Your vidio editing is superb and yuor tutorials are best i was seeing videos of how to make drone with pix howk 2.4.8 flight controller but only your video satisfied me .
Your explanation is very nice and very easy to follow. I too want to build the same drone but also wish to add a 2 axis 4k action camera. Please advise which camera and how to add a camera. Thanks Sanjay Saksena ❤
My Pixhawk Main out Pin 4 is not moving the motor 4(back right - clock-wise), can you please help me on how I can use other available pins like 5,6,7,8, in pixhawk 2.4.8 and assign it channel 4. I am not able to get any document which can help on swapping the pins. It'll be a great help. Also my motor 4 is working when connected to main out pin 1,2,3 of pixhawk. I am using FSi6 TX with FSiA6B RX.
Can you please share the reason why my Pin 4 main out is not able to run the motor 4 while it is running through other Main Out Pin and how I can configure pin 5 for channel 4
@@sqlacademy you have to choose quad x config in second tab ,have you installed the proper firmware ? make sure those two are correct ,once you teardown flight controller and check whether soldering of pin is proper to the board .using 5 th pin instead of 4th pin is not possible acc to my knowlege and my research.
@@gagantech I have assigned the Pin 5 of Main Out to Motor 4 in Pixhawk by making the changes in the Parameters, here is the link which can help you doing so - ardupilot.org/copter/docs/parameters.html#mot-pwm-type and it worked, it could be problem with the Pin 4 , so I have decided not to use it. It is flying now. Thanks for all your support.
I'm using pixhawk 6c and pm07 power module and airframe F450.I have broken pins M4 and M1 in PM07 representing motor 4 and motor 1, can I use two pins M6,7,8 instead and calibrate it for motor 4 and motor 1?
since M1-M8 are used for pwn outputs , yes u can connect anywhere , make sure u adjust the settings accordingly in the parameter section of mission planner.
Hello! Thank you so much for the video. It's very clear and you make it seems easy! I want to ask, what is the maximum weight this drone can carry? I want to use the same drone to carry a box. I want to know thw maximum. Thanks in advance!
Thrust of each motor is 700 g (in my case ) total thrust of motors is 700 *4 =2800 gram. The weight of my quad is 900 gram so , 2800-900 = 1900 gram. 1900 gram is usable for your application. The more gap you leave more flight time you will get. Try to reduce weight of your box for efficiency .
@@shaikha.malzaabi7286 if you use golden motor of 1000 kv there will be lot of vibration, if that's ok then you use it. Yes you will get slightly more thrust than 920kv motor ,around 780-820gram.But if you use camera(golden motor)you will have a lot of jello.
Hello sir, My name is Shiba. Actually I have built a drone for my college project. Using radiolink cross flight also using GPS. But the drone is not properly flying. I need your help please.
i am saying according to ur video.... in video when u do turning left and right drone while calibration...... so that those who are doing drone watching ur video..... they will miss the point..... since accelerometer is one of the most important play roll in drone..... don't mind for saying.....
Thanku for bringing it to notice , since it’s my first video there are a lot of mistakes , I don’t mind it cause there’s is lot of room for improvement 😅. The mistake will be corrected soon..
One question: when pixhawk (flight controller) is connected to FS-ia6b (receiver), the led on receiver does not work. The receiver works correctly when connected to ESC and battery. Do you think I am doing something wrong? Thank you.
@@gagantech sorry just saw the message.. I’ll ping you on Instagram.. btw It seems I have connected everything as shown in your video and others as well.. but it does not work..
Hi bro I'm doing project on drone at first i have used the Arducopter the issue i was faced is that it was not stable it was lifting up vertically but while lifting vertically it was moving right and left without any movement in direction channels and now I'm using Pixhawk flight controller and the Same issue i am facing with Pixhawk also. So please can you help me in stabilization of drone using Pixhawk
Hi, its nice video. i am facing some issue. While installing firmware its showing already on your board but really not. kindly let me share the solution for updating latest firmware.
