इसी तरह से डायग्राम के साथ इन्वर्टर के हर भाग का फाल्ट समझाकर वीडियो बनाएं सर जी ड्राइव सेक्शन चार्जिंग सेक्शन ओवरलोड लो बैटरी आउट पुट सारे भीभाग की वीडियो कितनी भी लंबी हो thanku sar
Sir Koi jawab nhi apka Bahut Shandar Samjhate h aap Very very thanks sir Dil khush hogya or ek bat bata pehli bar Kisi yutuber ke muse sach bat suni h ke Ke dosto esa TH-cam par koi nhi batayega bilkul shi bola sir koi nhi batayega Ese sb sale chutya cut te usse achha h video banaye hi nhi
Pure TH-cam par Aaj Tak sbse sandar vedeo dekhne ko mila,,,ye video aapko aatmnirbhar bnata hai ,,,khud ke andar ek kabiliyat paida karta ha ,,,,,,,nahi to lakho video aapko mil jayenge,,,ye fault hai ye badal do,,ye khrab hai bas yahi chal Raha hai,,,,,,,,shinewave par bhi video banaye mitar
सबसे पहले तो आपको मेरा प्रणाम सर बस आप इसी प्रकार अपना support बनाए रखना मै सारे fault कर ऊपर video banaunga || आप अगर चाहे तो online course के माध्यम से हमसे जुड़ सकते है उसमे मै हर एक fualt को diagram कर माध्यम से समझाता हु
Sir aaj toh aap ne kmaal kar diya hai, sir issi tra alg-alg section ki video banate raho, sir harek kitt per ek series bnayo, sir video circuit diagram ke sath hi banaya karo, sir hum bi aapki mehnat ka mull moda ge, Dil se dhanyawadh, sir diagram zoom Karke screenshot ka time zarur diya karo, thanks
Bhai vedio mast bnai hai.. Pure TH-cam per nhi 100% bhai ek problem hai drive voltage ko lekar.. Agr microcontroller ic per 28 27 per 0 voltage ara hai toh kya krna chahie please reply bro.. 😢❤
Thank you sir ji Jo aapne mujhe is kabil samjha Dekhiye agar microcontroller ki pin number 27 or 28 se drive volt out nahi ho rahe to drive section me lage transistor or rasistance ko check kare kyoki mcu kharab hone ke chance kebal 10% h Or microcontroller ko check karne ke uski 27 or 28 number pin ko open kar le fir check kare Diagram ke according
@@dushyantelectronicsbhai microcontroller ic nikalne ke baad bhi nhi show hora only 0 volt transistor okk hai sb battery lagte h relay open hone ka sound ara h but beep krke on nhi hota sukam 850 board h bhai
I am learning to repair inverter. Thanks sir, for this indetailed video on square wave inverter, Wactched this video many times whenever microtek square wave inverter comes for repair. I have microtek 625 E2 model, micro IC and 4 mosfet fault so changed it. switch on, I am getting driver volt 1.8v at 27 and 28 pin, led status "inv led" glows all Eight MOSFETs Gate are getting 4V but no volt in drain or source also no AC volt generate in both TX channels. checked all resistors, transistors and diode. What is the AC volt generate at TX channels by check with multimeter in AC mode ? DT830 multimeter can able to mesure square wave voltage ?
As far as I am able to understand your problem, your Microtek square wave inverter is not producing AC voltage, then you can replace the diode at the location of D7 and D8 and the 50 v 470 uf capacitor, your problem will be solved. 
@@dushyantelectronics First of all, Thanks for your reply.Replying to subscriber's comments are rarely happens.Thanks again and I will check those diode and will reply.
Brother ji, circuit diagram ka screen shot lene ke liya zom karya kare, dikhai nhi deta, brother ji, luminous zellio ki ek series bnayo, alg-alg section ki circuit diagram ke sath, bahut achhe se samjate ho, thanks brother
Bhai me bhi invertr riper karta hu mujhe aapki baat samjh agayi bhai ek microtek eb 700 sin wave invertr hai wo bettry full hone pr bhi low bettry pr chala jata hai or charjing cut bhi nhi ho raha hai kya karna chhye aap bataye bhai
Good afternoon sir, m fouji hu, but Ish kit ko mere inver m replace karna hai pura connectin pin wise Karna /diagram likhkar d'Alene ka Kasth karin, thanks... very much
बहुत ही सुन्दर, माइक्रोटेक EB900 स्क्वायर वेब इन्वर्टर में सेंसिंग ट्रान्सफर के पास mov खराब होने पर दूसरा लगाया वो भी फिर से 1 घण्टे में खराब हो गया, ऐसा क्यों हुआ?
