everything works. I just showed the principle of work elevators Arkel. The control panel switches the mode (revizion) because the sensor does not light up 120.130.140.
Dear my problem in the course of the power outage and switching to the source of another stream dazzling signal There is no signal in 120 and stops the elevator from work I want to tell me how to restore it to work if you want to send you a picture of the symbols of wire or something else I am ready and thank you
@@giobio11 I am already intered 00000, but without response. Moreover, the control needs puk for five digitse. Thank you sir, actuay I have two messages the first in control card which is H15. The secondth message on the screen of Adrive which is low DC Bus error no.2 .... What is the problem sir? Thank you in advance
Hello bro i have 1 Question about arkel300 same card .....its showing error H16 which is 24v (100) supply under limit..... what is solution for this error???What'sapp 00923321044431
What kind of voltage should I check? 22volt? 20? everything is very simple, there is a transformer, after the transformer there is a diode bridge. often a lot of tension goes to the call buttons on the floors unplug the power and see
у меня бывает чата такое, не закрывать замок, нет контакта дверной замке . отсутствует 120. открывает обратна, пытаясь сакрыть замок наружной или внутренний двери .
Dear elevator when he switches the power supply from one source to another stops any comment and explained to me the way to give him a signal to return to work.
где увас выдаёт ошибку? A driwe? всё может, у меня был такое прасказвание трансов, нада маркером пометить и пuстить верх вниз , не должен на крайнем этаже дать большой разнеси. маторны шкив и тросы маркером
everything works. I just showed the principle of work elevators Arkel. The control panel switches the mode (revizion) because the sensor does not light up 120.130.140.
How to set up magnet for slowing for every floor?
4th
3rd
2nd
1st
ML1 ML2 these magnets must flock on each floor
Not door zone. For slowing 142
გიორგი სალამი, როგორ შეიძლება თქვენთან დაკავშირება ?
Türkiye den gelmiş bir kumanda panosu,montajını yapmış olmak isterdim.
Me too , I have ARL 300 and need puk code , any help ?
Övüyormu Sövüyor mu ? Elinizdeki kart ve sürücü tam bir performans ürünü..
Please help Sir,
I have H15 error & the elevator don't move
Dear my problem in the course of the power outage and switching to the source of another stream dazzling signal There is no signal in 120 and stops the elevator from work I want to tell me how to restore it to work if you want to send you a picture of the symbols of wire or something else I am ready and thank you
Как подключать в ревизии
ты откуда, баку?
@@giobio11 ассалому алейкум брат я из Узбекистана
и тебя такой турецкий лифт? эта карта ARKEL 300 синкодером
Да брат я работаю мантажником .
Можно телефон номера ватсап или тлгрм
Ben de ARL 300'üm var ve puk koduna ihtiyacım var, herhangi bir yardım var mı?
the factory should be there 0000 or 000000
@@giobio11 I am already intered 00000, but without response. Moreover, the control needs puk for five digitse.
Thank you sir, actuay I have two messages the first in control card which is H15. The secondth message on the screen of Adrive which is low DC Bus error no.2
.... What is the problem sir?
Thank you in advance
Sir 24 v(100) unded limit how to solve this in arkel 300???
how can I get PUK code?
Me too , I have ARL 300 and need puk code , any help ?
@@sultans1377 I dont know if it helps as each unit might have different PUK but try 49632
Четкий шкаф
Solve a problem No signal 120 ??
Yes. No problems
Flor door 120. No closed.
130. Door elevators.
I have problem in regulor after i make on beaker FA it make short circuit how can i solve
i didn't understand, what FA?
FA is circuit breaker which is connected input to regulator then the output connacted to speed governor coil .....
@@mahdikhayre5797 send me a photo my mail. gioqartveli@mail.ru I have drawings from the elevator arkel
какой у вас плата стоит? arke300?
а я не знаю, я житель не лифтер), но могу узнать. Точно Захлифт
@@Anton-dl7me у вас нет лифтёра? нет смысла, вы не сможете исправить дефект
@@giobio11 есть лифтеры, но хз какие) Согласен что дефект справить не могу
@@Anton-dl7me я завтра сниму ролик и покажу. вы покажите лифтёру он задумается
@@giobio11 Спасибо!
I do not understand your question? (100)+24v (1000)-24v
H16 Error....Arkel 300
24v (100) supply under limit....
Hello bro i have 1 Question about arkel300 same card .....its showing error H16 which is 24v (100) supply under limit.....
what is solution for this error???What'sapp 00923321044431
@@zeechannel4229 take the tester, check how much voltage you have (100)+ (1000)- must not exceed 26 volt. MAX (24-26) volt
@@giobio11 no issue with that its 22 volts dc output from Rectifier
What kind of voltage should I check? 22volt? 20? everything is very simple, there is a transformer, after the transformer there is a diode bridge. often a lot of tension goes to the call buttons on the floors unplug the power and see
chima'yı bana gönderir misin
Please.. my problem: LM1 LM2 short circuit for each other..
у меня на этаже двери расходятся и сходятся. Через раз 10 закрываются
у меня бывает чата такое, не закрывать замок, нет контакта дверной замке . отсутствует 120. открывает обратна, пытаясь сакрыть замок наружной или внутренний двери .
Dear elevator when he switches the power supply from one source to another stops any comment and explained to me the way to give him a signal to return to work.
Where do you live?
In Palestine. Can you help me ?
Card type Arquel 300
Please.. I have problem..
No 120 Signal..
not closed exterior doors! 120. look at all the exterior door locks
@@giobio11
Thank you so much
look at the doors on the floors. no door contact
problem in Inspection box safety connection....
can you plz give me arkel 200s and 300s pdf file...
www.arkel.com.tr/arl-300-card
Downloadeble items TR/EN (can download)
Из за подшибника редуктора может быть ошибка er03
где увас выдаёт ошибку? A driwe? всё может, у меня был такое прасказвание трансов, нада маркером пометить и пuстить верх вниз , не должен на крайнем этаже дать большой разнеси. маторны шкив и тросы маркером
Lift up down thake ken
Sorry..not good sound &vedio
th-cam.com/video/-efqrreCWFY/w-d-xo.html ML1 ML2