Bro I built a drone a year ago... Wo aajtak ekbaar bhi nehi ura Maine sabkuch check kara, pura software firse dala, bohot yt video dekha, mere hardware me koi problem nahi nazar aya, wo gps recognise hota hai, esc calibration bhota hai, propeller ghumta bhi hai but thori der baad ruk jata hai urta nehi... Mai jab bhi wo drone ko dekhta hoon bahot depressed lagta hai... If you can give me a suggestion My drone specs Pixhawk 2.4.8 Gps Fs i6 transmitter and receiver A Chinese frame copied from f450 4 x 1400 kv golden bldc motor 4 x 30a esc 3300 mah battery 4 x 1045 propeller (2 cw 2 ccw) 4 landing gears Please answer...🥺🥺🥺
Price mostly depends on flight controller your using. if you use pixhawk it will cost u around 20k or else if u use kk 2.1.5 it will cost you around 12k . If u have any other doubts feel free to ask. Also please don't forget to subscribe my channel. And give me a suggestion of what should be my next video?
To locate the position of the drone and for returning to its initial position, consider subscribing to my channel , if u have any doubt regarding drone building mail me to gagankushal3@gmail.com
Make sure motors are spinning in correct directions and props are put properly and adjust all the trims to centre hope ur issue will be solved in case u have further issue help me with a small clip showing the problem and send it to my mail Or Instagram
Bro I have did drone after seeing ur video ... It really help me a lot in getting good equipment But I have facing a small problem , i was not flying stable can u help me
This is my first video on youtube so if there are any mistake please neglect it and support me to give more useful content by subscribing the channel ,please help me reach 500 subscribers ,as the build video of racing drone and fpv car will posted as soon as my channel reaches 500 subscribers.
Brother I tried it in althold and poshold modes but the drone is still unstable, i need your help urgently. I have requested you in Instagram, accept soon
Your vidio editing is superb and yuor tutorials are best i was seeing videos of how to make drone with pix howk 2.4.8 flight controller but only your video satisfied me .
Thanks for the compliment , since it's my first video I have lot of things to get it right .
If u have any doubt, feel free to contact me on Instagram I will be happy to help you.
U saved me for my Final year project bro
Thanqu please subscribe my channel
Thanks bro for disassemble and reassemble the drone only for the video
If u have any doubts regarding drone building please contact me to my gmail in the description and please subscribe to my channel
Your explanation is very nice and very easy to follow. I too want to build the same drone but also wish to add a 2 axis 4k action camera.
Please advise which camera and how to add a camera. Thanks Sanjay Saksena ❤
Contact me on Instagram @ga.gandeep6831
I will answer all your queries there
Bro can I know how much higher it will fly
120 mtrs is limited according to country' s rules and regulations. You can fly as far as line of sight,for safety purposes.
If you found it helpful.Please subscribe my channel bro
@@gagantech99❤❤
@@gagantech9❤9❤
9
Super explaiation bro .....
Thq
Congratulation gagan 👍
Congratulations Gagan, good luck.
Op bro
Op
thanks
Nice stable drone I want to try it
thanks
Does it require power distribution board?
No it does not,The f450 frame has built in pdb
Congrats gagan...
My Pixhawk Main out Pin 4 is not moving the motor 4(back right - clock-wise), can you please help me on how I can use other available pins like 5,6,7,8, in pixhawk 2.4.8 and assign it channel 4. I am not able to get any document which can help on swapping the pins. It'll be a great help. Also my motor 4 is working when connected to main out pin 1,2,3 of pixhawk. I am using FSi6 TX with FSiA6B RX.
Can you please share the reason why my Pin 4 main out is not able to run the motor 4 while it is running through other Main Out Pin and how I can configure pin 5 for channel 4
Have you ensured all config settings are correct in mission planner
@@gagantech I have followed your guidelines. Can you share the steps of mission planner in detail
@@sqlacademy you have to choose quad x config in second tab ,have you installed the proper firmware ? make sure those two are correct ,once you teardown flight controller and check whether soldering of pin is proper to the board .using 5 th pin instead of 4th pin is not possible acc to my knowlege and my research.
@@gagantech I have assigned the Pin 5 of Main Out to Motor 4 in Pixhawk by making the changes in the Parameters, here is the link which can help you doing so - ardupilot.org/copter/docs/parameters.html#mot-pwm-type and it worked, it could be problem with the Pin 4 , so I have decided not to use it. It is flying now. Thanks for all your support.
I'm using pixhawk 6c and pm07 power module and airframe F450.I have broken pins M4 and M1 in PM07 representing motor 4 and motor 1, can I use two pins M6,7,8 instead and calibrate it for motor 4 and motor 1?
since M1-M8 are used for pwn outputs , yes u can connect anywhere , make sure u adjust the settings accordingly in the parameter section of mission planner.
