Remove the cabin air filter by pulling it straight out of the housing.
6. Install the new cabin air filter with the arrow on the filter pointing toward the floor.
7. Once the Cabin filter is replaced, Reverse steps to complete
This video tutorial will show the location of, as well as how to change, remove or replace the cabin air filter on the following Chrysler Pacifica models:
2017 Chrysler Pacifica ( L, LX, Touring and Limited )
2018 Chrysler Pacifica ( L, LX, Touring and Limited )
2019 Chrysler Pacifica ( L, LX, Touring and Limited )
2020 Chrysler Pacifica ( L, LX, Touring and Limited )
2021 Chrysler Pacifica ( L, LX, Touring and Limited )
2022 Chrysler Pacifica ( L, LX, Touring and Limited )
2023 Chrysler Pacifica ( L, LX, Touring and Limited )

[@41448023]

This guy is so easy to understand he's straight to the point on how to fix the problem

[@DanielStaggs]

This was made perfectly for someone doing this the first time. Very well made video.

[@tjs4813]

Well done! Clean, concise, and helpful with all the lil Chrysler quirks

[@willonthewing2860]

Thanks for the video. You showed releasing the clip on the right side, but you must also release the clip on the left side in the same way, or you are likely to break the clip on the left side (as I did). If you do break one of the clips (which seems likely to occur at this or a later change), you can use a couple of good rubber bands wrapped from left-to-right across the front to hold the cover in place.

[@maxshrike]

Straight to the point, excellent job describing the process

[@haydendoan7691]

Thank you. This is the best video of the ones on TH-cam!

[@aquilinobenitez5055]

Best video on this process yet. Thanks

[@kenboi169]

Great explanation video. Well done. One Caution though is when removing the elastic dampening cord (30-second point), don’t just let the cord spring back as shown in the video. My bad luck had the connector piece drawn back and got caught on something behind the plastic frame. It took about 45-minutes of frustration retrieving it. Best to unhook the dampener from the glove box and gently let it retract to its resting point while holding it. Otherwise about a 10-minute process to complete.

[@mikevv7542]

Very helpful… our filter is now replaced thanks to you!

[@marcia.1463]

great job explaining thank you

[@SmokinLoken]

Don't just pull on the push pin. You'll break it. When removing the cover, push the center of the push pin in and the entire thing will come out easily. When putting the cover back on, push the center of the pin out (opposite direction from before) and you can easily secure it in the hole.

[@briangarvey6895]

Made the process simple and easy. A great video. Thank you very much for posting this.

[@manasseh7487]

Thank you for the instructions. Very helpful!

[@tracybaumann4130]

Extremely helpful. Thank you!

[@dakshots]

excellent demonstration. Thank you!

[@marciastanton-vr7ml]

Very helpful! Thanks for all the details.😊

[@JiveTurkeyAndMe]

Perfect video.. absolutely perfect!

[@kenhugen285]

Very helpful! Thanks for a great video!

[@djrosa773]

Awesome, thank you so much for the great video I really appreciate it I'm doing that today it's guys like you that keep us all rolling man thank you

[@genebinion]

Appreciate your information! Thank you!