Str microtek inverter me output volt AA Raha hai par jab usper load dete hai to uske volt baith jate hai jaise 250v se 50ya70 ke bich mai rah jate hai kya foult hoga please video bana ke samjhana
Sir mere inveter upse2 1115 model kah inveter mai ups on nahi hora hai sir light on hota hai but ups on nahi hora hai output vi nahi deraha hai charging and mainse ok hai back mode nahi chalraha hai plz sir bata dijya kya kare
Hello sir me mechanic hu inverter repairing shop hai .....mere pas 1 customer ka microtek ka eb1500 double battery ka inverter repair hone aya usme problem h drive volt 5.5 bn rhe h drain jese hi tight kr ke on krta hu kuch der chlega aur mosfet brust ho jate.2 bar mosfet change lr chuka dono br brust ho chuke h los hua mera drive volt kam kese kre Transistor jiner diod resistance sb naya lga diya fr bhi drive volt kam ni ho rha Pls sir help me
Sir,4 transistor ke pas 5 ragistanc laga hai,usme 2 10k, aur 2 1.2k hai ,jisme 10k ragistanc new laga deye to 4transistor mese 1 hit ho raha tha ,use bhi new lagaya phir bhi hit Raha hai,aur ager 1 10k ka rasistanc open kar Dene se hit hona ruk jata hai, AAP mujhe 10k ka use ke bare bataye , please
Sir 24 volt same kit me right side wala single 547 Jo mosfet ke paas hi uske base pr 2.3 volt Aa raha hi 547 hata dene pr drive ok ho Jaata hi kya kre?
Sir. Microtek 875 e2 inverter hai. Maine mosfet , (4 +1 ) 547 transistors , 4007 dono, c15 Ziner change kar diya, 1.2k resistance bhi check kar liya, diode se drain ki track bhi check kar liya. But channel 1 me drive voltage nahi ban rahi jab ki channel 2 me sahi hai. Ab samajh nahi aa raha kya check karu. Channel 1 me heatsink pe 1.17 volt bata raha hai jab ki nahi batana chahiye. Please koi sulution bata dijiye
सर मेरे माइक्रोटेक इन्वर्टर की pcb e2 प्लस है इस पीसीबी में मॉसफेट खराब हो गए थे जब मैं मॉसफेट पी 55 लगाए तो बैकअप मोड पर 300 वोल्ट आउटपुट देने लगा मैंने एनालॉग मल्टीमीटर से भी चेक किया वोल्टेज 300 रहा है जब उसमें मैं AC सप्लाई देता हूं तो चार्जिंग भी करता है और आउटपुट में 220 वोल्टेज देता है इनवर्टर बैकअप मोड पर 300 वोल्टेज निकल रहा यह प्रॉब्लम कैसे ठीक होगी प्लीज मुझे बताइए
देखिये भाई ये problem इस pcb में drive voltage से ही होती है आप drive से ठीक कीजिये और transformer के drain wire को ठीक से लगाइये problem जरूर solve होगा
सर मेरे इनवर्टर की पीसीबी e2+है जिसमें P1806 मॉसफेट लगे थे मॉसफेट खराब हो गए थे उसमें मैं P55 मॉसफेट लगाया तो आउटपुट 300 वोल्ट निकाल रहा है उसे कैसे ठीक करें
![CAMPปลิ้น | EP.79[1/2] แก๊งไทบ้านพาบุกเมืองบั้งไฟโก้ ยโสธรรรร!!!](http://i.ytimg.com/vi/Ldr3_fvTEXk/mqdefault.jpg)
Aap bahut hi acchi video banate ho good
इसी तरह से डायग्राम के साथ इन्वर्टर के हर भाग का फाल्ट समझाकर वीडियो बनाएं सर जी ड्राइव सेक्शन चार्जिंग सेक्शन ओवरलोड लो बैटरी आउट पुट सारे भीभाग की वीडियो कितनी भी लंबी हो thanku sar
Ok sir ji bas aap video ko pura dekhna
Bahut achha good explain
Good information veer ji ❤❤❤❤
Thank you so much sir awesome explanation ❤❤❤❤
सर जी आपका तर्क सबसे बढ़िया है प्लीज़ सर्किट प्लेट मे दिखाऐ तो और अच्छा होगा
Nyc explained sir ji
Good video sir
सर आप के समझाने का तरीका बहुत अच्छा है
Thanks sir ji
Thanks 👍 Bhai
Sir Koi jawab nhi apka Bahut Shandar Samjhate h aap Very very thanks sir Dil khush hogya or ek bat bata pehli bar Kisi yutuber ke muse sach bat suni h ke Ke dosto esa TH-cam par koi nhi batayega bilkul shi bola sir koi nhi batayega Ese sb sale chutya cut te usse achha h video banaye hi nhi
