Hi Bro, thanks for that amazing project! Can you please show us which controller you bought? And maybe a link for the custom firmware? Or maybe even a video of how to flash it?
Hello.. I am an old man living in rural America. I was impressed by your video. It was the best video of its kind I've ever seen. I want to use this video to make an RC truck for my grandson. If possible, you can share wiring schema for remote controller, from 08:21 to 08:38.scene
It appears turning is done by spinning motors in opposite direction. How is that wired so the motors will spin in opposite direction? Is there a reverse wire on the hub motor speed controllers?
Hi ! What is the minimum travel speed? I would be interested for a personal project, I would need a speed between 2-5 cm/sec, for a platform weight of approximately 60-70 kg. I would like to know if such a low speed can be obtained while keeping the torque, before I start inventing... 🙂 What you have achieved is excellent, dear! Thank you very much!
10 หลายเดือนก่อน
What is the total width and length of the bearing capacity of the plate, thanks...
do diagram how you connected those wires together between the 2 motherboards? im having a hard time seeing the video. i see some wires look cut and the next clip everything is put together. it seem like o alot of use would lie to see that so we can do it. you didnt share that with us on the video that would be very very very very ...helpful
@@MakerMan like you connect the pa2,pa3 and ground to a splitter then the end cable is connected to the receiver. I thought the red wire 15v you don’t connect? Plus i recently seen someone in GitHub connect behind the board with a capacitor I’m not sure what to call it. It seems like everybody’s has a way of connecting it differently. Is there anyway you can have a video of how you did it, so it makes more sense to me and maybe others that might be watching like have a close-up of the wiring, how you connected it to your receiver
@@Auras-4WD I guess it depends on how you wired your connection. I seen a few videos they seem to connect them differently. From what I was told. I would get the 2nd board and only connect the Rx with directly to the 1st board Rx if this makes sense. I have ordered a 2nd board so I’m just waiting for it to come in so I can test it out
@@bluecavemen i cant find any video with 2 boards that shows exsctly how to connect. Splitted signal wires not working with gnd, 5v powered from one board.
Hi, I tried to make 4wd hoverboard bbcar also. But i could control it only with ADC (with two pots) but i could not control it from rc transmitter / receiver. Could you please share your firmware for Rc control? Did you use one hoverboard's motherboard for front wheels? (or one for right front wheel and left back wheel?) thanks for yourhel by now.
Nice build and building. Just the way of bending the sheet for holding the battery pack i don't understand. How it is possible to get a nice angle without some massive plate on top of it. I would placed the sheet between table and the plate and then go down wards (even need a hammer to get as small curb) maybe i miss something.?
Hi Buddy Very good project I like it, I want to make like this 2WD , May I know which custom firmware you used, Can you help me for remote connections? Thanks for all this. Paul
I wanted to do exactly this for years. Not only is your design almost exactly as I had imagined, I think the dimensions are close too... I wanted to add a RasPi, Lidar scanner and do autonomous driving with SLAM so I could use it as a goods trolley that would automatically go where you tell it without remote control. Anyway, You did an amazing job! I love this. Really well put together. How badly are the wheels getting stripped of rubber due to that skid steering though?
Hey brother great project. I'm hoping to finish my build of similar one soon. Did you share anywhere a repository for firmware? Very nice work this is!!! Keep well
Доброго времени суток. Я сейчас делаю что то подобное. Но проблема в программировании. Если Вы покажете более подробно как это сделать. Буду весьма благодарен....
Hi Bro, thanks for that amazing project! Can you please show us which controller you bought? And maybe a link for the custom firmware? Or maybe even a video of how to flash it?
Exceptional work, and so much attention to detail and quality too! One of these would be be SO useful on the farm! I can imagine dozens of uses!
True
And thanks
Hello.. I am an old man living in rural America. I was impressed by your video. It was the best video of its kind I've ever seen. I want to use this video to make an RC truck for my grandson. If possible, you can share wiring schema for remote controller, from 08:21 to 08:38.scene
It appears turning is done by spinning motors in opposite direction. How is that wired so the motors will spin in opposite direction? Is there a reverse wire on the hub motor speed controllers?
Hi ! What is the minimum travel speed? I would be interested for a personal project, I would need a speed between 2-5 cm/sec, for a platform weight of approximately 60-70 kg. I would like to know if such a low speed can be obtained while keeping the torque, before I start inventing... 🙂 What you have achieved is excellent, dear! Thank you very much!
What is the total width and length of the bearing capacity of the plate, thanks...
do diagram how you connected those wires together between the 2 motherboards? im having a hard time seeing the video. i see some wires look cut and the next clip everything is put together. it seem like o alot of use would lie to see that so we can do it. you didnt share that with us on the video that would be very very very very ...helpful
It's parallel connection with the 2 boards. Like gnd, 5v, ch1 and ch2.
