Rusty Panel Car Door Repair #mechanic #automechanic #automobile #cars #trucks #restoration #mechanicsteve Join as a member to support me : ) / @mechanicsteve
you were supposed to blend in the driver's door as well as a former bodyshop painter it is the correct way and I wouldn't have added bondo to the door again. best results are to replace the door panel skin..
Ремонт заслуживает одобрения, только вот одно "но", характерное для большинства автосервисов: не закрывают проем соседней (передней) двери. И после ремонта, владельцу автомобиля придется-таки обратиться к дейтелингу! Это называется культурой производства. Независимо, какими работами ты занимаешься, кузовными, малярными или установочными!
So after you stripped it down to bare metal, was that an epoxy primer you sprayed over it? And then you put the filler on top of that? I’ve read where some prefer to put the filler directly on the metal then epoxy over that. I would think the epoxy primer seals the metal to prevent future rusting?
Отверстия надо заваривать или оловом лудить. Шпаклёвка как губка воду впитывает. Через эти, казалось бы маленькие дырочки, проникнет много воды и шпаклевка снова треснет. А железо заржавеет.
That's exactly what happens when you put mud over bare metal it rusts the metal and you don't even know it until you have to go back and do a repair and then you discover the metal once you peel the mud off
Buenas noches colega mis más sinceros saludos y respetuosamente le digo mi opinión yo cambiaría la puerta Ho el lienzo para más rap y se lo aria ver al cliente y le queda mejor y se vería el carro con su linia exacta
Данное видео показывает как не надо делать. Всё что сделано это грубое нарушение технологического процесса. Почему до этого произошло отслоение шпатлёвки. Отверстия после споттера нужно было заварить сваркой что бы не допустить доступ воздуха и влаги. Грунтовать перед нанесением шпатлёвки нужно первый слой кислотный грунт второй акриловый. Шпатлёвки на больших плоскостях работают рубанком а не орбитальной. В результате через не большое время дверь бутет такой же какой и была. Так что делать вот таким образом нельзя. Материал и труд на ветер😢
É preferível trocar a porta do fazer um porcaria....não é pizzaria q só tem mta massa... Aqui q capaz de fazer são pintores q trabalham p lojista...q é famosa carioca...ou um garibada..
That repair is going to fail again. The best thing was to replace the door or put a new skin on it. But if its a budget repair at least lightly sand blast the rusty crevices .Tack weld all the holes and apply all metal or fiberglass filler before bondo. Please do better
I don't like your project. You should change whole panel and rest treate it before monting on the car. Norwegian de ter and panter do this way. Don't mind my comment
Работы много, и толка нет, всеровно дверь уже мусор, я бы просто поменял!)
And this is why you always take a magnet when buying a used car.
you were supposed to blend in the driver's door as well as a former bodyshop painter it is the correct way and I wouldn't have added bondo to the door again. best results are to replace the door panel skin..
Ремонт заслуживает одобрения, только вот одно "но", характерное для большинства автосервисов: не закрывают проем соседней (передней) двери. И после ремонта, владельцу автомобиля придется-таки обратиться к дейтелингу!
Это называется культурой производства. Независимо, какими работами ты занимаешься, кузовными, малярными или установочными!
“Bondo” Wagon coming up! Again… 😂
Badly in need of a new door skin !!
Just get another door from a scrap yard
Uau.
Very well done .
Great job.
Good job but it would’ve been better to find another door and faster
Kerja yang sangat bagus,super cepat rapi dan sempurna..
Your videos They help me a lot
That would be the correct way to repair a door ...but the correct way would be a new door skin ...or a second hand door not put pud on a door.
Muy bien video ,cuánto que se aprende con ellos muchas gracias.
New door skin
New friend welcome very nice video
Holy crap people still use mud, I haven't seen that since the late 90s.
El problema radica en que tiene mucha masilla se agrieta y se mete el agua oxida la chapa y salta la masilla yo cambiaria la puerta entera
Would have been easier to get another door.
То ли это будет машина, толи это будет клад( сокровищ)😎
New door skin might help ffs!!🤔🙄
Using a screwdriver correctly yeah!!🤔🙄
A sweetheart of a job!
So after you stripped it down to bare metal, was that an epoxy primer you sprayed over it? And then you put the filler on top of that? I’ve read where some prefer to put the filler directly on the metal then epoxy over that. I would think the epoxy primer seals the metal to prevent future rusting?
Excelente.....mas será q essa ferrugem não vem de dentro pra fora?
Não era melhor troca a folha de porta?
Tbm pensei a mesma coisa.
А че нельзя нормально выпилить рубанком, что бы ровно было?
