As others have said - an extremely well made video - I ordered a new motor for my X4, and the replacement routine is very very similar. Do be sure that if its motor no 5471, that the belt you have fitted is no 5463. This info comes from an advisory sheet that came with the motor, and is dated 11.2011, so it may be a well known fact by now. An absolutely first class service from eSpares - it was ordered at 5.15pm one day, and with me by noon the next. Had the motor fitted and the cleaner back in action in just over three quarters of an hour, thanks to the video. Five stars!
Thanks for posting this, I found it very helpfull. The problem I had with my Sebo X4 was motor bearing failure at the drive pulley side. I could not fathom out how to get the motor apart. It turns out that the two screws holding the motor together are located under the brush boxes, you have to remove these first. The pulley is screwed onto the shaft ( right hand thread ) , remove this then get a little puller on the bearing. I got a new bearing from my local engineering shop £ 4.20, rebuilt it and off like New again.
GREAT video and VERY helpful!BUT I had a nightmare getting the spade connectors out of the old brushes! The spade has a small barb on it which allows the spade to go into the fitting easily but not to come out. It was impossible to get a grip on the spade connectors using pliers, as suggested. It was possible to gently lever the spades partly out using a small screwdriver, and then getting a pair of long nose pliers on them, but no amount of pulling and wiggling them about would release them.In the end, the solution was to force a small screwdriver into the slot in the plastic which the spade goes into, pushing it down the side of the spade and then levering the spade out.
Great help. I have a very original model bought back in 1995 and it has worked flawlessly. It has started to play up so I have taken it apart and the brushes were non-existent. The only issue is , they do not have spade terminals!! I am assuming that I will have to try to put terminals on the end of the wires.
IF the brushes supplied are the same as in the video they have a spade blade pushed into the edge of their housing to connect them. If yours differ to what is on the machine and shown in the video fill in your details at the following link and we will try and identify the correct brush for your specific model: www.espares.co.uk/contact/sales
My wonderful plasterer vacuumed up some water after cleaning up plaster power. My X4 model now has an electrical burning smell. I have thoroughly cleaned it out but it still has a smell, the longer I use it. Speculation as to the cause? New motor needed per chance?
+JulieJackson1 It is likely the plaster dust has stuck to the motor windings. When in use the air flowing through the cleaner is drawn passed the motor to cool it. The plaster coating will reduce the cooling and smell as it bakes on the windings. It may improve over time or cause the motor to pack in only time will tell.
my numatic vacuum cleaner after turning on will cause smoke what do u think might be the problem? do i need to change the carbon brushes or the whole motor?
+Flying-Machine Check to see if the carbon brushes have worn down and are causing blackening on the motor armature. If they are in good condition you may need a new motor.
hello. I just purchased a Sebo Essential G. I got a good price for it since it was the one on display at the store. Or i thought i got a good deal.... The suction on the power head is very minimal. The brush works fine. The handle suction is great. Or maybe this is what i should expect from this vacuum...? If you could give me any advice I would greatly appreciate it . I would like to get some honest feedback.
Hi Pamela, as the machine is new it is unlikely to be faulty and should not have a blockage. To check when running, if the motor noise changes much when you remove the hose or if the hose pulls strongly on to the machine it may indicate a blockage. If this is OK check the height is correctly adjusted for the surface you are cleaning.
thank you for the quick response. It is not brand new. The store I bought it from used it as a display to show to customers how it performs. I am not sure how long it was used as a display in the store. The motor noise does not change when I removed the hose. But i place my hand underneath the powerhead and it just seems like the suction is very weak. I have checked for any blockage and there was none. I am starting to think that maybe the store did sell me a faulty one. I also have a Shark and when I use that one I feel a pull from the suction being created by the power head but the Sebo does not do this at all.
Unless you are covering the whole gap the suction will just pass through the gap. The biggest effect on suction is the gap between the head and surface hence why the height is important. Also compare the power of the two machines on the rating plate as this may show the difference in performance.
Sorry we do not have a video on this but if you are referring to the pulley on the end of the motor shaft it is unlikely that you can replace this as it is not available.
My Sebo X1.1 is no longer raising when it needs to go from my laminate flooring to my carpet. It makes a loud screeching noise. It Hoover's the laminate fine though. What do you suggest please?
eSpares Thanks for your swift response. In your opinion is it worth replacing these? My Hoover is about 12 years old. Also do you sell these parts as I can't seem to find them on your website and if so how much are they and is there an instructional video for replacing them?
The correct motor for your model is here: www.espares.co.uk/product/es990442/vacuum-cleaner-servo-motor-with-gear-box We do not have instructions or a video for this repair.