Now 15 August is coming , so i have advice to add a tiranga and host it in air . Please make it and post video regarding to this ❤❤❤🎉🎉🎉🎉🎉broo
Thanku so much 😍 i will surely do it
Nice one brother
Thank you
Gagan, it's amazing👌👌 Appreciate your interest🤍 Keep going broo..
Thq bro
When will you upload next video please do a give away giving 4 ready to sky motors
Hello! Thank you so much for the video. It's very clear and you make it seems easy! I want to ask, what is the maximum weight this drone can carry? I want to use the same drone to carry a box. I want to know thw maximum. Thanks in advance!
Thrust of each motor is 700 g (in my case ) total thrust of motors is 700 *4 =2800 gram. The weight of my quad is 900 gram so , 2800-900 = 1900 gram. 1900 gram is usable for your application. The more gap you leave more flight time you will get. Try to reduce weight of your box for efficiency .
@@gagantech Thank you so much! that was very useful
@@gagantech but how can I know the thrust of the motor? I think you used 920Kv motor. If I use 1000Kv motors will it have higher thrust?
@@shaikha.malzaabi7286 if you use golden motor of 1000 kv there will be lot of vibration, if that's ok then you use it. Yes you will get slightly more thrust than 920kv motor ,around 780-820gram.But if you use camera(golden motor)you will have a lot of jello.
To know the thrust of motor you have to do bench test i.e test motor and prop thrust on weighing machine.
Have you ever made a drawing with LiDAR or metallic seeking hardware?
Nope not yet
I want to know more about it
Bro I used 3cell 8000mah battery
During take of my power module start burning. What can I do please help me bro
I will help u soon
pixhawk is not communicating with fs ia6b. My connections are fine. (apm 2.8 also works) pixhawk didn't work either. what could be the problem.
fs i6 - fs ia6b - pixhawk 2.4.8
I will definitely help you out with the issue, which medium did you use like sbus or ibus or pwm?
@@gagantech I have used ppm and ibos and no response.
I updated the remote, tried different versions, the problem was not solved.
This is my email - gagankushal3@gmail.com please mail me there also send me a short video of the issue in the mail
Good job dear bro.. Keep it up♥️🔥
Thq
Nice work
What will be the flying time in single charge
10-12 min
@@gagantech thanks bro✨
Please sub my channel
@@gagantech bro I have also same drone but I am facing problem
How to connect esc to motor please bro help me how I can contact you please bro
Hello sir, My name is Shiba. Actually I have built a drone for my college project. Using radiolink cross flight also using GPS. But the drone is not properly flying. I need your help please.
Contact me Instagram @ga.gandeep6831
Or mail me at gagankushal3@gmail.com
How much flight time can we get from this setup
7-9 min max real world, I m building a bigger drone with flight time 20 mins + stay tuned and subscribe my channel
look like accelerometer caliberation is not correct?
Could you please elaborate, seems like no problem the drone is working properly
i am saying according to ur video....
in video when u do turning left and right drone while calibration......
so that those who are doing drone watching ur video.....
they will miss the point.....
since accelerometer is one of the most important play roll in drone.....
don't mind for saying.....
Thanku for bringing it to notice , since it’s my first video there are a lot of mistakes , I don’t mind it cause there’s is lot of room for improvement 😅. The mistake will be corrected soon..
One question: when pixhawk (flight controller) is connected to FS-ia6b (receiver), the led on receiver does not work. The receiver works correctly when connected to ESC and battery. Do you think I am doing something wrong? Thank you.
Mssg me over Instagram I will help you @ga.gandeep6831
have you connected it the correct way? i.e -ve pin in the top of pixhawk ?
@@gagantech sorry just saw the message.. I’ll ping you on Instagram.. btw It seems I have connected everything as shown in your video and others as well.. but it does not work..
Tried messaging you on Instagram but it says you can’t receive new message as the account settings does not allow..
I followed u back
Hi bro I'm doing project on drone at first i have used the Arducopter the issue i was faced is that it was not stable it was lifting up vertically but while lifting vertically it was moving right and left without any movement in direction channels and now I'm using Pixhawk flight controller and the Same issue i am facing with Pixhawk also. So please can you help me in stabilization of drone using Pixhawk
The problem will be with the esc
Try replacing it and check, if it didn’t work message me on Instagram at ga.gandeep6831
Ok bro
Hi,
its nice video.
i am facing some issue. While installing firmware its showing already on your board but really not.
kindly let me share the solution for updating latest firmware.
mssg me on instagram @ga.gandeep6831 i will help u there
Bro i want to make one so can u help me to build one🙏
If you have any queries please feel free to ask.