@@MakerMan like you connect the pa2,pa3 and ground to a splitter then the end cable is connected to the receiver. I thought the red wire 15v you don’t connect? Plus i recently seen someone in GitHub connect behind the board with a capacitor I’m not sure what to call it. It seems like everybody’s has a way of connecting it differently. Is there anyway you can have a video of how you did it, so it makes more sense to me and maybe others that might be watching like have a close-up of the wiring, how you connected it to your receiver
@bluecavemen have figure out how 2 boards connected? Describe plz or schema. How one receiver is wired with both
@@Auras-4WD I guess it depends on how you wired your connection. I seen a few videos they seem to connect them differently. From what I was told. I would get the 2nd board and only connect the Rx with directly to the 1st board Rx if this makes sense. I have ordered a 2nd board so I’m just waiting for it to come in so I can test it out
@@bluecavemen i cant find any video with 2 boards that shows exsctly how to connect. Splitted signal wires not working with gnd, 5v powered from one board.
Hi, I tried to make 4wd hoverboard bbcar also. But i could control it only with ADC (with two pots) but i could not control it from rc transmitter / receiver. Could you please share your firmware for Rc control?
Did you use one hoverboard's motherboard for front wheels? (or one for right front wheel and left back wheel?) thanks for yourhel by now.
What controller did you use and how did you get it to communicate with the hoverboard chips?
I used pwm rc 2.4ghz. by flashing custom firmware to hoverboards mainboard.
Можете його показати ?
@@MakerManyour own firmware or is there a git?
Nevermind, found it:)
@@DJOetkenPlease share.
Hey i want to ask you you programed motherboards separately to one rc controller or together? 🙂
Can I buy this or can you make me just the electronic section?
email me please
Nice build and building.
Just the way of bending the sheet for holding the battery pack i don't understand.
How it is possible to get a nice angle without some massive plate on top of it. I would placed the sheet between table and the plate and then go down wards (even need a hammer to get as small curb) maybe i miss something.?
I have pre grinded the grooves with angle grinder, off camera.
That's why you don't need to hummer it.
@@MakerMan Ok.. that i did miss, thanks for clarifying.
Interesting video. Please show me how to connect 2 hoverboard boards to RC remote controller. Thank you
U just need to connect it parallelly
I really need a platform with traction! Can you help me ?
Just put rubber on top (velcro or glue, just to be sure).
hello markerMan, i‘m interested in such a 4wd moving plattform. do you sell them?
Email me please.
Awesome job. Ready for Battle Bots!
Thanks, that's an idea :)
hi
can you share wiring schema for remote controller, 08:21. scene
Email me
Fantastic project
Thanks buddy
Hi Buddy
Very good project I like it, I want to make like this 2WD , May I know which custom firmware you used, Can you help me for remote connections? Thanks for all this.
Paul
Hello, how can you? I need help with firmware, thank you 🙏
is there a parts list or project breakdown of this in text form?
Not really, it was a go the flow approach of the build.
That is awesome, now make a 6x6 crawler like the mars rover !
I appreciated this item and wondered if you would be willing to make and sell 2 of them (waterproofed for outdoor purposes) to me?
Email me
Hi, I can't make a firmware modification that works well for the same project as you, could you share your 4wd firmware?
How do I contact makerman?
I wanted to do exactly this for years. Not only is your design almost exactly as I had imagined, I think the dimensions are close too... I wanted to add a RasPi, Lidar scanner and do autonomous driving with SLAM so I could use it as a goods trolley that would automatically go where you tell it without remote control. Anyway, You did an amazing job! I love this. Really well put together. How badly are the wheels getting stripped of rubber due to that skid steering though?
Wheels are fine for now
Automation is the next upgrade for this. Still learning how to ;)
Hey brother great project. I'm hoping to finish my build of similar one soon. Did you share anywhere a repository for firmware? Very nice work this is!!! Keep well
I like this product
Hats off 👌🏻
Thanks
buying this project
hey, can I buy such a plattform. that would be amazing
Email me please
Impressive project, nicely done!
Thanks.
what radio did you use for this rig to control the bldc motors?
It would be great if it can be adapted to a lawnmower
Yes
Доброго времени суток. Я сейчас делаю что то подобное. Но проблема в программировании. Если Вы покажете более подробно как это сделать. Буду весьма благодарен....
How to connect line
Which?
Do you sell these?
Email me
@@MakerMan email address
@@MakerMando you sell these?
@@MakerManEmail address
👍
share firmware and wire contect pls
I wish we could buy this
Where are you located
@@MakerMan USA I can pay for shipping
I email me at mustangcrx@gmail.com.
Let's talk there.
@@MakerMan did you get my email
No actually, can you email again
Any one watching that can make me one please let me know
Email me
can you share wiring schema for remote controller, 08:21. scene