In my Sebo X1 the head won't stay down. The controls just keep showing it going up and down. It never seals onto the floor. What could be the problem? I had to remove the height adjustment motor just to clean my house..
If you read the information in the manual: www.espares.co.uk/usermanual/download?userManualId=e5d331b3-447a-4b1d... You will see the automatic height is adjusted depending on the resistance of the brush roller against the floor covering. If you have deep pile carpets or the flooring is uneven the machine will keep adjusting until the brushes only lightly contact the surface so this may be normal.
Michael G A little washing up liquid is often used to allow rubber materials to slip. Without some form of lubrication if the rubber grips on to the housing it can result in the rubber mount twisting and not seating evenly. This can not only make reassembly difficult but can cause damage and distortion. The washing up liquid should be used sparingly and will soon dry up. :-)
![[LIVE] : ONE ลุมพินี 88 | คู่เอก "ป้อมเพชร vs อัสลามจอน"](http://i.ytimg.com/vi/1ZqTVVbMgbo/mqdefault.jpg)
As others have said - an extremely well made video - I ordered a new motor for my X4, and the replacement routine is very very similar. Do be sure that if its motor no 5471, that the belt you have fitted is no 5463. This info comes from an advisory sheet that came with the motor, and is dated 11.2011, so it may be a well known fact by now. An absolutely first class service from eSpares - it was ordered at 5.15pm one day, and with me by noon the next. Had the motor fitted and the cleaner back in action in just over three quarters of an hour, thanks to the video. Five stars!
Thanks bifilm. Were glad to here all went well and our service delivered.
Your vid saves people lots of money and headaches. It shows how most people can fix their own stuff. Thanks for sharing.
Thanks for your comments robviolin1, we hope we helped with your problem.
Thanks for posting this, I found it very helpfull. The problem I had with my Sebo X4 was motor bearing failure at the drive pulley side. I could not fathom out how to get the motor apart. It turns out that the two screws holding the motor together are located under the brush boxes, you have to remove these first. The pulley is screwed onto the shaft ( right hand thread ) , remove this then get a little puller on the bearing. I got a new bearing from my local engineering shop £ 4.20, rebuilt it and off like New again.
Thanks for the comments and description of the repair KirkyandKa .
Glad we helped.
Brilliant clear video, than you. 19 year old brushes were worn right down to the stubs, great service from espares
Hi Dors, Thanks for your comments and glad to here you were pleased with the service. :-)
@zakdonba We are due to do a series of videos on Miele soon, but no dates yet.
Brilliantly explained video. Worked perfectly for me. Thanks
+Patricia Brown Thanks for the comments. :-)
Fun little fact, eSpares: Sebo makes a commercial model of the X1, called the Windsor Sensor XP. Windsor is Sebo's commercial brand.
Excellent video! Very thorough demonstration.
+Matt Jones Thanks Mat. :-)
Wonderful explanation, very useful! Could you do the same on a Miele Vacuum Cleaner? All the best!
Thanks for the great info. It really helps us all.
:-)
GREAT video and VERY helpful!BUT I had a nightmare getting the spade connectors out of the old brushes! The spade has a small barb on it which allows the spade to go into the fitting easily but not to come out. It was impossible to get a grip on the spade connectors using pliers, as suggested. It was possible to gently lever the spades partly out using a small screwdriver, and then getting a pair of long nose pliers on them, but no amount of pulling and wiggling them about would release them.In the end, the solution was to force a small screwdriver into the slot in the plastic which the spade goes into, pushing it down the side of the spade and then levering the spade out.
Thanks for the comments and your description of both the problem and your solution. :-)
Great help. I have a very original model bought back in 1995 and it has worked flawlessly. It has started to play up so I have taken it apart and the brushes were non-existent. The only issue is , they do not have spade terminals!! I am assuming that I will have to try to put terminals on the end of the wires.
IF the brushes supplied are the same as in the video they have a spade blade pushed into the edge of their housing to connect them. If yours differ to what is on the machine and shown in the video fill in your details at the following link and we will try and identify the correct brush for your specific model:
www.espares.co.uk/contact/sales
Mine are from a 1995 model, 850 watt motor and the wires seem to be soldered on.
Have a look at our brushes section as you may recognise your type:
www.espares.co.uk/search?SearchTerm=sebo%20carbon
Any tips to get the cable out the board. Mine is stuck and I don't want to break it pulling it out
Is it the same process for the X4?
Whilst the job should be almost identical please see your manual for any variations. Thanks.
My wonderful plasterer vacuumed up some water after cleaning up plaster power. My X4 model now has an electrical burning smell. I have thoroughly cleaned it out but it still has a smell, the longer I use it. Speculation as to the cause? New motor needed per chance?
