Could you possibly include this lab under NetSec v1.0 8.5.13 in the video description? Not a lot of people have the new NetSec version. Your videos are really helping me out with the walkthroughs.... onwards to ZPF !!!
@@romeroc24 hlo sir, can u help me In my project there are five department in bus topology. Like finance, testing, HR, manager, trainee. All are in different vlans with different IP address. I have all done apply vlans and all are communicating with each other. But there is requirement in my project that is manager department only should access finance department. All other departments should not access to finance department. Please send me commands which can be run in my project. I am totally fed up from internet . I have watched numerous videos but all are useless.
@@romeroc24 can u send me commands because I applied numbers of times with different patterns but it's failed. I think I am not able to understand that how to apply these commands. I tell u network address of every department. Finance-vlan10- 192.168.10.0/24 gateway- 192.168.10.1 Testing- clan 20- 192.168.20.0/24 Gateway- 192.168.20.1 HR- vlan30- 192.168.30.0/24 Gateway- 192.168.30.1 Manager- vlan40- 192.168.40.0/24 Gateway- 192.168.40.1 Trainee- vlan 50- 192.168.50.0/24 Gateway-192.168.50.1 Please help me. Router is on trunk port on fa0/0. Subinterface on router is Vlan10- int fa0/0.10 Vlan 20- int fa0/0.20 Vlan 30- int fa0/0.30 Vlan 40- int fa0/0.40 Vlan 50- int fa0/0.50 On router other port that is fa0/1- a wireless router is connected with that port. There is a server in manager department which is also in same vlan 40. Plz send me commands.
Could you possibly include this lab under NetSec v1.0 8.5.13 in the video description? Not a lot of people have the new NetSec version. Your videos are really helping me out with the walkthroughs.... onwards to ZPF !!!
please if you can use social media shown in 00:03 to send me more details about it
gigabit ethernet- access group not working
I need more details my friend
Thank you. Very helpful. Keep up the good work.
Thanks to you, I appreciate
ACL is not working
verify if it is applied in the correct device and interface
@@romeroc24 hlo sir, can u help me
In my project there are five department in bus topology. Like finance, testing, HR, manager, trainee. All are in different vlans with different IP address. I have all done apply vlans and all are communicating with each other. But there is requirement in my project that is manager department only should access finance department. All other departments should not access to finance department. Please send me commands which can be run in my project. I am totally fed up from internet . I have watched numerous videos but all are useless.
@@sumanchahal8068 use a standard access list to permit manager and deny any other traffic, then place that access list close to destination
@@romeroc24 can u send me commands because I applied numbers of times with different patterns but it's failed. I think I am not able to understand that how to apply these commands. I tell u network address of every department.
Finance-vlan10- 192.168.10.0/24 gateway- 192.168.10.1
Testing- clan 20- 192.168.20.0/24
Gateway- 192.168.20.1
HR- vlan30- 192.168.30.0/24
Gateway- 192.168.30.1
Manager- vlan40- 192.168.40.0/24
Gateway- 192.168.40.1
Trainee- vlan 50- 192.168.50.0/24
Gateway-192.168.50.1
Please help me. Router is on trunk port on fa0/0. Subinterface on router is
Vlan10- int fa0/0.10
Vlan 20- int fa0/0.20
Vlan 30- int fa0/0.30
Vlan 40- int fa0/0.40
Vlan 50- int fa0/0.50
On router other port that is fa0/1- a wireless router is connected with that port. There is a server in manager department which is also in same vlan 40.
Plz send me commands.
@@sumanchahal8068 ip access-list 2 permit 192.168.40.0 0.0.0.255
int f0/0.10
ip access-group 2 out
gracias !!!
como siempre salvando el día
Aprecio todo tu apoyo
Thanks sir!
thank you my friend
Good job!
Thank you for all your support my friend!
Success
Very good!!!!