Thanks
Aap ne itni mahnat se video bnaya hai iske liye thanks 👍 sir Bina comments or liye kiye ham bhi nhi jane wale
Thanks sir ji bas aap apna support banaye rakhna
Bilkul sahi baat kahi apne 👍👍👍 diagrams se bahut madad milti hai
Very great job sir
Thanks sir
Thanks sir
Aap bahut hi acchi video banate ho sir thank you
Bahut aache se smjhate hain.। ❤❤❤
Thanks ji
Very good sir pura drive section dimag me beth gaya he ab to
Thanks
Nice video sir
Very good explain
Thanks
Very good ❤❤❤❤❤
Bahut achcha
Thanka
Thank you sir ji mara set ok ho gaya 😊🎉🎉❤❤❤
@@akhileshmorya3832 my pleasure
Good video🎉
Very good👍👍👍👍👍
Nice video sir thanks
Sir microtek e2 + ke mosfet ke track ukhad gaye hai uska circuit digram ho to upload kijeye thanks
Pure TH-cam par Aaj Tak sbse sandar vedeo dekhne ko mila,,,ye video aapko aatmnirbhar bnata hai ,,,khud ke andar ek kabiliyat paida karta ha ,,,,,,,nahi to lakho video aapko mil jayenge,,,ye fault hai ye badal do,,ye khrab hai bas yahi chal Raha hai,,,,,,,,shinewave par bhi video banaye mitar
सबसे पहले तो आपको मेरा प्रणाम सर बस आप इसी प्रकार अपना support बनाए रखना मै सारे fault कर ऊपर video banaunga || आप अगर चाहे तो online course के माध्यम से हमसे जुड़ सकते है उसमे मै हर एक fualt को diagram कर माध्यम से समझाता हु
महोदय अगर आफलाइन कोर्स है तो माफी चाहते हैं,,,क्योंकी हमारी खुद की दुकान है,,,समय कम मिलता है,,,,, और अगर आनलाईन है तो,,,जरुर विचार करेंगे,,,,,,
@@princeraj-wd4ve ji online hi h
Good
Nice sir ji
Nice information
Thanks sir ji
Very good sir
Sir app samjhate to bahut achha hai lekin app ek bar fir se shuru se bataiye jaha se men lid shuru hoti hai
Ok sir
Sir aaj toh aap ne kmaal kar diya hai, sir issi tra alg-alg section ki video banate raho, sir harek kitt per ek series bnayo, sir video circuit diagram ke sath hi banaya karo, sir hum bi aapki mehnat ka mull moda ge, Dil se dhanyawadh, sir diagram zoom Karke screenshot ka time zarur diya karo, thanks
Thanks sir ji
Charging kese hota he ye bhi video bana ke yese dikha do. THANKS
Or mere bhai Jitne log Sir ko dekh re wo Like Shere or Subscribe zroor kare
Sir koi luminous eco watt walo ki videos add kar dijiye ❤
Brother ji, screen shot lene ke liya kuz time video ko rok ke rakhya karo, achhi tra dikhai nhi deta, thanks brother
Bhai vedio mast bnai hai.. Pure TH-cam per nhi 100% bhai ek problem hai drive voltage ko lekar.. Agr microcontroller ic per 28 27 per 0 voltage ara hai toh kya krna chahie please reply bro.. 😢❤
Thank you sir ji
Jo aapne mujhe is kabil samjha
Dekhiye agar microcontroller ki pin number 27 or 28 se drive volt out nahi ho rahe to drive section me lage transistor or rasistance ko check kare kyoki mcu kharab hone ke chance kebal 10% h
Or microcontroller ko check karne ke uski 27 or 28 number pin ko open kar le fir check kare
Diagram ke according
@@dushyantelectronicsbhai microcontroller ic nikalne ke baad bhi nhi show hora only 0 volt transistor okk hai sb battery lagte h relay open hone ka sound ara h but beep krke on nhi hota sukam 850 board h bhai
Sir ji pura microcontroller bahar nahi nikalna h sirf 27 or 28 number pin bahar nikalni h fir un par voltage check kijiye
1नबंर
I am learning to repair inverter. Thanks sir, for this indetailed video on square wave inverter, Wactched this video many times whenever microtek square wave inverter comes for repair.
