ฝัง
- เผยแพร่เมื่อ 20 ก.ค. 2024
- A comprehensive, step by step guide that goes through the process of installing new fascia, soffit, guttering, downpipes, gables, box ends and dry verge to replace existing ones.
0:30 - Stage 1 - Removing old roofline
1:33 - Stage 2 - Fitting new breather membrane and trusses
2:58 - Stage 3 - Fitting new soffits and joints
4:06 - Stage 4 - Installing new fascia boards
5:24 - Stage 5 - Installing new vent trays
6:25 - Stage 6 - Fitting new gutters and downpipe
8:48 - Stage 7 - Fitting gable end fascia & soffit
11:03 - Stage 8 - Installing Dry Verge
#buildingmaterials #construction #howto #installation #roofing #roofline #fascia #soffit #fasciatraining #fascias #rainwater #guttering #gutter #gutterinstallation #gutterrepair #gutters #gable #ventilation #felt #dryverge
To see our full range of products and services, visit our website: www.nbp.co.uk
Social Media
Facebook: / nbplimited
Twitter: / nbpltd
Instagram: / nbpltd
LinkedIn: / northern-building-plas... - แนวปฏิบัติและการใช้ชีวิต
Additional tip: run two string lines on the packers, one on the corner and another on the face edge or underside. This will make sure the packers are not just in line but also at a perfect right angle.
Personally I would not fix in the middle of the soffit with a polytop, this looks unsightly. Far better to pin with a cladding pin near the front edge where it is hidden by the fascia lip, and wedge the back down on to the top of the brick with and additional packer if needed. Obviously if the soffit butts up to the wall then a polytop is needed but closer to the wall where far less visible.
The state of that wart and silicone lmao
Great video. Thank you
love the gnd level scaffold :D
This is a very good video. Clear and informative detail. Well done.
Great video cheers. 👍🏆🇬🇧
Good video. Thanks.
Very good
Mans wart is the star of the show
William Ellis 6th finger
Cheapest verges and done wrong as well ment to strip cement verge out extend battens and nail verge into that
I’m glad they hired a professional voice over as their work is pish
State of the silicone
My thoughts exactly!
What the price like full guttering
Great video , however so many Health & Safety issues, e.g the way fascias are cut holding them in hand etc, I was scared just watching it
Totally agree.. pretty poor examples of how to work safely there …
Were they external screws? Nope.
Only apply glue to one side of the fascia trim so that you allow for expansion
Very good point, thanks for pointing it out!
Genuine question: there seem to be a fair few critics on the responses - can you please suggest a better video for replacing fascia and gutters on an older house? Cheers
You could take a look at our latest Fascia and Soffit fitting video here:
th-cam.com/video/EUPm-5Mbq-k/w-d-xo.html
Is Superglue suitable for outdoors where repeated exposure to moisture can soften it?
Silicone the best
They should have only glued one side of the joint to allow for expansion and contraction. Theirs will pop off eventually.
I wouldn't have posted this as an example of my work. That unsupported wavy soffit tells the story from 50 yards away.
so, there is no place for air intake? How about the breathing system for the attic area?
They installed vents,between the fasica and the tile tray
@@sopissedoff ok so it is underneath the gutter. Got it. Thanks!
@@chuckshu9662 no, it's above the gutter on top of the fascia boards. They sit under the eave trays
@@Landofhopeandglory575 I've seen this done, but why not just use vents on soffits?
Genuine question, not being picky. Shouldn't the rotten wood that supports the tiles have also been replaced as well as the membrane?
The wooden rafters do look to be in good condition still mostly and the installers in this case have strengthened them by attaching pvc flat fascia noggins to the rafter feet.
However, if some rafters have rotted, best practice is to cut back the affected area and bolt a new section of the same size treated timber to the rafter.
@@nbpltd Thanks for the reply. I was referring to the rotten wood sheeting that was removed with the membrane early in the video.
@@slowdown3787 Oh, we see now. Well, since the installers put a new breather membrane in, we don't believe it's necessarily essential for them to have put new wood sheeting in too. However, as we didn't undertake the job ourselves, it's hard to comment further on whether or not that was the best practice in this case.
Not sure about the look of the dry verge. Too chunky.
Shame about that silicone work at the end
Or just staple dpc to the back of the fascia
Tut tut tut ... dry verge fitted all wrong , oh dear
Where’s the Indian’s?
Was the customer expected to pay for that
OMG what a cowboy job. You are having a laugh aren't you?! All that felt scrunched up in a wad!
9:26 , 9:57, 10:04 🙁
This is a right crap job. State of that silicone !!
That dry verge will have come off in the first gust of wind. Poor.
9:26 and 10:03 stressed me out thought the guy was going to saw his hand off! Great video otherwise!!
Jesus christ. How to cover a beautiful old house in revolting plastic and tonnes of mastic. 🤯
Giving zero fucks about anything.