+JulieJackson1 It is likely the plaster dust has stuck to the motor windings. When in use the air flowing through the cleaner is drawn passed the motor to cool it. The plaster coating will reduce the cooling and smell as it bakes on the windings. It may improve over time or cause the motor to pack in only time will tell.
+eSpares Thanks for this. If it packs up, I'll know where to come for another motor. I thought I might need to buy a new vacuum. Thanks again.
Please do a Dyson DC01 motor replacement video please
my numatic vacuum cleaner after turning on will cause smoke what do u think might be the problem? do i need to change the carbon brushes or the whole motor?
+Flying-Machine Check to see if the carbon brushes have worn down and are causing blackening on the motor armature. If they are in good condition you may need a new motor.
hello. I just purchased a Sebo Essential G. I got a good price for it since it was the one on display at the store. Or i thought i got a good deal.... The suction on the power head is very minimal. The brush works fine. The handle suction is great. Or maybe this is what i should expect from this vacuum...?
If you could give me any advice I would greatly appreciate it . I would like to get some honest feedback.
Hi Pamela, as the machine is new it is unlikely to be faulty and should not have a blockage. To check when running, if the motor noise changes much when you remove the hose or if the hose pulls strongly on to the machine it may indicate a blockage. If this is OK check the height is correctly adjusted for the surface you are cleaning.
thank you for the quick response.
It is not brand new. The store I bought it from used it as a display to show to customers how it performs. I am not sure how long it was used as a display in the store.
The motor noise does not change when I removed the hose. But i place my hand underneath the powerhead and it just seems like the suction is very weak. I have checked for any blockage and there was none. I am starting to think that maybe the store did sell me a faulty one.
I also have a Shark and when I use that one I feel a pull from the suction being created by the power head but the Sebo does not do this at all.
Unless you are covering the whole gap the suction will just pass through the gap. The biggest effect on suction is the gap between the head and surface hence why the height is important. Also compare the power of the two machines on the rating plate as this may show the difference in performance.
Ok. I will try to compare and see how it goes. Thank you again for your response. I really appreciate it. ;-)
😊
great video
Hi the spring on the orange debris removing flap has snapped is it replacable
Hi Colin, what is your model number?.
Hi ensign sm2
Can I have see video how to change the pulley from the motor brushes in sebo bs?
Sorry we do not have a video on this but if you are referring to the pulley on the end of the motor shaft it is unlikely that you can replace this as it is not available.
My Sebo X1.1 is no longer raising when it needs to go from my laminate flooring to my carpet. It makes a loud screeching noise. It Hoover's the laminate fine though. What do you suggest please?
Hi Tracy, It is likely the height adjuster servo motor and gear box has failed and needs replacing.
eSpares Thanks for your swift response. In your opinion is it worth replacing these? My Hoover is about 12 years old. Also do you sell these parts as I can't seem to find them on your website and if so how much are they and is there an instructional video for replacing them?
The correct motor for your model is here: www.espares.co.uk/product/es990442/vacuum-cleaner-servo-motor-with-gear-box
We do not have instructions or a video for this repair.
Hello please mam >>you can explain the uses of shunt motor ?
Hi Manpreet, a shunt motor is a DC motor and connects both the armature and field windings in parallel.
Hello mam thanks for this video ♥
no problem :)
What a beautiful accent!
In my Sebo X1 the head won't stay down. The controls just keep showing it going up and down. It never seals onto the floor. What could be the problem? I had to remove the height adjustment motor just to clean my house..
If you read the information in the manual: www.espares.co.uk/usermanual/download?userManualId=e5d331b3-447a-4b1d...
You will see the automatic height is adjusted depending on the resistance of the brush roller against the floor covering. If you have deep pile carpets or the flooring is uneven the machine will keep adjusting until the brushes only lightly contact the surface so this may be normal.
Thanks my girlfriend's vacum now works!!!
Well done Jake, happy we helped.
Very useful - although watch those nails when replacing the motor!
Good advice to take care when fitting, we don't want anyone having an emergency sessions with a manicurist. 😊
"washing up liquid"
XD
Michael G A little washing up liquid is often used to allow rubber materials to slip. Without some form of lubrication if the rubber grips on to the housing it can result in the rubber mount twisting and not seating evenly. This can not only make reassembly difficult but can cause damage and distortion. The washing up liquid should be used sparingly and will soon dry up. :-)
eSpares I just found it funny how you call it "washing up liquid" I've always heard it called dish soap, soap, or detergent
Michael G “England and America are two countries separated by the same language.” to quote George Bernard Shaw. :-)
FYI Not all electric motors have brushes
Of course they do you idiot otherwise they wouldn't work.
@@stephensnell1379 Have you never heard of a brushless motor before?
Hello mam please upload video on you tube
Sorry we do not have a video on 'shunt motors' .