ACTUALLY; I did notice that when doing the R&D, SO; the way round that was to make sure there was enough room for the cog to have a little lateral movement on the shaft, then I moved on to using 'O' rings so the materials holding the cog bearing in place on the shaft did not touch the outside of the bearing; Perfect!!
Follow the 6600 reels have a spring in the clutch, this may be worn and week, but it also could be a number of other things. Without seeing the reel it is very difficult to tell.
+BMW threethreefive It's obvious that the clip is nowhere near the plastic bits of the cog and that the bearing is completely free of resistance. Also, a dual bearing level wind setup solves the issue with the worm gear resistance. I have two Abus with dual bearing level winds and a ceramic pawl and they are a must for distance casting with a line guide. Absolutely amazingly smooth. Night and day difference.
@@CROWOUTDOORS the bearing is turning and touching the clip. As said above. The worm gear saps all the power anyway. Plus you'll be breaking the spool with your thumb or brake blocks so completely pointless.
If you didn't notice the C Clip is interfering with the new bearing and cog wheel ...... he didn't try spinning it once the C Clip was in place 😂
ACTUALLY; I did notice that when doing the R&D, SO; the way round that was to make sure there was enough room for the cog to have a little lateral movement on the shaft, then I moved on to using 'O' rings so the materials holding the cog bearing in place on the shaft did not touch the outside of the bearing; Perfect!!
Why not just use a ceramic bushing with ultra thin washer/spacer and thin oil?
Not a bad idea but would still cause friction.
i love this video,,,,you are truly gifted with reels , and make the best vids,,,,keep up the great work!
Hy kka
just use a bit of braid and it pops right off. no sharp knives needed.
Buenas tardes disculpe la pregunta adonde se puede comprar el kit
Mainin is Indonesia
Hi, can you make on for a UC4601c3?
I have a 5600c where this cog is held in place with a screw, will this upgrade still work and would I need to use the clip?
Need to order this and can't seem to find any that will send to Ireland or not in stock can you help
Good job>>>>>>will this work on the old "BCX6600" crap series????, i cant even find a cleaning video on it!!!
Don't know, never touched a BCX series reel
Will this work for a Abu Garcia Ambassador 5000?
have you ever replaced the cog gear post on the 6500CS
i have a 6600 c4 thumbar disengages when casting ,, any idea of what is causing this anyone?
Follow the 6600 reels have a spring in the clutch, this may be worn and week, but it also could be a number of other things. Without seeing the reel it is very difficult to tell.
thanks,,,,you build some works of art btw, im in the us so i what would it cost to pimp this one out approximately
Contact me at; jamielifetour@googlemail.com
What's the point of the upgrade? What exactly is improved?
spins faster and smoother resulting in a quieter longer casting reel.
A pointless endeavour. Worm gears on level winds sap all the power. The e clip probably still contacts the cog as well.
+BMW threethreefive It's obvious that the clip is nowhere near the plastic bits of the cog and that the bearing is completely free of resistance. Also, a dual bearing level wind setup solves the issue with the worm gear resistance. I have two Abus with dual bearing level winds and a ceramic pawl and they are a must for distance casting with a line guide. Absolutely amazingly smooth. Night and day difference.
GLK30 hi, wheee do you get the ceramic pawl??
@@CROWOUTDOORS the bearing is turning and touching the clip. As said above. The worm gear saps all the power anyway. Plus you'll be breaking the spool with your thumb or brake blocks so completely pointless.
Jamie,
The cog on your c3 should just pop right out. Being that your c3 is new, spare parts may come in handy someday.
Hello, I want two main drive cog wheels like that for my ABU 6500 C3's. How can I procure such devices?
Via my direct email at the start of the video
Can I do the same to Nacl? I really dont like the pin only, it's not smooth.
Can do it to any reel if you have the right size SS bearing.
Hi friend, where can I buy this drive cog? Thanks.
Jamie can you help me find a duel bearing idler gear for 6600c4 classic?
Direct from me at PMR
Oh and I figured out the email loll...I've sent you one
Did you order a cog wheel with bearings after all?
Im looking for a 7000
Hi Jamie
Can you supply me with the cog for a 6501c3 please, and how can I get hold of you ..?
Is this the same as the 6600 c4?
these work on a Abu 6500c. sweden
Can I get the info on getting your cog gear ?
Yr email ? I am interested in the cog wheel...
I'm sure you will work it out....
There called gears not cogs
Depends where you live in the world!
Charlie Powell If we are being grammatically correct then it’s “They’re” not “There”.
@@JT_70 😂😂😂