I have microtek 625 E2 model, micro IC and 4 mosfet fault so changed it.
switch on, I am getting driver volt 1.8v at 27 and 28 pin, led status "inv led" glows
all Eight MOSFETs Gate are getting 4V but no volt in drain or source also no AC volt generate in both TX channels. checked all resistors, transistors and diode.
What is the AC volt generate at TX channels by check with multimeter in AC mode ? DT830 multimeter can able to mesure square wave voltage ?
As far as I am able to understand your problem, your Microtek square wave inverter is not producing AC voltage, then you can replace the diode at the location of D7 and D8 and the 50 v 470 uf capacitor, your problem will be solved.

I hope your problem will be solved


@@dushyantelectronics First of all, Thanks for your reply.Replying to subscriber's comments are rarely happens.Thanks again and I will check those diode and will reply.
Brother ji, circuit diagram ka screen shot lene ke liya zom karya kare, dikhai nhi deta, brother ji, luminous zellio ki ek series bnayo, alg-alg section ki circuit diagram ke sath, bahut achhe se samjate ho, thanks brother
Nice sir. Ham ko asi diagams kase milege
Sir ji pcb ko dekh kar banane padenge
Ok sir
Microtek square wave me ek traf drive volt sahi ban rahi hai aur ek traf low volt bann rahe kaise hoga
Agar solution chahiye to whatsapp kro
Sir microtek v7 inverter ki over lod or charging pe ak video banao
Ok
Microtek inverter ke online course me join ho jaiye usne sabhi fault diagram ke sath samjhaye jate h
@@dushyantelectronics ok sir
Bhai me bhi invertr riper karta hu mujhe aapki baat samjh agayi bhai ek microtek eb 700 sin wave invertr hai wo bettry full hone pr bhi low bettry pr chala jata hai or charjing cut bhi nhi ho raha hai kya karna chhye aap bataye bhai
Uski mico ki pin number 5 par volt check kare
Good afternoon sir, m fouji hu, but
Ish kit ko mere inver m replace karna hai pura connectin pin wise
Karna /diagram likhkar d'Alene ka
Kasth karin, thanks... very much
जय हिंद सर जी
आप 8192870833 पर whatsapp कर सकते है
only invarter ki video banaiye sir aur explane kigea sir
Sir mere pass jo repairing ke liye aata h uski video banata hu
Agar aap class me join hona chahe to ho shakte ho
बहुत ही सुन्दर,
माइक्रोटेक EB900 स्क्वायर वेब इन्वर्टर में
सेंसिंग ट्रान्सफर के पास mov खराब होने पर दूसरा लगाया वो भी फिर से 1 घण्टे में खराब हो गया, ऐसा क्यों हुआ?
