Eugenio M use the manual under the machine it’s stuck to side in plastic and you can put the washer in service mode which tests certain parts and also you can put the washer in fault mode and it will display fault codes
My ge washer was not draining or spinning. Also I noticed the lid lock switch was not coming on. About 5 different error codes were showing. We check the pump, around the tub to make sure there was nothing clogged are blocking the washer from spinning. So we started back with what I had noticed at first. The lid lock switch light was not cycling on. So we switched out the lid lock which is located when you lift the the lid looked down uts on the right side. There are you tube video to show you how to get to it. We switched it. Washer stronger than ever. No more error codes. Hope this helps someone. Check lid lock switch if you get washer is throwing several error codes. Also videos on YT to show how to check codes.
Yeah we were lied to big time. We paid almost 1000 for it and they said it was bc it was the best on the market. We used it for almost a year when it started giving us issues. I’m so pissed
I have the same model he's showing here, the machine would not do anything except make clicking sounds and the tub was full with water, would not spin or rinse or anything. i unplugged the machine for quite a while then plugged back in and within 30 seconds opened and closed the top 6 times and then rotated the dial to rinse and spin and pressed start and it began to operate normally!
Please replace lid lock because Main board go to protection in relay k501 because it do not received logic state 2.5 volt at 5 volt in Microprocessor... but if you change the lid lock and it not was fixed you need to check various electronic components around it circuit..[DIODE AND resistors]. if you need more information please let me know I WILL SEND A LINK ABOUT .... but if you run a test program and disconnect the connection [ lid lock from board] you will see that it change state light flashings because the microprocessor do not received logic state or information about internal contact Swisher LID LOCK IF IT IS OPEN OR CLOSED AND IS FOR THAT THE microcontroller GO TO DOWN AT SAFE MODE OR protection MODE AND YOU SEE ALL LED IS OFF AND NOT nothing [THE WASHER machine NOT WORK].....I AM SORRY MY ENGLISH NOT GOOD
I have this exact washer machine and model. I HATE IT! No matter how evenly you distribute the articles of clothing to ensure proper weight distribution it goes off kilter 8 out of 10 loads. I only do small or medium loads, you can't do heavy loads or it will not spin or drain properly. I've had this machine for 3 years (purchased in November of 2016) and it's just one huge disappointment. I can't even leave a load unattended because it constantly goes off kilter. These High efficiency washers are absolute crap, this is my 3rd GE HE washer because the prior 2 broke within 1-2 years. I had a non-HE GE washer (purchased in 2013) and it was a dream! you can put comforters in it and no issues. I regret not taking it with me when I had moved.
Hi Jessica, I personally haven't, but if you type the below title in the search bar a video on how to do it will populate. "How to Bypass Magnetic Lid Switch on GE Washer "
I have this same washer., purchased in early 2016. I’ve had problems from week 1. First, it runs loud. Secondly, it’s a problem sometimes going to the next cycle. No it stopped completely.
I have this same washer and had the same problem. Replaced the water inlet assembly first.. Did not resolve the issue, then replaced the lid switch. Issue now resolved. Long story but I am not sure which of the two actually was the issue, but I hope this helps somebody.
I have it too and this is why I'm watching videos like this. If I can't get it fixed before Monday then I have to figure out how to meet a repairman in an 8 to 12 window and I won't be home until after 10. I missed the AT and T guy the same way over the summer. I'm a school bus driver and we are probably going to be short of drivers and I need the money. I've already had a repairman out here once before to run the computer driven, overly smart model, through it's motions to get it going again. I'm going to flip mine back over and see if the motor has dirt or debri in it since I've been putting very dirty jeans in it
So does mine it is driving me crazy it won't do a load of laundry at all then I have to turn it to drain and spin for the washer machine to lock the lid and finish
Why are you not talking and explaining what you are doing and you’re doing it so fast how are we to keep up? now, I have to also reboot your video another problem added to my problem. Thank you for time wasted
I hate this washer with all my heart. This lid lock is the worst. Go back to the simple stuff. I need easy to understand and use over technology any day
The worst washer ever made by GE, it guarantees you a lot stress every time you use it.. I never recommend it to anyone.