@@gagantech l want to ask personal bro
My mail : gagankushal3@gmail.com
You can ask your queries in my gmail
@@gagantech i already sent you a massage
nice but while implementing i had some issue regarding receiver, i have mailed it elaborately. kindly check it and reply asap
I am trying it now but facing some trouble. can you help me?
Yeah sure Dm on Instagram find id in description
Bro I built a drone a year ago...
Wo aajtak ekbaar bhi nehi ura
Maine sabkuch check kara, pura software firse dala, bohot yt video dekha, mere hardware me koi problem nahi nazar aya, wo gps recognise hota hai, esc calibration bhota hai, propeller ghumta bhi hai but thori der baad ruk jata hai urta nehi...
Mai jab bhi wo drone ko dekhta hoon bahot depressed lagta hai...
If you can give me a suggestion
My drone specs
Pixhawk 2.4.8
Gps
Fs i6 transmitter and receiver
A Chinese frame copied from f450
4 x 1400 kv golden bldc motor
4 x 30a esc
3300 mah battery
4 x 1045 propeller (2 cw 2 ccw)
4 landing gears
Please answer...🥺🥺🥺
Yes I will surely help u out mssg me on Instagram in the description I have helped many members don't worry
Bro can you please tell how to connect esc and motor please
refer my video above if still query ,please follow my instagram account : ga.gandeep6831 and mssg me there
Hello, Whats motor you use?
Readytosky 920kv brushless motor
Please subscribe to my channel
Thank You!
What is estimated price material price of drone pls tell
Price mostly depends on flight controller your using. if you use pixhawk it will cost u around 20k or else if u use kk 2.1.5 it will cost you around 12k . If u have any other doubts feel free to ask. Also please don't forget to subscribe my channel. And give me a suggestion of what should be my next video?
@@gagantech bro mini drones means i am just a student for me i just want for project
@@renukanagul1389 ok for mini drone it will cost you below 6k approx
Please subscribe to my channel
@@gagantech ok bro thanks can you pls tell me only price of transmitter and flying controller
Nice drone
Hi bro can you please help me out for my dron program
Yeah sure contact me on insta @ga.gandeep6831
What is the use of GPS? Why
To locate the position of the drone and for returning to its initial position, consider subscribing to my channel , if u have any doubt regarding drone building mail me to gagankushal3@gmail.com
Bro my drone fly only right side. Transmitter throttle up drone fly right side
Make sure motors are spinning in correct directions and props are put properly and adjust all the trims to centre hope ur issue will be solved in case u have further issue help me with a small clip showing the problem and send it to my mail Or Instagram
Please give away
ill giveaway when 20ksubscribers
What is the Total cost about that please tell me ?
Depends on ur drone, mine costed around 20k inr
Bro I have did drone after seeing ur video ... It really help me a lot in getting good equipment
But I have facing a small problem , i was not flying stable can u help me
Yes, please mail me or contact me on Instagram refer description box for ids
@@gagantech thanks bro
Have u messaged me? Yet
@@gagantech yes
Dint get any
👌
What is the fly time sir
8-12 mins depending on the config
Can I use Fs-r6b?
Yeah u can use fsr6b, it has 6 channel and it is compatible
Please consider subscribing to the channel.
you know how to connect? fsr6b receiver?
i try to connect my fsr6b but the transmitter not functioning
Please mail me Or mssg me on Instagram will help u out there
👏🏻👏🏻👏🏻
Excellent video tutorial, thanks for the tips!
Hlo bhai
Help me
Yeah sure ,ask the question please subscribe
@@gagantech kr diya ho
Batao do
PLEASE VISIT THIS SHORTS :th-cam.com/users/shorts7Trp8SJzHrg?feature=share
This is my first video on youtube so if there are any mistake please neglect it and support me to give more useful content by subscribing the channel ,please help me reach 500 subscribers ,as the build video of racing drone and fpv car will posted as soon as my channel reaches 500 subscribers.
How to contact you
Mail me using the email in description
need some assistance regarding a pixhawk drone. can i contact you over email/phone ?
Email- gagankushal3@gmail.com
Please subscribe the channel for more of such content
Brother I tried it in althold and poshold modes but the drone is still unstable, i need your help urgently. I have requested you in Instagram, accept soon
Sure