देखिये सर mov high voltage से खराब होता है तो एक बार voltage चेक कीजिए
Str microtek inverter me output volt AA Raha hai par jab usper load dete hai to uske volt baith jate hai jaise 250v se 50ya70 ke bich mai rah jate hai kya foult hoga please video bana ke samjhana
Sabse pahle drive volt ko check kijiye drive volt to nahi daw rahe h
Sir mere inveter upse2 1115 model kah inveter mai ups on nahi hora hai sir light on hota hai but ups on nahi hora hai output vi nahi deraha hai charging and mainse ok hai back mode nahi chalraha hai plz sir bata dijya kya kare
Aap 8192870833 par whatsapp kare
Bhai agar ek side Kum or dusre side thoda zyada drive volt aae to kaise equal krenge???? Please answer
Dono side ek hi number ke mosfat lagaye. Or same value ki hi rasistance use kare
Step by step voltage chake kar ke bataye one side vovtalge nahi aa raha hai
Microtek inverter ka pura kam sikhne ke liye aap online class me jud sakte h
Sir 7545 mosped ki jagah p80 mosped lga sakte he ya fir koi or
Laga sakte h
Sir AAP hame expert Bana denge envetor ka
To bataiye kya karna hota
Kaise aapse hamesha support milta rahega
Sir ji mai puri puri kosish karunga ki aapko har ek video ko video ke माध्यम se samjha pau bas aap apna support banaye rakhna
@@dushyantelectronics
Ok sir thank you
Reply dene ke liye
Sir iss bord pe 100w lord thik chalta hai but ise jada lord dene me high amp leta hai aur out of instabl hota hai karan bataiye
Out put instabl hota hai
Mosfat konse number ke use kare h
मैंने चैनल को सब्सक्राइब कर लिया है ❤❤
thanks ऐसे ही support बनाये रखना
Hello sir me mechanic hu inverter repairing shop hai .....mere pas 1 customer ka microtek ka eb1500 double battery ka inverter repair hone aya usme problem h drive volt 5.5 bn rhe h drain jese hi tight kr ke on krta hu kuch der chlega aur mosfet brust ho jate.2 bar mosfet change lr chuka dono br brust ho chuke h los hua mera drive volt kam kese kre
Transistor jiner diod resistance sb naya lga diya fr bhi drive volt kam ni ho rha
Pls sir help me
Mosfat konse use kar rahe ho isme 10k or 100k ki rasistance ko check karo ye rasistance hi drive volt ko kam karti h
Sir aap konsa soldering iron use karte hai
Bhai siron ka 60w use karta hu
Sir please ek WhatsApp group mana please 🥺
Sir mere invetar e2pulas me daraw ok he rilye bhi ok fir bhi no output
Agar drive bhi ok h or relay bhi ok to ek rasistance ka fault ho sakta h
Sir npn transistor ke base par ground kaise de sakte hai
Kyuki collector par emitor se ground as Raha hai
Mujhe samjha nahi aaya samjhaye
Sir base par graund kha diya h
Mai transistor par complete video zaroor banaunga
Us video ke andar sab clear kar dunga
Sir,4 transistor ke pas 5 ragistanc laga hai,usme 2 10k, aur 2 1.2k hai ,jisme 10k ragistanc new laga deye to 4transistor mese 1 hit ho raha tha ,use bhi new lagaya phir bhi hit Raha hai,aur ager 1 10k ka rasistanc open kar Dene se hit hona ruk jata hai, AAP mujhe 10k ka use ke bare bataye , please
@@nehrumahto6982 10k rasistance ke madhyam se transistor ke base par supply diya h is transistor ke side ke sabhi zener ko check kijiye
Sir sukem ki micro par 27 or 28 par koi volt nahi ban rahe hai na mosped par drive a rahe hai digram ke jariye samgha de ple. Sir
Ok is topic pr video banaunga
Aap micro ki pin no 27 or 28 ki pin open kar ke check kare
Sir 24 volt same kit me right side wala single 547 Jo mosfet ke paas hi uske base pr 2.3 volt Aa raha hi 547 hata dene pr drive ok ho Jaata hi kya kre?
Is side me pf laga h use check karo or zener diode ko bhi
Aap kha se ho sir
Sir ak get pr jyada ak pr km driv mil rha h kya karan ho sakta bteye pl
Sabse pahle aap dono side ek hi number ke Mosfat lagaye or dono side 100 ohm ki hi rasistance lagaye drive dono side barabar milegi
All compny ka inverter course ka kitna payment krna hoga sir
बहुत सस्ते मे कराऊँगा
Parkash electric
Sab component chek krliye
Ek bar suru se components check kijiye jaise diagram me bataya h
10 9 8 7 pe kitini voltege aana chaiye oobhi batao logako
Pin number 7 par 0.8 volt main sense karne ke liye
Sir ji charging nahi kar raha hai 635t bhi sahi h ic26nopinse 2:5vbanraha h sab theek h fir bhi charging nahi ho raha h
Video send karo
Sir.
Microtek 875 e2 inverter hai.