Eugenio M use the manual under the machine it’s stuck to side in plastic and you can put the washer in service mode which tests certain parts and also you can put the washer in fault mode and it will display fault codes
U never lied
My ge washer was not draining or spinning. Also I noticed the lid lock switch was not coming on. About 5 different error codes were showing. We check the pump, around the tub to make sure there was nothing clogged are blocking the washer from spinning. So we started back with what I had noticed at first. The lid lock switch light was not cycling on. So we switched out the lid lock which is located when you lift the the lid looked down uts on the right side. There are you tube video to show you how to get to it. We switched it. Washer stronger than ever. No more error codes. Hope this helps someone. Check lid lock switch if you get washer is throwing several error codes. Also videos on YT to show how to check codes.
I agree mine just did this today ☹️🤦🏽♀️
Yeah we were lied to big time. We paid almost 1000 for it and they said it was bc it was the best on the market. We used it for almost a year when it started giving us issues. I’m so pissed
I'm up at 3:12 a.m. trying to wash (3 not working now) and this video is so me right now. I keep watching it too lol
Exactly my problem. How do you fix this?
update: the blade of my cousins pocket knife slid into some gear.
I have the same model he's showing here, the machine would not do anything except make clicking sounds and the tub was full with water, would not spin or rinse or anything. i unplugged the machine for quite a while then plugged back in and within 30 seconds opened and closed the top 6 times and then rotated the dial to rinse and spin and pressed start and it began to operate normally!
Did you ever find out what was wrong?
Please replace lid lock because Main board go to protection in relay k501 because it do not received logic state 2.5 volt at 5 volt in Microprocessor... but if you change the lid lock and it not was fixed you need to check various electronic components around it circuit..[DIODE AND resistors]. if you need more information please let me know I WILL SEND A LINK ABOUT .... but if you run a test program and disconnect the connection [ lid lock from board] you will see that it change state light flashings because the microprocessor do not received logic state or information about internal contact Swisher LID LOCK IF IT IS OPEN OR CLOSED AND IS FOR THAT THE microcontroller GO TO DOWN AT SAFE MODE OR protection MODE AND YOU SEE ALL LED IS OFF AND NOT nothing [THE WASHER machine NOT WORK].....I AM SORRY MY ENGLISH NOT GOOD
Did you ever fix the problem?
Is something wrong with the motor and engine
I just got same washer but on a heavy cycle it only fills not even half way with water
I have this exact washer machine and model. I HATE IT! No matter how evenly you distribute the articles of clothing to ensure proper weight distribution it goes off kilter 8 out of 10 loads. I only do small or medium loads, you can't do heavy loads or it will not spin or drain properly. I've had this machine for 3 years (purchased in November of 2016) and it's just one huge disappointment. I can't even leave a load unattended because it constantly goes off kilter. These High efficiency washers are absolute crap, this is my 3rd GE HE washer because the prior 2 broke within 1-2 years. I had a non-HE GE washer (purchased in 2013) and it was a dream! you can put comforters in it and no issues. I regret not taking it with me when I had moved.
I have this problem and I have already replaced the lid switch so I’m back to square one
Having the same problem with mine. Bypassed the lid lock but didn’t work. Has anyone solved this problem?
3 wire lid switch ...
elkslaxer18 look under the washer there is a manual and you can put the washer in test mode or get binary fault codes to help you
I heard if you place a magnetic strip on the right hand side (where the lid would rest when closed) it bypasses the sensor.
@@jackieland77 did you try it?