А зачем, это пособие по замене старой шпаклёвки на новую?
Dude I'm sorry but I have to agree with them I would either get another door or at least another door skin
Think you could afford a larger blade to remove the bonds.
Отверстия надо заваривать или оловом лудить. Шпаклёвка как губка воду впитывает. Через эти, казалось бы маленькие дырочки, проникнет много воды и шпаклевка снова треснет. А железо заржавеет.
Механик Стив вмятины только пластилином выпрямлять умеет?
Ежегодная замена шпаклевки?!
W Polsce takie używane drzwi można kupić do 300 złotych, za taką robotę to minimum 900 złotych, dobra robota ale to zależy od kraju czy się opłaci
Первый раз наверное он же делал 😂😂😂
Latoneria con martillo silencioso😂
Цвет вообще не сошелся 😅😅 подборщика краски на мыло! 😂😂
Ну,… пойдет, особенно если спиной смотреть. Жаль в цвет не попали. Я так понял, что там на пофиг всем.
That's exactly what happens when you put mud over bare metal it rusts the metal and you don't even know it until you have to go back and do a repair and then you discover the metal once you peel the mud off
Тот случай когда заставили переделать работу
А чем прошел после зачистки первый слой? Грунт какой-то?
Заменить дверь дешевле.
*لم تقم بتنعيم الطلاء بواسطة البوليش بعد جفاف الطلاء ليتطابق الطلاء الجديد مع القديم* 🤔
I will apply one layer of body fiber first then apply body putty it last longer
Absolutely crazy that they don't sand in-between coats
Buenas noches colega mis más sinceros saludos y respetuosamente le digo mi opinión yo cambiaría la puerta Ho el lienzo para más rap y se lo aria ver al cliente y le queda mejor y se vería el carro con su linia exacta
Good job 🎉🎉🎉
Должна походить теперь! Только сильно дверью не хлопай!
العمل المطقن جميل 😮😮😮
Be easier to get a replacement door
Лучше было бы дверь поменять, шпакля долго не будет держаться, потрескаются всеровно.
Блает почистил мсташку заново ставку зделоеш единство свежи😂
Данное видео показывает как не надо делать. Всё что сделано это грубое нарушение технологического процесса. Почему до этого произошло отслоение шпатлёвки. Отверстия после споттера нужно было заварить сваркой что бы не допустить доступ воздуха и влаги. Грунтовать перед нанесением шпатлёвки нужно первый слой кислотный грунт второй акриловый. Шпатлёвки на больших плоскостях работают рубанком а не орбитальной. В результате через не большое время дверь бутет такой же какой и была. Так что делать вот таким образом нельзя. Материал и труд на ветер😢
A massa poliéster não criou vínculo com a lata... Sorte !!! Agora pagar outra mão de obra... Mais gastos
Do these guys distinguish colors at all?
в вашей шпаклёвки металла не найдено
É preferível trocar a porta do fazer um porcaria....não é pizzaria q só tem mta massa...
Aqui q capaz de fazer são pintores q trabalham p lojista...q é famosa carioca...ou um garibada..
Pero es mejor pelar la puerta entera con removedor
Maşallah
Shade not match with last one..gloss issue as compared old paint
Я бы ещё отпескструил и обезжирить.
Hizo lo mismo que tenía..... mal trabajo
❤❤❤❤❤❤
👍👍👍
That repair is going to fail again. The best thing was to replace the door or put a new skin on it. But if its a budget repair at least lightly sand blast the rusty crevices .Tack weld all the holes and apply all metal or fiberglass filler before bondo. Please do better
そもそも、何故パテ割れして錆びたのか⁉️考えて欲しかったなぁ😢
こちらで考察すると、厚盛りパテした事で弾力性に欠け、表面が割れて水の侵入を許してしまった😮のが原因かと。
となると、鋼板の表面を板金で平すか⁉️パテより弾力性があるボンドで平すか⁉️した上で、防水対策したら良いと思いますが、いかがでしょうか⁉️😮
😮 non va bene lavoro fatto molto male
Why not replace the door plus you missed the rear pillar you got most of it but left a big dry spot
Hack. Didn’t fix why it rusted. Really, the door should be replaced or reskinned.
Полное дерьмо
I don't like your project. You should change whole panel and rest treate it before monting on the car. Norwegian de ter and panter do this way. Don't mind my comment
The owner must be poor. Can't afford to pay for a proper repair
You can see where he missed with the clear on the "C" pillar.
Jako robotę to na 5, ale po co tego złoma naprawiać? jak można wymienić całe drzwi i to w kolorze.
Фуфло а где рихтовка?
Отвалится через год,толстый слой шпакли...