Maine mosfet , (4 +1 ) 547 transistors , 4007 dono, c15 Ziner change kar diya, 1.2k resistance bhi check kar liya, diode se drain ki track bhi check kar liya. But channel 1 me drive voltage nahi ban rahi jab ki channel 2 me sahi hai. Ab samajh nahi aa raha kya check karu. Channel 1 me heatsink pe 1.17 volt bata raha hai jab ki nahi batana chahiye. Please koi sulution bata dijiye
Jabki. Microcontroller ic se 27 or 28 dono pin se voltage aa raha h
8192870833 whatsapp karo
Driver tansistor 547 charo open korne ke bad micro control se drive ata he. But tansistor conet cornese Sare drive drop
Zener check karo
Aap se judne kelie kiya karnahoga
8192870833 whatsapp karo
Drive volt aadhik aa raha hai
Sir dig.not lookig clear pl
Whatsapp number de do send kar dunga
Mereku daigram chaya kese payment karenge
Bhai m bahut jald hi online class shuru karunga fees bahut kam hogi
Sir muje sabhi diagram sahiye
Sabhi ke uper video banauga
Sir ek side drive nhi aa rha h
Sb change kr ke de liya
Kon si side channel 1 ya 2
8192870833 whatsapp karo pcb ki video
Ek drive me 1v Or dusre me 4v ban rahi hai kya karu sir
Sare zener check kijiye
सर मेरे माइक्रोटेक इन्वर्टर की pcb e2 प्लस है इस पीसीबी में मॉसफेट खराब हो गए थे जब मैं मॉसफेट पी 55 लगाए तो बैकअप मोड पर 300 वोल्ट आउटपुट देने लगा मैंने एनालॉग मल्टीमीटर से भी चेक किया वोल्टेज 300 रहा है जब उसमें मैं AC सप्लाई देता हूं तो चार्जिंग भी करता है और आउटपुट में 220 वोल्टेज देता है इनवर्टर बैकअप मोड पर 300 वोल्टेज निकल रहा यह प्रॉब्लम कैसे ठीक होगी प्लीज मुझे बताइए
देखिये भाई ये problem इस pcb में drive voltage से ही होती है आप drive से ठीक कीजिये और transformer के drain wire को ठीक से लगाइये problem जरूर solve होगा
Thank you@@dushyantelectronics
my EB 860 giving 310 volt . otherwise everything ok , what will be the booblem
@@bk7407 आप अगर मुझे inverter की video बनाकर send करोगे तो शायद मै आपकी कुछ help कर सकता हु
8192870833
सर जी दोनो चॅनल get पर 4.0 volt है . तो drive के कौन से Section में दिक्कत हो सकती है। R 74 से प्रोब्लेब हो सकता है क्या ।@@dushyantelectronics
Sir dygrqm kaise milega
Sir pcb ki help se banana padta h
Bro diagrams send bro
@@jayganpath7086 number do
Sir ek side nhi aa rahi hh
Call me 8192870833
Sabhi component theek hai fir bhi dry volt 2 volt se adhik Nahin mil raha hai pura ham card jaanch le resistance ke chhuda
Problem to rasistance or zener diode me hi h aap kha se ho
UPk baliya jile se hun Maine❤ Maine Maine registration se jinar bhi check lekin MOSFET per koi pals Bolt nahin mila aur ab chhod Diya hun
@@BihariLalprashad-gb6xu video banakar send karo 8192870833 whatsapp number par
सर मेरे इनवर्टर की पीसीबी e2+है जिसमें P1806 मॉसफेट लगे थे मॉसफेट खराब हो गए थे उसमें मैं P55 मॉसफेट लगाया तो आउटपुट 300 वोल्ट निकाल रहा है उसे कैसे ठीक करें
Analog ( sui ) wale Multimeter se check kijiye output thik hogi
एनालॉग मल्टीमीटर से चेक किया वोल्टेज 300 आ रही है ड्राइव वोल्टेज भी चेक किया था वह 5 वोल्ट आ रही है
Fi bhi sehi nhi hui
Kya problem h drive volt me
Book kitana ka hi
Bhai book koi nahi h online classes available h
Price kya h
22:42 23:39
Kya matlab sir
English namder
सर डायो ग्राम का बुक मिल सकता है क्या
Sir book to nahi milega
@@dushyantelectronics sr book nhe to PDF mele ga
@@amitchourasia9106 m provide karaunga
Pahele kuch practical Kar lijiye uske baad daigram banaiye
To aap hi bta dijiye
Aapne jo 4 transistor ka biasing samjaya wo galat hai.pahele khud acchi sa padai karo fir youtube ma dusro ko knowledgedena
@@user-xq6pb9fi6y mujhe ek baat samajh nahi aati tumhe kya problem h or agar maine galat bataya h to tum sahi bta do
Sir kisi bhi problem ke liye apna watsup no. Send kar do
8192870833
Aap bahut hi acchi video banate ho good