Hi Jessica, I personally haven't, but if you type the below title in the search bar a video on how to do it will populate. "How to Bypass Magnetic Lid Switch on GE Washer "
Are all the Cycles not working
Has any of you contacted GE and complained to see if there is something they will do
I have this same washer., purchased in early 2016. I’ve had problems from week 1. First, it runs loud. Secondly, it’s a problem sometimes going to the next cycle. No it stopped completely.
Dont forget to so the Hokiy Pokieee and twirrllll alll about😅😅😅😅
When you press start, the lights will go off for 7 seconds and you will hear the sound from the door lid lock end start again.
What’s the name of your new machine cuz Ima throw this one out too lol 😂
What did u do to fix?
Sell it👌👌
I’m having the same problem. Took out all clothes and now full of water and detergent
Did you fix it
I have this same washer and had the same problem. Replaced the water inlet assembly first.. Did not resolve the issue, then replaced the lid switch. Issue now resolved. Long story but I am not sure which of the two actually was the issue, but I hope this helps somebody.
Thanks have same problem now as I speak
@@hellnaw16Was it your lid switch? I think that's the issue on mine but I don't feel like taking apart the entire washer just for a switch.
@@BRUCEYBOY had to reset it start back working
I have ge washing machine top loader but immediately you on the power then it started draining water out
Any question for my ge washing machine
I’m having problems with this also it my dose not drain or spin
Same here, I unplugged it to rest and plugged it back in and it sounds like the drain cycle is on but no lights on and it's not doing snything.
Is it freaking broken
Mine is doing same thing change lid lock switch didn't fix the problem
Did you ever figure it out?
I have this Machine and it SUCKS...... I ABSOLUTELY HATE IT
I have it too and this is why I'm watching videos like this. If I can't get it fixed before Monday then I have to figure out how to meet a repairman in an 8 to 12 window and I won't be home until after 10. I missed the AT and T guy the same way over the summer. I'm a school bus driver and we are probably going to be short of drivers and I need the money. I've already had a repairman out here once before to run the computer driven, overly smart model, through it's motions to get it going again. I'm going to flip mine back over and see if the motor has dirt or debri in it since I've been putting very dirty jeans in it
I have the same lousy machine. Very disappointing. Lasted less than two years.
whats the fix?
I got mine 2 years ago the warranty just expired Im deeply hurt as my washer is doing the same thing
Im a tech speed queen is the best i only worked on 2 in 13 years of doing this
Can’t understand this video
I have the same EXACT problem!!!
you guys are lucky I have it 2 weeks it fucked up already
I have the same machine and it is causing me so much trouble it just stops in the middle of the cycle
Money Maker for Service people Shit can it trust me…big POS💩💩💩💩💩💩🤡🤡
So does mine it is driving me crazy it won't do a load of laundry at all then I have to turn it to drain and spin for the washer machine to lock the lid and finish
I’m at the laundry mat every other month because of this awful purchase. The fault codes are a joke!
I have the same issue as well
jude paul look under the washer and find the manual and you will be able to use the binary fault codes to find out what’s wrong it
I had to do a motor reset on mine
Did it fix the problem?
Any good answer how to get it run please
Not really sell it u will be glad u did Mr Appliance Guy for 30 yrs recommendations…sell it
Why are you not talking and explaining what you are doing and you’re doing it so fast how are we to keep up? now, I have to also reboot your video another problem added to my problem. Thank you for time wasted
This is definitely nt user friendly. They hve literally over complicate doin ur laundry.
I hate this washer with all my heart.
This lid lock is the worst. Go back to the simple stuff. I need easy to understand and use over technology any day
Worked like a charm!
HoW CAN I GETY MONEY BACK IT TOTALLY TRASH 😤
That help like throw it out thanku
remplace lid lock
Washer sucks horrible
Bad video!
I think the new GE top loading are a real fucking piece of shit. Chinese built!!! The GE Filter Flo Washing Machines are way better!!!
😠😠👎👎👎